The DOI matches its Crossref record.
Structure of skin layer in injection‐molded polypropylene
Abstract
The structure of skin layer in injection‐molded polypropylen which displayed a clear two‐phase structure of skin and core has been studied by means of wide‐angle x‐ray diffraction, small‐angle x‐ray scattering, melting behavior, density, dynamic viscoelasticity, and tensile test. In skin layer, the c‐axis and a*‐axis were highly oriented to the machine direction (MD), and the plane of the lamellar structure of about 160 Å in thickness was in normal to MD. The density was about 0.907 g/cm 3, which was nearly the same as that of core layer. Although the majority of crystallites melted in the same temperature range as in that of the core layer, there was about 5.3% higher temperature melting structure (Tm = 182°C). The dynamic tensile modulus E′ in MD decreased more slowly with increasing temperature than that of the core layer and held high modulus in the range of ca. 30°C, just above the temperature at which E′ of the core layer suddenly dropped. E′ in MD was higher than that in TD in the temperature range below 33°C, which was slightly higher than the primary absorption temperature, and the order reversed above 33°C. The tensile yield stress in MD was 1.5 times higher than that of the core layer. The skin layer in MD ruptured just after yielding and did not show necking. The tensile yield stress in TD was about half of that in MD about 0.7 times that of the core layer. The necking stress in TD was about 0.6 times that of the core layer. In general, a polypropylene melt crystallizes under a high shear stress in injection molding. From these facts, it was concluded that the skin layer is composed of so‐called “shishkebab”‐like main skeleton structures, whose axis is parallel to MD, piled epitaxially with a*‐axis‐oriented imperfect lamellar substructure.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
White, J. R., & Turnbull, A. (1994) · Journal of Materials Science · doi:10.1007/bf00445969 · Cited by 305
Modeling of morphology evolution in the injection molding process of thermoplastic polymers
Pantani, R., Coccorullo, I., Speranza, V., & Titomanlio, G. (2005) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2005.09.001 · Cited by 293
Lin, M.-C., Chen, H.-L., Lin, W.-F., Huang, P.-S., & Tsai, J.-C. (2012) · The Journal of Physical Chemistry B · doi:10.1021/jp306410j · Cited by 27
Metadata
- Authors
- Fujiyama, M., Wakino, T., & Kawasaki, Y.
- Venue
- Journal of Applied Polymer Science
- Publisher
- Wiley
- Published
- 1988-01
- Volume
- 35
- Issue
- 1
- Pages
- 29-49
- ISSN
- 0021-8995 (ISSN-L)
- 1097-4628
- OpenAlex
- W2026193281
- Cited by
- 248
- References
- 0
- FWCI
- 3.14
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Structure of skin layer in injection‐molded polypropylene. https://app.cochat.ai/papers/10.1002/app.1988.070350104
- The paper
- Fujiyama, M., Wakino, T., & Kawasaki, Y. (1988). Structure of skin layer in injection‐molded polypropylene. Journal of Applied Polymer Science. https://doi.org/10.1002/app.1988.070350104
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.