The DOI matches its Crossref record; 126 of the 126 references it cites were found in a registry or an index.
Recent Progress on Wear‐Resistant Materials: Designs, Properties, and Applications
Open accessAbstract
There has been tremendous interest in the development of different innovative wear‐resistant materials, which can help to reduce energy losses resulted from friction and wear by ≈40% over the next 10–15 years. This paper provides a comprehensive review of the recent progress on designs, properties, and applications of wear‐resistant materials, starting with an introduction of various advanced technologies for the fabrication of wear‐resistant materials and anti‐wear structures with their wear mechanisms. Typical strategies of surface engineering and matrix strengthening for the development of wear‐resistant materials are then analyzed, focusing on the development of coatings, surface texturing, surface hardening, architecture, and the exploration of matrix compositions, microstructures, and reinforcements. Afterward, the relationship between the wear resistance of a material and its intrinsic properties including hardness, stiffness, strength, and cyclic plasticity is discussed with underlying mechanisms, such as the lattice distortion effect, bonding strength effect, grain size effect, precipitation effect, grain boundary effect, dislocation or twinning effect. A wide range of fundamental applications, specifically in aerospace components, automobile parts, wind turbines, micro‐/nano‐electromechanical systems, atomic force microscopes, and biomedical devices are highlighted. This review is concluded with prospects on challenges and future directions in this critical field.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Contact and Rubbing of Flat Surfaces
Archard, J. F. (1953) · Journal of Applied Physics · doi:10.1063/1.1721448 · Cited by 7,892
Microstructures and properties of high-entropy alloys
Zhang, Y., Zuo, T. T., Tang, Z., Gao, M. C., Dahmen, K. A., Liaw, P. K., & Lu, Z. P. (2014) · Progress in Materials Science · doi:10.1016/j.pmatsci.2013.10.001 · Cited by 7,128
Robertson, J. (2002) · Materials Science and Engineering: R: Reports · doi:10.1016/s0927-796x(02)00005-0 · Cited by 6,206
Leyland, A., & Matthews, A. (2000) · Wear · doi:10.1016/s0043-1648(00)00488-9 · Cited by 3,103
3D printing of high-strength aluminium alloys
Martin, J. H., Yahata, B. D., Hundley, J. M., Mayer, J. A., Schaedler, T. A., & Pollock, T. M. (2017) · Nature · doi:10.1038/nature23894 · Cited by 2,950
Additively manufactured hierarchical stainless steels with high strength and ductility
Wang, Y. M., Voisin, T., McKeown, J. T., Ye, J., Calta, N. P., Li, Z., Zeng, Z., Zhang, Y., Chen, W., Roehling, T. T., et al. (2018) · Nature Materials · doi:10.1038/nmat5021 · Cited by 2,613
Chen, Q., & Thouas, G. A. (2015) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2014.10.001 · Cited by 2,398
Influence of tribology on global energy consumption, costs and emissions
Holmberg, K., & Erdemir, A. (2017) · Friction · doi:10.1007/s40544-017-0183-5 · Cited by 2,190
Resin composite—State of the art
Ferracane, J. L. (2011) · Dental Materials · doi:10.1016/j.dental.2010.10.020 · Cited by 2,188
Global energy consumption due to friction in passenger cars
Holmberg, K., Andersson, P., & Erdemir, A. (2012) · Tribology International · doi:10.1016/j.triboint.2011.11.022 · Cited by 1,614
Hygroscopic and hydrolytic effects in dental polymer networks
Ferracane, J. L. (2006) · Dental Materials · doi:10.1016/j.dental.2005.05.005 · Cited by 1,505
Graphene: a new emerging lubricant
Berman, D., Erdemir, A., & Sumant, A. V. (2014) · Materials Today · doi:10.1016/j.mattod.2013.12.003 · Cited by 1,480
Single layer and multilayer wear resistant coatings of (Ti,Al)N: a review
PalDey, S., & Deevi, S. C. (2003) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(02)00259-9 · Cited by 1,393
Recent advances in the development of aerospace materials
Zhang, X., Chen, Y., & Hu, J. (2018) · Progress in Aerospace Sciences · doi:10.1016/j.paerosci.2018.01.001 · Cited by 1,235
Additive manufacturing of ultrafine-grained high-strength titanium alloys
Zhang, D., Qiu, D., Gibson, M. A., Zheng, Y., Fraser, H. L., StJohn, D. H., & Easton, M. A. (2019) · Nature · doi:10.1038/s41586-019-1783-1 · Cited by 1,127
Microstructural design of hard coatings
Mayrhofer, P. H., Mitterer, C., Hultman, L., & Clemens, H. (2006) · Progress in Materials Science · doi:10.1016/j.pmatsci.2006.02.002 · Cited by 1,008
A concept for the design of novel superhard coatings
Veprek, S., & Reiprich, S. (1995) · Thin Solid Films · doi:10.1016/0040-6090(95)06695-0 · Cited by 981
Electroless nickel, alloy, composite and nano coatings – A critical review
Sudagar, J., Lian, J., & Sha, W. (2013) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2013.03.107 · Cited by 933
Dorri Moghadam, A., Omrani, E., Menezes, P. L., & Rohatgi, P. K. (2015) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2015.03.014 · Cited by 906
Hydrodynamic lubrication of textured surfaces: A review of modeling techniques and key findings
Gropper, D., Wang, L., & Harvey, T. J. (2015) · Tribology International · doi:10.1016/j.triboint.2015.10.009 · Cited by 905
Review Article: Stress in thin films and coatings: Current status, challenges, and prospects
Abadias, G., Chason, E., Keckes, J., Sebastiani, M., Thompson, G. B., Barthel, E., Doll, G. L., Murray, C. E., Stoessel, C. H., & Martinu, L. (2018) · Journal of Vacuum Science & Technology A: Vacuum, Surfaces, and Films · doi:10.1116/1.5011790 · Cited by 858
Mimicking the Lotus Effect: Influence of Double Roughness Structures and Slender Pillars
Patankar, N. A. (2004) · Langmuir · doi:10.1021/la048629t · Cited by 823
Nanomaterials as photothermal therapeutic agents
Chen, J., Ning, C., Zhou, Z., Yu, P., Zhu, Y., Tan, G., & Mao, C. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2018.07.005 · Cited by 749
Wakuda, M., Yamauchi, Y., Kanzaki, S., & Yasuda, Y. (2003) · Wear · doi:10.1016/s0043-1648(03)00004-8 · Cited by 708
Kinney, J. H., Marshall, S. J., & Marshall, G. W. (2003) · Critical Reviews in Oral Biology & Medicine · doi:10.1177/154411130301400103 · Cited by 701
Advances in engineered surfaces for functional performance
Bruzzone, A. A. G., Costa, H. L., Lonardo, P. M., & Lucca, D. A. (2008) · CIRP Annals · doi:10.1016/j.cirp.2008.09.003 · Cited by 692
Tribology of electroless nickel coatings – A review
Sahoo, P. K., & Das, S. K. (2010) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2010.11.013 · Cited by 614
Kovalchenko, A., Ajayi, O., Erdemir, A., Fenske, G., & Etsion, I. (2005) · Tribology International · doi:10.1016/j.triboint.2004.08.004 · Cited by 608
Surface composites by friction stir processing: A review
Sharma, V., Prakash, U., & Kumar, B. V. M. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.04.019 · Cited by 607
Solid Lubrication with MoS2: A Review
Vazirisereshk, M. R., Martini, A., Strubbe, D. A., & Baykara, M. Z. (2019) · Lubricants · doi:10.3390/lubricants7070057 · Cited by 605
Influence of surface texture on boundary lubricated sliding contacts
Pettersson, U., & Jacobson, S. (2003) · Tribology International · doi:10.1016/s0301-679x(03)00104-x · Cited by 556
Metal ion release from metal implants
Hanawa, T. (2004) · Materials Science and Engineering: C · doi:10.1016/j.msec.2004.08.018 · Cited by 528
Synergetic effects of surface texturing and solid lubricants to tailor friction and wear – A review
Rosenkranz, A., Costa, H. L., Baykara, M. Z., & Martini, A. (2021) · Tribology International · doi:10.1016/j.triboint.2020.106792 · Cited by 505
Global energy consumption due to friction in trucks and buses
Holmberg, K., Andersson, P., Nylund, N.-O., Mäkelä, K., & Erdemir, A. (2014) · Tribology International · doi:10.1016/j.triboint.2014.05.004 · Cited by 476
Carbon nanomaterials in tribology
Zhai, W., Srikanth, N., Kong, L. B., & Zhou, K. (2017) · Carbon · doi:10.1016/j.carbon.2017.04.027 · Cited by 470
Self-citationPolymers with autonomous life-cycle control
Patrick, J. F., Robb, M. J., Sottos, N. R., Moore, J. S., & White, S. R. (2016) · Nature · doi:10.1038/nature21002 · Cited by 434
Biologic effects of implant debris.
Hallab, N. J., & Jacobs, J. J. (2009) · PubMed · Cited by 422
Li, Y., Gao, T., Yang, Z., Chen, C., Kuang, Y., Song, J., Jia, C., Hitz, E. M., Yang, B., & Hu, L. (2017) · Nano Energy · doi:10.1016/j.nanoen.2017.09.034 · Cited by 416
Preparation, mechanical and anti-friction performance of MXene/polymer composites
Zhang, H., Wang, L., Chen, Q., Li, P., Zhou, A., Cao, X., & Hu, Q. (2016) · Materials & Design · doi:10.1016/j.matdes.2015.12.084 · Cited by 410
Tribology of two-dimensional materials: From mechanisms to modulating strategies
Zhang, S., Ma, T., Erdemir, A., & Li, Q. (2019) · Materials Today · doi:10.1016/j.mattod.2018.12.002 · Cited by 407
Prospects of laser welding technology in the automotive industry: A review
Hong, K.-M., & Shin, Y. C. (2017) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.02.008 · Cited by 376
2D nanomaterials as lubricant additive: A review
Xiao, H., & Liu, S. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.09.029 · Cited by 368
Liu, L., Zhou, M. J., Jin, L., Li, L., Mo, Y., Su, G., Li, X., Zhu, H., & Tian, Y. (2019) · Friction · doi:10.1007/s40544-019-0268-4 · Cited by 365
Nanoscale wear as a stress-assisted chemical reaction
Jacobs, T. D. B., & Carpick, R. W. (2013) · Nature Nanotechnology · doi:10.1038/nnano.2012.255 · Cited by 361
2D-nanomaterials for controlling friction and wear at interfaces
Spear, J. C., Ewers, B. W., & Batteas, J. D. (2015) · Nano Today · doi:10.1016/j.nantod.2015.04.003 · Cited by 346
Wear particles, periprosthetic osteolysis and the immune system
Goodman, S. B. (2007) · Biomaterials · doi:10.1016/j.biomaterials.2007.06.035 · Cited by 340
Recent progress on graphene-analogous 2D nanomaterials: Properties, modeling and applications
Liu, B., & Zhou, K. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2018.09.004 · Cited by 329
Self-citationGraphene: a multipurpose material for protective coatings
Nine, M. J., Cole, M. A., Tran, D. N. H., & Losic, D. (2015) · Journal of Materials Chemistry A · doi:10.1039/c5ta01010a · Cited by 325
Lubrication and wear modelling of artificial hip joints: A review
Mattei, L., Puccio, F. D., Piccigallo, B., & Ciulli, E. (2010) · Tribology International · doi:10.1016/j.triboint.2010.06.010 · Cited by 318
Extraordinary Macroscale Wear Resistance of One Atom Thick Graphene Layer
Berman, D., Deshmukh, S. A., Sankaranarayanan, S. K. R. S., Erdemir, A., & Sumant, A. V. (2014) · Advanced Functional Materials · doi:10.1002/adfm.201401755 · Cited by 309
Attar, H., Ehtemam-Haghighi, S., Kent, D., Okulov, I. V., Wendrock, H., Bönisch, M., Volegov, A. S., Calin, M., Eckert, J., & Dargusch, M. S. (2017) · Materials Science and Engineering A · doi:10.1016/j.msea.2017.01.096 · Cited by 297
Mechanotribological Aspects of MXene‐Reinforced Nanocomposites
Malaki, M., & Varma, R. S. (2020) · Advanced Materials · doi:10.1002/adma.202003154 · Cited by 292
Multiscale friction mechanisms and hierarchical surfaces in nano- and bio-tribology
Nosonovsky, M., & Bhushan, B. (2007) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2007.09.001 · Cited by 290
Lancaster, J. K. (1969) · Wear · doi:10.1016/0043-1648(69)90047-7 · Cited by 284
Atomistic Wear in a Single Asperity Sliding Contact
Gotsmann, B., & Lantz, M. A. (2008) · Physical Review Letters · doi:10.1103/physrevlett.101.125501 · Cited by 276
Luo, J., & Zhou, X. (2020) · Friction · doi:10.1007/s40544-020-0393-0 · Cited by 273
Nanomaterials in Superlubricity
Zhai, W., & Zhou, K. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201806395 · Cited by 269
Self-citationLi, Y., Wang, Q., & Wang, S. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.12.026 · Cited by 265
Ultralow nanoscale wear through atom-by-atom attrition in silicon-containing diamond-like carbon
Bhaskaran, H., Gotsmann, B., Sebastian, A., Drechsler, U., Lantz, M. A., Despont, M., Jaroenapibal, P., Carpick, R. W., Chen, Y., & Sridharan, K. (2010) · Nature Nanotechnology · doi:10.1038/nnano.2010.3 · Cited by 257
Multi-Scale Surface Texturing in Tribology—Current Knowledge and Future Perspectives
Grützmacher, P. G., Profito, F. J., & Rosenkranz, A. (2019) · Lubricants · doi:10.3390/lubricants7110095 · Cited by 223
Preparation and tribological properties of TiAl matrix composites reinforced by multilayer graphene
Xu, Z., Shi, X., Zhai, W., Yao, J., Song, S., & Zhang, Q. (2014) · Carbon · doi:10.1016/j.carbon.2013.09.077 · Cited by 210
Self-citationMo, J. L., Zhu, M. H., Lei, B., Leng, Y. X., & Huang, N. (2007) · Wear · doi:10.1016/j.wear.2007.01.051 · Cited by 206
Biomimetic multifunctional surfaces inspired from animals
Han, Z., Mu, Z., Yin, W., Li, W., Niu, S., Zhang, J., & Ren, L. (2016) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2016.03.004 · Cited by 193
Bahl, S., Suwas, S., & Chatterjee, K. (2021) · International Materials Reviews · doi:10.1080/09506608.2020.1735829 · Cited by 187
Review of Aluminum-To-Steel Welding Technologies for Car-Body Applications
Gullino, A., Matteis, P., & D’Aiuto, F. (2019) · Metals · doi:10.3390/met9030315 · Cited by 177
ADM guidance-ceramics: Fatigue principles and testing
Kelly, J. R., Cesar, P. F., Scherrer, S. S., Della Bona, A., van Noort, R., Tholey, M., Vichi, A., & Lohbauer, U. (2017) · Dental Materials · doi:10.1016/j.dental.2017.09.006 · Cited by 175
Voevodin, A. A., O’Neill, J. P., & Zabinski, J. S. (1999) · Thin Solid Films · doi:10.1016/s0040-6090(98)01456-4 · Cited by 171
Wear and Corrosion Interactions on Titanium in Oral Environment: Literature Review
Souza, J. C. M., Henriques, M., Teughels, W., Ponthiaux, P., Celis, J.-P., & Rocha, L. A. (2015) · Journal of Bio- and Tribo-Corrosion · doi:10.1007/s40735-015-0013-0 · Cited by 171
Li, X., Shi, T., Li, B., Chen, X., Zhang, C., Guo, Z., & Zhang, Q. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.108152 · Cited by 171
Application of graphene derivatives and their nanocomposites in tribology and lubrication: a review
Sun, J., & Du, S. (2019) · RSC Advances · doi:10.1039/c9ra05679c · Cited by 168
Recent advances in understanding the fatigue and wear behavior of dental composites and ceramics
Kruzic, J. J., Arsecularatne, J. A., Tanaka, C. B., Hoffman, M., & Cesar, P. F. (2018) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2018.08.008 · Cited by 165
Advanced characterization methods for wear resistant hard coatings: A review on recent progress
Tkadletz, M., Schalk, N., Daniel, R., Keckes, J., Czettl, C., & Mitterer, C. (2016) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2015.11.016 · Cited by 160
Ultra-Wear-Resistant MXene-Based Composite Coating via in Situ Formed Nanostructured Tribofilm
Yin, X., Jin, J., Chen, X., Rosenkranz, A., & Luo, J. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b11449 · Cited by 153
The Effects of Dopants on the Chemistry and Tribology of Sputter-Deposited MoS 2 Films
Zabinski, J. S., Donley, M. S., Walck, S. D., Schneider, T. R., & McDevitt, N. T. (1995) · Tribology Transactions · doi:10.1080/10402009508983486 · Cited by 152
Mechanical and tribological properties of nanocomposites incorporated with two-dimensional materials
Ji, Z., Zhang, L., Xie, G., Xu, W., Guo, D., Luo, J., & Prakash, B. (2020) · Friction · doi:10.1007/s40544-020-0401-4 · Cited by 145
2D nano-materials beyond graphene: from synthesis to tribological studies
Rosenkranz, A., Liu, Y., Yang, L., & Chen, L. (2020) · Applied Nanoscience · doi:10.1007/s13204-020-01466-z · Cited by 144
Self-citationMarian, M., Song, G., Wang, B., Fuenzalida, V. M., Krauß, S., Merle, B., Tremmel, S., Wartzack, S. J., Yu, J., & Rosenkranz, A. (2020) · Applied Surface Science · doi:10.1016/j.apsusc.2020.147311 · Cited by 143
Effectiveness and design of surface texturing for different lubrication regimes
Podgornik, B., Vilhena, L., Sedlaček, M., Rek, Z., & Žun, I. (2012) · Meccanica · doi:10.1007/s11012-012-9540-7 · Cited by 135
Bio-inspired textures for functional applications
Malshe, A. P., Bapat, S., Rajurkar, K. P., & Haitjema, H. (2018) · CIRP Annals · doi:10.1016/j.cirp.2018.05.001 · Cited by 134
Superlubricity of two-dimensional fluorographene/MoS2heterostructure: a first-principles study
Wang, L., Ma, T., Hu, Y., Zheng, Q., Wang, H., & Luo, J. (2014) · Nanotechnology · doi:10.1088/0957-4484/25/38/385701 · Cited by 130
Hynowska, A., Pellicer, E., Fornell, J., González, S., Steenberge, N. V., Suriñach, S., Gebert, A., Calin, M., Eckert, J., Baró, M. D., et al. (2012) · Materials Science and Engineering C · doi:10.1016/j.msec.2012.07.016 · Cited by 128
Liu, C., Bi, Q., & Matthews, A. (2002) · Surface and Coatings Technology · doi:10.1016/s0257-8972(02)00630-8 · Cited by 128
Magalhães, A., Gomes, J., Ismail, M. N., Haslam, S. M., Mendes, N. M., Osório, H., David, L., LePendu, J., Haas, R., Dell, A., et al. (2009) · Glycobiology · doi:10.1093/glycob/cwp131 · Cited by 128
Mechanical properties and frictional resistance of Al composites reinforced with Ti3C2T MXene
Hu, J., Li, S., Zhang, J., Chang, Q., Yu, W., & Zhou, Y. (2019) · Chinese Chemical Letters · doi:10.1016/j.cclet.2019.09.004 · Cited by 127
Microwave heating and its applications in surface engineering: a review
Vasudev, H., Singh, G., Bansal, A., et al. (2019) · Materials Research Express · doi:10.1088/2053-1591/ab3674 · Cited by 121
Tribological behaviour of hard coatings deposited by arc-evaporation PVD
Rodríguez, R., García, J. A., Medrano, Á. A., et al. (2002) · Vacuum · doi:10.1016/s0042-207x(02)00248-8 · Cited by 118
Electroless Ni–P–SiC composite coatings with superfine particles
Jiaqiang, G., Liu, L., Wu, Y., Bin, S., & Hu, W. (2005) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2005.08.134 · Cited by 117
Tribology of 2D Nanomaterials: A Review
Uzoma, P. C., Hu, H., Khadem, M., & Penkov, O. V. (2020) · Coatings · doi:10.3390/coatings10090897 · Cited by 117
Increasing nanohardness and reducing friction of nitride steel by laser surface texturing
Gualtieri, E., Borghi, A., Calabri, L., Pugno, N. M., & Valeri, S. (2008) · Tribology International · doi:10.1016/j.triboint.2008.09.008 · Cited by 112
Single asperity tribochemical wear of silicon nitride studied by atomic force microscopy
Maw, W. S., Stevens, F., Langford, S. C., & Dickinson, J. T. (2002) · Journal of Applied Physics · doi:10.1063/1.1510595 · Cited by 111
Oxidation and wear behaviors of Ti-based thin films
Hsieh, J. H., Tan, A. L. K., & Zeng, X. (2006) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2006.08.026 · Cited by 110
Jiang, Y., Jia, T., Wooley, P. H., & Yang, S. (2013) · PubMed · Cited by 107
Oil film lifetime and wear particle analysis of laser-patterned stainless steel surfaces
Rosenkranz, A., Heib, T., Gachot, C., & Mücklich, F. (2015) · Wear · doi:10.1016/j.wear.2015.04.006 · Cited by 102
Irreversibility as a Symmetry-breaking Process
PRIGOGINE, I. (1973) · Nature · doi:10.1038/246067a0 · Cited by 101
Bonding, degradation, and environmental effects on novel perfluoropolyether lubricants
Tao, Z., & Bhushan, B. (2005) · Wear · doi:10.1016/j.wear.2005.01.013 · Cited by 97
Guo, W., Wu, Y., Zhang, J., et al. (2014) · Journal of Thermal Spray Technology · doi:10.1007/s11666-014-0096-z · Cited by 96
Accelerated precipitation and growth of phases in an Al-Zn-Mg-Cu alloy processed by surface abrasion
Wang, S.-S., Jiang, J., Fan, G., Panindre, A. M., Frankel, G. S., & Zhen, L. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.03.074 · Cited by 95
Optimizing Bulk Metallic Glasses for Robust, Highly Wear‐Resistant Gears
Hofmann, D. C., Andersen, L. M., Kolodziejska, J. A., Roberts, S. N., Borgonia, J. P., Johnson, W. L., Vecchio, K. S., & Kennett, A. (2016) · Advanced Engineering Materials · doi:10.1002/adem.201600541 · Cited by 86
Friction and wear behavior of PTFE coatings modified with poly (methyl methacrylate)
Peng, S., Zhang, L., Xie, G., Guo, Y., Si, L., & Luo, J. (2019) · Composites Part B Engineering · doi:10.1016/j.compositesb.2019.04.047 · Cited by 82
Metal Oxide Nanosheets as 2D Building Blocks for the Design of Novel Materials
Timmerman, M. A., Xia, R., Le, P. T. P., Wang, Y., & ten Elshof, J. E. (2020) · Chemistry - A European Journal · doi:10.1002/chem.201905735 · Cited by 70
Laser-Assisted Cold-Sprayed Corrosion- and Wear-Resistant Coatings: A Review
Olakanmi, E. O., & Doyoyo, M. (2014) · Journal of Thermal Spray Technology · doi:10.1007/s11666-014-0098-x · Cited by 67
Zafari, A., Ghasemi, H. M., & Mahmudi, R. (2013) · Wear · doi:10.1016/j.wear.2013.02.016 · Cited by 65
Suarez, S., Rosenkranz, A., Gachot, C., et al. (2013) · Carbon · doi:10.1016/j.carbon.2013.08.054 · Cited by 64
Zwahr, C., Helbig, R., Werner, C., et al. (2019) · Scientific Reports · doi:10.1038/s41598-019-43055-3 · Cited by 64
Thompson, M. W., Gilmer, J., Matsumoto, R. A., Quach, C. D., Shamaprasad, P., Yang, A. H., Iacovella, C. R., McCabe, C., & Cummings, P. T. (2020) · Molecular Physics · doi:10.1080/00268976.2020.1742938 · Cited by 60
Ghosh, S., Choudhury, D., Roy, T., Mamat, A., Masjuki, H. H., & Pingguan‐Murphy, B. (2015) · Science and Technology of Advanced Materials · doi:10.1088/1468-6996/16/3/035002 · Cited by 59
Chai, L., Wang, C., Xiang, K., Wang, Y., Wang, T., & Ma, Y. L. (2020) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2020.126503 · Cited by 59
Mechanics of microwear traces in tooth enamel
Borrero‐López, Ó., Pajares, A., Constantino, P. J., & Lawn, B. R. (2014) · Acta Biomaterialia · doi:10.1016/j.actbio.2014.11.047 · Cited by 57
Nano-friction behavior of phosphorene
Bai, L., Лю, Б., Srikanth, N., Tian, Y., & Zhou, K. (2017) · Nanotechnology · doi:10.1088/1361-6528/aa7a2a · Cited by 50
Self-citationZhang, L., Ren, Y., Peng, S., Guo, D., Wen, S., Luo, J., & Xie, G. (2019) · Nanoscale · doi:10.1039/c9nr00767a · Cited by 48
Elinski, M. B., Liu, Z., Spear, J., & Batteas, J. D. (2017) · Journal of Physics D Applied Physics · doi:10.1088/1361-6463/aa58d6 · Cited by 47
Hemler, S. L., Charbonneau, D. N., & Beschorner, K. E. (2020) · Tribology International · doi:10.1016/j.triboint.2020.106161 · Cited by 46
Wear‐Resistant Nanoscale Silicon Carbide Tips for Scanning Probe Applications
Lantz, M. A., Gotsmann, B., Jaroenapibal, P., Jacobs, T. D. B., O’Connor, S. D., Sridharan, K., & Carpick, R. W. (2012) · Advanced Functional Materials · doi:10.1002/adfm.201102383 · Cited by 44
Velocity dependence of nanoscale wear in atomic force microscopy
Bhushan, B., & Kwak, K. J. (2007) · Applied Physics Letters · doi:10.1063/1.2800375 · Cited by 40
Tactile perception of skin and skin cream by friction induced vibrations
Ding, S., & Bhushan, B. (2016) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2016.07.034 · Cited by 39
An energy-based model to predict wear in nanocrystalline diamond atomic force microscopy tips
Agrawal, R., Moldovan, N., & Espinosa, H. D. (2009) · Journal of Applied Physics · doi:10.1063/1.3223316 · Cited by 38
Direct Laser Interference Patterning of Bioceramics: A Short Review
Fabris, D., Lasagni, A. F., Fredel, M. C., & Henriques, B. A. P. D. C. (2019) · Ceramics · doi:10.3390/ceramics2040045 · Cited by 31
Attrition-corrosion of human dental enamel: A review
Wu, Y., Arsecularatne, J. A., & Hoffman, M. (2017) · Biosurface and Biotribology · doi:10.1016/j.bsbt.2017.12.001 · Cited by 29
Robust sandwich micro-structure coating layer for wear-resistant conductive polyester fabrics
Zhao, H., Tian, M., Li, Z., Zhang, Y., Chen, Z., Zhang, W., Zhu, S., Sun, Y., Zhou, Z., & Qu, L. (2019) · Applied Surface Science · doi:10.1016/j.apsusc.2019.07.103 · Cited by 28
Effect of graphene nanoplate addition on the tribological performance of Ni 3 Al matrix composites
Zhai, W., Shi, X., Wang, M., Xu, Z., Yao, J., Song, S., Wang, Y., & Zhang, Q. (2013) · Journal of Composite Materials · doi:10.1177/0021998313513048 · Cited by 26
Self-citationNanotribological and wetting performance of hierarchical patterns
Grewal, H. S., Piao, S., Cho, I., Jhang, K.-Y., & Yoon, E.-S. (2015) · Soft Matter · doi:10.1039/c5sm01649e · Cited by 26
Nanotribology of 2D materials and their macroscopic applications
Lee, J. H., Cho, D., Park, B. H., & Choi, J. S. (2020) · Journal of Physics D Applied Physics · doi:10.1088/1361-6463/ab9670 · Cited by 26
Increase of Traction Coefficient due to Surface Microtexture
Nanbu, T., Yasuda, Y., Ushijima, K., Watanabe, J., & Zhu, D. S. (2007) · Tribology Letters · doi:10.1007/s11249-007-9287-9 · Cited by 24
Impacts of the substrate stiffness on the anti-wear performance of graphene
Yao, Q., Qi, Y., Zhang, J., Zhang, S., Zhao, P., Wang, H., Feng, X., & Li, Q. (2019) · AIP Advances · doi:10.1063/1.5095055 · Cited by 22
Kakulite, K. K., Panwar, S. S., & Kandasubramanian, B. (2019) · SN Applied Sciences · doi:10.1007/s42452-019-0924-3 · Cited by 13
Cited by
Heterostructured stainless steel: Properties, current trends, and future perspectives
Romero-Resendiz, L., El-Tahawy, M., Zhang, T., Rossi, M. C., Marulanda-Cardona, D. M., Yang, T., Amigó-Borrás, V., Huang, Y., Mirzadeh, H., Beyerlein, I. J., et al. (2022) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2022.100691 · Cited by 278
Metadata
- Authors
- Zhai, W., Bai, L., Zhou, R., Fan, X., Kang, G., Liu, Y., & Zhou, K.
- Venue
- Advanced Science
- Publisher
- Wiley
- Published
- 2021-03-24
- Volume
- 8
- Issue
- 11
- Pages
- e2003739-e2003739
- ISSN
- 2198-3844 (ISSN-L)
- OpenAlex
- W3136728280
- Cited by
- 651
- References
- 126
- FWCI
- 22.71
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.