CoChat

Improvement of Flexural Strengths of Poly(L‐lactic acid) by Solid‐State Extrusion, 2. Extrusion Through Rectangular Die

Lim, Jung Yul, Kim, Soo Hyun, Lim, Soonho, Kim, Young Ha · 2003 · Macromolecular Materials and Engineering

The DOI matches its Crossref record; 20 of the 20 references it cites were found in a registry or an index.

Abstract

Solid‐state extrusion of poly (L‐lactic acid) (PLLA) through rectangular die was performed to produce high flexural strength plates that can be used as internal fixation devices. A single‐angle wedge‐shaped rectangular die was utilized having the die exit dimension of 4 mm × 1 mm. Billets were machined out from vacuum compression molded PLLA having different crystallinities to have various thicknesses and thus various imposed draw ratios. Solid‐state extrusion of billets was performed at various drawing rates at 130 °C, above glass transition and below melting temperature. Extruded plates had the width and thickness smaller than the die due to the further drawing outside the die. The decrease in width was larger than the decrease in thickness, and this became more prominent with increasing draw ratio and drawing rate, resulting in a significantly smaller aspect ratio. Contributions of die drawing and further drawing outside the die were estimated from the extruded plate dimensions, by which the drawing rate effect was attributed to the further drawing outside the die. As actual draw ratio increased, crystallinity, melting temperature, crystalline orientation factor, and birefringence increased. Throughout the whole process the decrease in molecular weight was largely suppressed to be about 10%. As billet crystallinity, draw ratio, and drawing rate increased, both flexural strength and flexural modulus increased up to the maxima of 202 MPa and 9.7 GPa, respectively. This enhancement in mechanical properties was correlated with structural developments. Changes in flexural strength of solid‐state extruded PLLA plates as a function of draw ratio (the effect of drawing rate is co‐plotted by hollow symbols at corresponding draw ratio.). magnified imageChanges in flexural strength of solid‐state extruded PLLA plates as a function of draw ratio (the effect of drawing rate is co‐plotted by hollow symbols at corresponding draw ratio.).

Overview

Integrity signals

Registry

Crossref · 10.1002/mame.200290033

Cites

20 of 20 references verified0 citation errors · 0 not checkable

Statistics

Recomputing p-values needs the paper’s full text.

Verification

Claims the paper makes

This paper’s full text isn’t openly available, so its claims and self-check weren’t run. The registry and citation checks still apply.

Citations

Cites

Show all 20 references

Research works printed but not linked: 1

  1. 10.1016/0032-3861(82)90176-8 · DOI · Paper page

Cited by

See all 20

Metadata

Authors
Lim, J. Y., Kim, S. H., Lim, S., & Kim, Y. H.
Affiliations
Korean Association Of Science and Technology Studies (KR)
Corresponding author
Kim, Soo Hyun
Venue
Macromolecular Materials and Engineering
Publisher
Wiley
Published
2003-01
Volume
288
Issue
1
Pages
50-57
ISSN
  • 1438-7492 (ISSN-L)
  • 1439-2054
OpenAlex
W2086508332
Cited by
20
References
20
Citations by year
2023: 1 · 2022: 1 · 2021: 1 · 2020: 1 · 2019: 1 · 2018: 3 · 2017: 1 · 2016: 3 · 2012: 1
FWCI
0.61
Type
journal article
Language
en
Open access
closed
Locations
Macromolecular Materials and Engineering (publishedVersion)
Topics
  • Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
  • Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
  • Physical Sciences › Engineering › Mechanical Engineering › Injection Molding Process and Properties
Keywords
poly(L-lactic acid), solid-state extrusion, flexural strength, flexural modulus, crystallinity, crystal orientation, birefringence, molecular weight degradation, draw ratio, drawing rate, aspect ratio, internal fixation devices, biodegradable polymers

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Improvement of Flexural Strengths of Poly(L‐lactic acid) by Solid‐State Extrusion, 2. Extrusion Through Rectangular Die. https://app.cochat.ai/papers/10.1002/mame.200290033
The paper
Lim, J. Y., Kim, S. H., Lim, S., & Kim, Y. H. (2003). Improvement of Flexural Strengths of Poly(L‐lactic acid) by Solid‐State Extrusion, 2. Extrusion Through Rectangular Die. Macromolecular Materials and Engineering. https://doi.org/10.1002/mame.200290033

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.