The DOI matches its Crossref record; 18 of the 18 references it cites were found in a registry or an index; 1 of the 26 sources its claims cite were checked for support.
The role of dihydroxybenzenes and oxygen on the corrosion of steel in black liquor
Overview
CoChat Summary
TL;DR
In alkaline solutions simulating black liquor at 65°C, 1,2-dihydroxybenzenes such as catechol and pyrogallol increased the critical current density for passivation of A-283 Gr C steel, while guaiacol, resorcinol, and p-hydroquinone did not. Aeration oxidized these dihydroxybenzenes to quinones, raising the steel’s corrosion potential and, depending on concentration and sulfide presence, causing either pitting or high-rate uniform corrosion.
Key findings
- Catechol at 1 g/L raised the critical current density for passivation to 440 µA/cm² and broadened the active-passive transition from 76 to over 230 mV; passive current density increased by about an order of magnitude. At 10 g/L catechol, i_crit, i_pass, and transition width increased further. Corrosion rate at OCP was 36 µA/cm² in 1 g/L catechol and 48 µA/cm² in 10 g/L catechol.
- Only adjacent-hydroxyl dihydroxybenzenes increased i_crit: pyrogallol and catechol did, while guaiacol, resorcinol, and p-hydroquinone had no effect on i_crit. Passive current density was 1 µA/cm² in NaOH and nonaggressive phenols, 2 µA/cm² with 10 g/L pyrogallol, and 10 µA/cm² with 10 g/L catechol.
- Aeration oxidized catechol and p-hydroquinone to quinones, raising redox potential. Catechol raised steel OCP approximately 120 mV upon aeration and caused uniform corrosion; p-hydroquinone raised steel OCP to match Pt and showed no visible attack. With 1 g/L catechol + 10 g/L Na₂S, aeration produced large pits 40–50 µm in diameter, versus only small pits without catechol.
- At higher catechol concentrations, passivation upon aeration was prevented because i_crit exceeded the diffusion-limited current for quinone reduction, leading to high-rate uniform corrosion up to approximately 0.8 mA/cm². Catechol-containing solutions attacked Fe(II)-containing oxides more than Fe(III) oxides; p-hydroquinone or NaOH caused no significant oxide weight loss.
Methods
- Potentiodynamic polarization (steel 0.1 mV/s; Pt 1 mV/s), potentiostatic holds (8 or 16 h), and OCP monitoring under deaeration then aeration (total 12,000 s) were performed on A-283 Gr C steel (0.15 C, 0.49 Mn, 0.011 P, 0.015 S, 0.08 Si, balance Fe) and Pt in pH 13.4 solutions at 65°C. Base solutions used 10 g/L NaOH, 0.1 M sulfate, and additions of Na₂S, catechol, pyrogallol, guaiacol, resorcinol, or p-hydroquinone.
- Corrosion rates at OCP were calculated with PARCALC in SoftCorrII; surfaces were examined after tests, including EDS of pits. Iron oxide powder dissolution tests exposed 3.000 g of FeO, Fe₂O₃, or Fe₃O₄ to deaerated alkaline solutions for 12 h, then filtered and weighed the powder.
Limitations
- The paper has no formal limitations section. It states that the interaction between sulfide and catechol is “not clearly understood” and that the mechanism by which catechols inhibit passivation is proposed via soluble complex formation and iron oxide destabilization.
- Evident from the text: the work uses synthetic alkaline solutions and one steel grade (A-283 Gr C) at 65°C, so extrapolation to the full range of black liquor compositions, temperatures, and mill conditions is limited.
- Evident: the iron oxide experiments use pure oxide powders rather than actual passive films, and the phenol set is limited to selected substituted phenols.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 2 Not valid · 22 Not checked · 102 Own results and interpretations
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The quinones led to an increase in potential and a fall in pH at longer times due to their hydrolysis.25”
§ DISCUSSION > 0.7 -
What the sources say
- Could not verifycites [25] Ryan, 1980, J. Electrochem. Soc. sourceExperimental — accuracy not yet measured
The Conclusions (page unavailable) say that substituted catechols form quinones and that a different measure—the coulometric n-value—increases at long electrolysis times, attributing that increase to polymeric products and catechol depletion. The Results and Conclusions do not report a longer-term rise in potential or fall in pH caused by quinone hydrolysis (searched for hydrolysis and the claimed potential–pH changes). (LLM, conf=0.72)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Above -0.5 V (SCE) large current densities were observed on both steel and platinum (see Figs 2 and 4).”
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The active-passive transition was also broadened in potential, increasing from 76 to over 230 mV in the presence of catechol.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“No sulfide was present in these solutions, precluding any role of polysulfides or other dissolved sulfur species.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In both cases the aeration led to a large increase in the redox potential of the solution as shown by the increase in the OCP of Pt.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
69 more claims
Create a free account to see all 126 claims and every source verdict.
- Probably not a substantial claim. 12
- It may state two separate claims as one. 39
- The quote only partly states this claim. 5
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The cited source says what the claim attributes to it.
In the citing paper
“Inorganic constituents of black liquor alone do not correlate well with the corrosivity of diVerent black liquors.”
From Effect of wood species on corrosion behavior of carbon steel and stainless steels in black liquors (2007) · cites this paper as [16]
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 1066 S. Kannan and R. G. Kelly
“Upon aeration, the formation of polysulfides (or other oxidizing sulfur species) leads to increases of the corrosion potential into the passive region (Fig. 15, solid curve a, cathodic line 2).”
§ 1066 S. Kannan and R. G. Kelly
“Fig. 14. Schematic representation of the corrosion behavior of carbon steel exposed to black liquor. The solid curve a represents the anodic behavior of steel when no dihydroxybenzenes are present.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
“However, the current density quickly fell to 10 PA cms2 and increased only slightly during the remainder of the test (11.3 h).”
Reported 11.3 · recomputed 10.3
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 0 3600 7200 10600 14400 16000
“Fig. 5. Optical micrograph of a large pit observed on the steel electrode held at -0.5 V (SCE) in 10 g I- ' Na2S (pH 13.4) at 65°C for 8 h (see Fig. 4 for current-time data).”
§ 0 3600 7200 10600 14400 16000
“Fig. 4. A potentiostatic test of steel held at -0.5 V (SCE) in 10 g I-' Na$ (pH 13.4)at 65 "C for 4 h. Note increasing current with time.”
Citations
Cites
Handbook for Pulp and Paper Technologists
Smook, G. A. (1982) · Cited by 876
Avdeef, A., Sofen, S. R., Bregante, T. L., & Raymond, K. N. (1978) · Journal of the American Chemical Society · doi:10.1021/ja00485a018 · Cited by 313
The Electrochemical Oxidation of Substituted Catechols
Ryan, M. D., Yueh, A., & Chen, W. (1980) · Journal of The Electrochemical Society · doi:10.1149/1.2129936 · Cited by 210
Electrochemical behaviour of iron in alkaline sulphide solutions
Shoesmith, D. W., Taylor, P., Bailey, M. G., & Ikeda, B. (1978) · Electrochimica Acta · doi:10.1016/0013-4686(78)87014-5 · Cited by 122
Use of Mössbauer Spectroscopy to Study Reaction Products of Polyphenols and Iron Compounds
Gust, J., & Suwalski, J. (1994) · CORROSION · doi:10.5006/1.3294344 · Cited by 117
FIESER, L. F., & FIESER, M. (1956) · Soil Science · doi:10.1097/00010694-195611000-00014 · Cited by 110
The effect of potential scan rate on the parameters used to synthesize anodic polarization curves
Otieno-Alego, V., Hope, G. A., Flitt, H. J., Cash, G. A., & Schweinsberg, D. P. (1992) · Corrosion Science · doi:10.1016/0010-938x(92)90004-m · Cited by 48
Research works printed but not linked: 5
- Page, 1989, Mater. Perform., 28, 58
- Munro, 1993, Minutes of NACE Task Group T-5H-14 (Black liquor corrosion)
- MacLean, 1953, Pulp Pap. Mag. Can., 54, 125
- Tonsi-Eldakar, 1982, Corrosion/82, Paper No. 91
- Kipton, 1982, Aust. J. Chem., 24, 739
Cited by
Aourabi, S., Driouch, M., Sfaira, M., Mahjoubi, F., Hammouti, B., Verma, C., Ebenso, E. E., & Guo, L. (2020) · Journal of Molecular Liquids · doi:10.1016/j.molliq.2020.114950 · Cited by 78
The effect of tannins and pH on the corrosion of steel in wood extracts
Zelinka, S. L., & Stone, D. S. (2010) · Materials and Corrosion · doi:10.1002/maco.201005845 · Cited by 54
Effect of wood species on corrosion behavior of carbon steel and stainless steels in black liquors
Singh, P. M., & Anaya, A. (2007) · Corrosion Science · doi:10.1016/j.corsci.2006.04.020 · Cited by 33
Electrochemical Thermodynamics and Kinetics of Relevance to Corrosion
(2002) · doi:10.1201/9780203909133.ch2 · Cited by 18
Self-citation
Metadata
- Authors
- Kannan, S., & Kelly, R. G.
- Affiliations
- University of Virginia (US)
- ORCID
- Kelly, R.G.
- Venue
- Corrosion Science
- Publisher
- Elsevier BV
- Published
- 1996-07
- Volume
- 38
- Issue
- 7
- Pages
- 1051-1069
- ISSN
- 0010-938X (ISSN-L)
- OpenAlex
- W1975091876
- Semantic Scholar
- 16c65b90c65d98307d4633bff2957a991a960816
- Cited by
- 16
- References
- 17
- Citations by year
- 2024: 1 · 2023: 1 · 2020: 2 · 2018: 1 · 2017: 1 · 2014: 1
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
- Locations
- Corrosion Science (publishedVersion)
- Topics
- Physical Sciences › Materials Science › Materials Chemistry › Corrosion Behavior and Inhibition
- Physical Sciences › Materials Science › Metals and Alloys › Hydrogen embrittlement and corrosion behaviors in metals
- Physical Sciences › Engineering › Civil and Structural Engineering › Concrete Corrosion and Durability
- Keywords
- steel corrosion, black liquor, dihydroxybenzenes, substituted phenols, dissolved oxygen, passivation, critical current density, quinone formation, sulfide ions, pitting corrosion, general corrosion, paper industry, steel storage tanks, alkaline solution
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The role of dihydroxybenzenes and oxygen on the corrosion of steel in black liquor. https://app.cochat.ai/papers/10.1016/0010-938x(96)00186-2
- The paper
- Kannan, S., & Kelly, R. G. (1996). The role of dihydroxybenzenes and oxygen on the corrosion of steel in black liquor. Corrosion Science. https://doi.org/10.1016/0010-938x(96)00186-2
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.