The DOI matches its Crossref record; 24 of the 24 references it cites were found in a registry or an index.
Heterogeneous precipitation behavior and stacking-fault-mediated deformation in a CoCrNi-based medium-entropy alloy
Open accessAbstract
Abstract Combining high strength and good ductility is highly-desired yet challenging for conventional structural materials. Newly emerging concentrated multi-component alloys with face-centered-cubic structure provide an ultra-ductile matrix, and the precipitation hardening based on these alloys provides a very effective way to achieve a superior strength-ductility combination. Here, we report a high-strength CoCrNi-based medium-entropy alloy hardened by nanoscale L1 2 -(Ni, Co, Cr) 3 (Ti, Al)-type particles with mixing heterogeneous and homogeneous precipitation behaviors. Compared to the single-phase CoCrNi medium-entropy alloy, the yield strength and the tensile strength of the precipitation-strengthened CoCrNi medium-entropy alloy were increased by ∼70% to ∼750 MPa and ∼44% to ∼1.3 GPa, respectively, whereas a good ductility, ∼45%, was still achieved. The underlying deformation micro-mechanisms were systematically investigated using transmission electron microscope. In the single-phase CoCrNi medium-entropy alloy, the deformation mode was dominated by mechanical twinning. In the precipitation-hardened medium-entropy alloy, however, a high density of stacking faults prevailed. We revealed that the absence of mechanical twinning in this low stacking fault energy precipitation-strengthened medium-entropy alloy could relate to the increasing critical twinning stress affected by the channel width of the matrix. We further calculated that the increment of the yield strength was substantially from precipitation strengthening. Our present findings provide not only a fundamental understanding of the deformation micro-mechanism of the precipitation-strengthened CoCrNi medium-entropy alloy but also a useful guidance for the development of precipitation-hardened concentrated multi-component alloys in the future.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A critical review of high entropy alloys and related concepts
Miracle, D. B., & Senkov, O. N. (2017) · Acta Materialia · doi:10.1016/j.actamat.2016.08.081 · Cited by 8,973
A fracture-resistant high-entropy alloy for cryogenic applications
Gludovatz, B., Hohenwarter, A., Catoor, D., Chang, E. H., George, E. P., & Ritchie, R. O. (2014) · Science · doi:10.1126/science.1254581 · Cited by 5,714
Thermo-Calc & DICTRA, computational tools for materials science
Andersson, J.-O., Helander, T., Höglund, L., Shi, P., & Sundman, B. (2002) · Calphad · doi:10.1016/s0364-5916(02)00037-8 · Cited by 4,322
Metastable high-entropy dual-phase alloys overcome the strength–ductility trade-off
Li, Z., Pradeep, K. G., Deng, Y., Raabe, D., & Tasan, C. C. (2016) · Nature · doi:10.1038/nature17981 · Cited by 4,071
The Superalloys: Fundamentals and Applications
Reed, R. C. (2008) · Cited by 3,725
Rayleigh, L. (1878) · Proceedings of the London Mathematical Society · doi:10.1112/plms/s1-10.1.4 · Cited by 3,064
High-entropy alloy: challenges and prospects
Ye, Y. F., Wang, Q., Lu, J., Liu, C. T., & Yang, Y. (2016) · Materials Today · doi:10.1016/j.mattod.2015.11.026 · Cited by 3,016
Self-citationWu, Z., Bei, H., Pharr, G. M., & George, E. P. (2014) · Acta Materialia · doi:10.1016/j.actamat.2014.08.026 · Cited by 2,134
Exceptional damage-tolerance of a medium-entropy alloy CrCoNi at cryogenic temperatures
Gludovatz, B., Hohenwarter, A., Thurston, K. V. S., Bei, H., Wu, Z., George, E. P., & Ritchie, R. O. (2016) · Nature Communications · doi:10.1038/ncomms10602 · Cited by 1,930
Laplanche, G., Kostka, A., Reinhart, C., Hunfeld, J., Eggeler, G., & George, E. P. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.02.036 · Cited by 1,379
Microstructure evolution and critical stress for twinning in the CrMnFeCoNi high-entropy alloy
Laplanche, G., Kostka, A., Horst, O. M., Eggeler, G., & George, E. P. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.038 · Cited by 1,198
Ductile CoCrFeNiMox high entropy alloys strengthened by hard intermetallic phases
Liu, W. H., Lu, Z. P., He, J. Y., Luan, J. H., Wang, Z. J., Liu, B., Liu, Y., Chen, M. W., & Liu, C. T. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.06.063 · Cited by 1,064
Self-citationHigh-entropy alloys: a critical assessment of their founding principles and future prospects
Pickering, E. J., & Jones, N. G. (2016) · International Materials Reviews · doi:10.1080/09506608.2016.1180020 · Cited by 1,062
Creep resistance of CMSX-3 nickel base superalloy single crystals
Pollock, T. M., & Argon, A. S. (1992) · Acta Metallurgica et Materialia · doi:10.1016/0956-7151(92)90195-k · Cited by 1,000
Stacking fault energies and slip in nanocrystalline metals
Van Swygenhoven, H., Derlet, P. M., & Frøseth, A. G. (2004) · Nature Materials · doi:10.1038/nmat1136 · Cited by 997
Curtze, S., & Kuokkala, V.-T. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.05.049 · Cited by 866
On the origin of planar slip in f.c.c. alloys
Gerold, V., & Karnthaler, H. P. (1989) · Acta Metallurgica · doi:10.1016/0001-6160(89)90143-0 · Cited by 853
Lu, C., Niu, L., Chen, N., Jin, K., Yang, T., Xiu, P., Zhang, Y., Gao, F., Bei, H., Shi, S., et al. (2016) · Nature Communications · doi:10.1038/ncomms13564 · Cited by 822
Self-citationThe determination of yield strength from hardness measurements
Cahoon, J. R., Broughton, W. H., & Kutzak, A. R. (1971) · Metallurgical Transactions · doi:10.1007/bf02913433 · Cited by 793
Strengthening Mechanisms in Polycrystalline Multimodal Nickel-Base Superalloys
Kozar, R. W., Suzuki, A., Milligan, W. W., Schirra, J. J., Savage, M. F., & Pollock, T. M. (2009) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-009-9858-5 · Cited by 707
Zhang, Z., Sheng, H., Wang, Z., Gludovatz, B., Zhang, Z., George, E. P., Yu, Q., Mao, S. X., & Ritchie, R. O. (2017) · Nature Communications · doi:10.1038/ncomms14390 · Cited by 664
Zhang, Y. H., Zhuang, Y., Hu, A., Kai, J. J., & Liu, C. T. (2017) · Scripta Materialia · doi:10.1016/j.scriptamat.2016.11.014 · Cited by 313
Self-citationPhase stability of non-equiatomic CoCrFeMnNi high entropy alloys
Ma, D., Yao, M., Pradeep, K. G., Tasan, C. C., Springer, H., & Raabe, D. (2015) · Acta Materialia · doi:10.1016/j.actamat.2015.07.030 · Cited by 262
Phase stability and tensile properties of Co-free Al0.5CrCuFeNi2 high-entropy alloys
Ng, C., Guo, S., Luan, J., Wang, Q., Lu, J., Shi, S., & Liu, C. T. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2013.09.105 · Cited by 175
Self-citation
Cited by
George, E. P., Raabe, D., & Ritchie, R. O. (2019) · Nature Reviews Materials · doi:10.1038/s41578-019-0121-4 · Cited by 5,047
Mechanical behavior of high-entropy alloys
Li, W., Xie, D., Li, D., Zhang, Y., Gao, Y., & Liaw, P. K. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100777 · Cited by 1,321
Li, Q.-J., Sheng, H., & Ma, E. (2019) · Nature Communications · doi:10.1038/s41467-019-11464-7 · Cited by 795
High-entropy alloys with heterogeneous microstructure: Processing and mechanical properties
Sathiyamoorthi, P., & Kim, H. S. (2022) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100709 · Cited by 766
Du, X. H., Li, W. P., Chang, H. T., Yang, T., Duan, G. S., Wu, B. L., Huang, J. C., Chen, F. R., Liu, C. T., Chuang, W. S., et al. (2020) · Nature Communications · doi:10.1038/s41467-020-16085-z · Cited by 558
Self-citation
Metadata
- Authors
- Zhao, Y. L., Yang, T., Tong, Y., Wang, J., Luan, J. H., Jiao, Z. B., Chen, D., Yang, Y., Hu, A., Liu, C. T., & Kai, J.-J.
- Venue
- Acta Materialia
- Publisher
- Elsevier BV
- Published
- 2017-10
- Volume
- 138
- Pages
- 72-82
- ISSN
- 1359-6454 (ISSN-L)
- OpenAlex
- W2734956595
- Cited by
- 998
- References
- 24
- FWCI
- 33.76
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.