The DOI matches its Crossref record; 7 of the 7 references it cites were found in a registry or an index.
The effect of crosslinking on the mechanical properties of polylactic acid/polycaprolactone blends
Abstract
The improvement of the brittle behavior of Polylactic acid (PLA) resin was studied by blending it with Polycaprolactone (PCL) resin. These materials were fabricated into the compressed films and injection moldings. The values of tensile modulus and strength were appropriate, judging from the rule of mixtures. However, the ultimate tensile strain was very small. Dicumyl peroxide (DCP) was added to this blend system to improve its ultimate tensile strain. It was found that the value of ultimate tensile strain peaked at low DCP concentration. The samples at low DCP contents show yield point and ductile behavior under tensile test. The impact strength of the optimum composition was 2.5 times superior to neat PLA, and ductile behavior such as plastic deformation was observed at its fracture surface. It was found that the carbonyl groups of the blend material with DCP were altered by using FTIR spectroscopy. Dynamic mechanical analysis data revealed the dual phase nature of PLA/PCL blend albeit with good interfacial adhesion, and the DCP enhanced the viscous property in PCL phase, which agreed with tensile ductility and impact strength. The mechanical properties of this blend are comparable to those of general purpose HIPS and ABS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1816–1825, 2006
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Polymer Interface and Adhesion
Wu, S. (2017) · Routledge eBooks · doi:10.1201/9780203742860 · Cited by 3,379
Kister, G., Cassanas, G., & Vert, M. (1998) · Polymer · doi:10.1016/s0032-3861(97)00229-2 · Cited by 689
Poly(lactic acid)/organoclay nanocomposites: Thermal, rheological properties and foam processing
Di, Y., Iannace, S., Maio, E. D., & Nicolais, L. (2005) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.20366 · Cited by 257
Maleation of polylactide (PLA) by reactive extrusion
Carlson, D., Nie, L., Narayan, R., & Dubois, P. (1999) · Journal of Applied Polymer Science · doi:10.1002/(sici)1097-4628(19990425)72:4<477::aid-app3>3.0.co;2-q · Cited by 242
Ishiaku, U. S., Pang, K. W. P., Lee, W. S., & Ishak, Z. A. M. (2002) · European Polymer Journal · doi:10.1016/s0014-3057(01)00125-2 · Cited by 141
Self-citationEffects of molecular architecture on two‐step, melt‐spun poly(lactic acid) fibers
Cicero, J. A., Dorgan, J. R., Garrett, J. T., Runt, J. P., & Lin, J. S. (2002) · Journal of Applied Polymer Science · doi:10.1002/app.11268 · Cited by 95
On mechanical properties of sago starch/poly(ε‐caprolactone) composites
Odusanya, O. S., Ishiaku, U. S., Azemi, B. M. N. M., Manan, B. D. M., & Kammer, H. W. (2000) · Polymer Engineering and Science · doi:10.1002/pen.11258 · Cited by 21
Self-citation
Cited by
Poly(lactic acid) modifications
Rasal, R. M., Janorkar, A. V., & Hirt, D. E. (2010) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2009.12.003 · Cited by 2,204
Poly (lactic acid) blends: Processing, properties and applications
Nofar, M., Sacligil, D., Carreau, P. J., Kamal, M. R., & Heuzey, M.-C. (2019) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2018.12.002 · Cited by 780
Research progress in toughening modification of poly(lactic acid)
Liu, H., & Zhang, J. (2011) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.22283 · Cited by 767
Rapid prototyping of continuous carbon fiber reinforced polylactic acid composites by 3D printing
Li, N., Li, Y., & Liu, S. (2016) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2016.07.025 · Cited by 707
Polylactic acid blends: The future of green, light and tough
Hamad, K., Kaseem, M., Ayyoob, M., Joo, J., & Deri, F. (2018) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2018.07.001 · Cited by 640
Metadata
- Authors
- Semba, T., Kitagawa, K., Ishiaku, U. S., & Hamada, H.
- Venue
- Journal of Applied Polymer Science
- Publisher
- Wiley
- Published
- 2006-05-24
- Volume
- 101
- Issue
- 3
- Pages
- 1816-1825
- ISSN
- 0021-8995 (ISSN-L)
- 1097-4628
- OpenAlex
- W1968761716
- Cited by
- 315
- References
- 7
- FWCI
- 3.84
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.