The DOI matches its Crossref record; 22 of the 22 references it cites were found in a registry or an index.
Laser powder-bed fusion additive manufacturing: Physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones
Open accessAbstract
Abstract This study demonstrates the significant effect of the recoil pressure and Marangoni convection in laser powder bed fusion (L-PBF) of 316L stainless steel. A three-dimensional high fidelity powder-scale model reveals how the strong dynamical melt flow generates pore defects, material spattering (sparking), and denudation zones. The melt track is divided into three sections: a topological depression, a transition and a tail region, each being the location of specific physical effects. The inclusion of laser ray-tracing energy deposition in the powder-scale model improves over traditional volumetric energy deposition. It enables partial particle melting, which impacts pore defects in the denudation zone. Different pore formation mechanisms are observed at the edge of a scan track, at the melt pool bottom (during collapse of the pool depression), and at the end of the melt track (during laser power ramp down). Remedies to these undesirable pores are discussed. The results are validated against the experiments and the sensitivity to laser absorptivity is discussed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
3-D printing: The new industrial revolution
Berman, B. (2012) · Business Horizons · doi:10.1016/j.bushor.2011.11.003 · Cited by 2,481
Thijs, L., Kempen, K., Kruth, J.-P., & Van Humbeeck, J. (2013) · Acta Materialia · doi:10.1016/j.actamat.2012.11.052 · Cited by 1,917
Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing
King, W. E., Barth, H. D., Castillo, V. M., Gallegos, G. F., Gibbs, J. W., Hahn, D. E., Kamath, C., & Rubenchik, A. M. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.06.005 · Cited by 1,616
Self-citationConsolidation phenomena in laser and powder-bed based layered manufacturing
Kruth, J.-P., Levy, G., Klocke, F., & Childs, T. H. C. (2007) · CIRP Annals · doi:10.1016/j.cirp.2007.10.004 · Cited by 1,444
King, W. E., Anderson, A. T., Ferencz, R. M., Hodge, N. E., Kamath, C., Khairallah, S. A., & Rubenchik, A. M. (2015) · Applied Physics Reviews · doi:10.1063/1.4937809 · Cited by 1,258
Self-citationQiu, C., Panwisawas, C., Ward, R., Basoalto, H., Brooks, J. W., & Attallah, M. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.06.004 · Cited by 1,041
Single track formation in selective laser melting of metal powders
Yadroitsev, I., Gusarov, A., Yadroitsava, I., & Smurov, I. (2010) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.05.010 · Cited by 827
Qiu, C., Adkins, N. J. E., & Attallah, M. M. (2013) · Materials Science and Engineering: A · doi:10.1016/j.msea.2013.04.099 · Cited by 821
Mesoscopic simulation model of selective laser melting of stainless steel powder
Khairallah, S. A., & Anderson, A. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.06.001 · Cited by 616
Self-citationRai, R., Elmer, J. W., Palmer, T. A., & DebRoy, T. (2007) · Journal of Physics D Applied Physics · doi:10.1088/0022-3727/40/18/037 · Cited by 473
Mesoscopic simulation of selective beam melting processes
Körner, C., Attar, E., & Heinl, P. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.12.016 · Cited by 450
Yuan, P., & Gu, D. (2015) · Journal of Physics D Applied Physics · doi:10.1088/0022-3727/48/3/035303 · Cited by 345
Schoinochoritis, B., Chantzis, D., & Salonitis, K. (2015) · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · doi:10.1177/0954405414567522 · Cited by 341
Fundamental consolidation mechanisms during selective beam melting of powders
Körner, C., Bauereiß, A., & Attar, E. (2013) · Modelling and Simulation in Materials Science and Engineering · doi:10.1088/0965-0393/21/8/085011 · Cited by 323
Modeling the interaction of laser radiation with powder bed at selective laser melting
Gusarov, A. V., & Smurov, I. Y. (2010) · Physics Procedia · doi:10.1016/j.phpro.2010.08.065 · Cited by 284
Modelling of radiation transfer in metallic powders at laser treatment
Gusarov, A. V., & Kruth, J.-P. (2005) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2005.01.044 · Cited by 227
3D-imaging of selective laser melting defects in a Co–Cr–Mo alloy by synchrotron radiation micro-CT
Zhou, X., Wang, D., Liu, X., Zhang, D., Qu, S., Ma, J., London, G., Shen, Z., & Liu, W. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.07.014 · Cited by 216
Simulation of Laser Beam Melting of Steel Powders using the Three-Dimensional Volume of Fluid Method
Gürtler, F.-J., Karg, M., Leitz, K.-H., & Schmidt, M. (2013) · Physics Procedia · doi:10.1016/j.phpro.2013.03.162 · Cited by 165
In situ flaw detection by IR‐imaging during electron beam melting
Schwerdtfeger, J., Singer, R. F., & Körner, C. (2012) · Rapid Prototyping Journal · doi:10.1108/13552541211231572 · Cited by 139
Modelling of electron beam absorption in complex geometries
Klassen, A., Bauereiß, A., & Körner, C. (2014) · Journal of Physics D Applied Physics · doi:10.1088/0022-3727/47/6/065307 · Cited by 107
Lattice Boltzmann model for thermal free surface flows with liquid–solid phase transition
Attar, E., & Körner, C. (2010) · International Journal of Heat and Fluid Flow · doi:10.1016/j.ijheatfluidflow.2010.09.006 · Cited by 100
Cited by
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Additively manufactured hierarchical stainless steels with high strength and ductility
Wang, Y. M., Voisin, T., McKeown, J. T., Ye, J., Calta, N. P., Li, Z., Zeng, Z., Zhang, Y., Chen, W., Roehling, T. T., et al. (2018) · Nature Materials · doi:10.1038/nmat5021 · Cited by 2,613
Metal additive manufacturing in aerospace: A review
Blakey-Milner, B., Gradl, P., Snedden, G., Brooks, M., Pitot, J., Lopez, E., Leary, M., Berto, F., & du Plessis, A. (2021) · Materials & Design · doi:10.1016/j.matdes.2021.110008 · Cited by 2,263
Material-structure-performance integrated laser-metal additive manufacturing
Gu, D., Shi, X., Poprawe, R., Bourell, D. L., Setchi, R., & Zhu, J. (2021) · Science · doi:10.1126/science.abg1487 · Cited by 1,703
Svetlizky, D., Das, M., Zheng, B., Vyatskikh, A. L., Bose, S., Bandyopadhyay, A., Schoenung, J. M., Lavernia, E. J., & Eliaz, N. (2021) · Materials Today · doi:10.1016/j.mattod.2021.03.020 · Cited by 1,371
Metadata
- Authors
- Khairallah, S. A., Anderson, A. T., Rubenchik, A., & King, W. E.
- Venue
- Acta Materialia
- Publisher
- Elsevier BV
- Published
- 2016-04
- Volume
- 108
- Pages
- 36-45
- ISSN
- 1359-6454 (ISSN-L)
- OpenAlex
- W2279780730
- Cited by
- 2,766
- References
- 22
- FWCI
- 161.43
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.