Student or educator? Sign up with your school email and get 6 months of Pro free.
Cited by 609

The DOI matches its Crossref record; 17 of the 17 references it cites were found in a registry or an index.

Current progress and future challenges in rare-earth-free permanent magnets

Open access
Cui, Jun, Kramer, Matthew, Zhou, Lin, Liu, Fei, Gabay, Alexander, Hadjipanayis, George, Balasubramanian, Balamurugan, Sellmyer, David·2018·Acta Materialia

Abstract

Permanent magnets (PM) are critical components for electric motors and power generators. Key properties of permanent magnets, especially coercivity and remanent magnetization, are strongly dependent on microstructure. Understanding metallurgical processing, phase stability and microstructural changes are essential for designing and improving permanent magnets. The widely used PM for the traction motor in electric vehicles and for the power generator in wind turbines contain rare earth elements Nd and Dy due to their high maximum energy product. Dy is used to sustain NdFeB's coercivity at higher temperature. Due to the high supply risk of rare earth elements (REE) such as Dy and Nd, these elements are listed as critical materials by the U.S. Department of Energy and other international institutes. Other than Dy, finer grain size is also found to have effect on sustaining coercivity at higher temperature. A proper control of phase stability and microstructures has direct impact on mitigating REE supply risk. Compared to rare earth PMs, non-rare earth (non-RE) PMs typically have lower maximum energy products, however, given their small supply risks and low cost, they are being intensively investigated for less-demanding applications. The general goal for the development of non-RE PMs is to fill in the gap between the most cost-effective but low performing hard ferrite magnet and the most expensive but high performing RE PMs. In the past five years great progress has been made toward improving the microstructure and physical properties of non-RE PMs. Several new candidate materials systems were investigated, and some have showed realistic potential for replacing RE PMs for some applications. In this article, we review the science and technology of various types of non-RE materials for PM applications. These materials systems include Mn based, high magnetocrystalline anisotropy alloys (MnBi and MnAl compounds), spinodally decomposing alloys (Alnico), high-coercivity tetrataenite L10 phase (FeNi and FeCo), and nitride/carbide systems (such as α" based, high saturation magnetization Fe16N2 type phase and Co2C/Co3C acicular particle phase). The current status, challenges, potentials as well as the future directions for these candidates non-RE magnet materials are discussed.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1016/j.actamat.2018.07.049

Cites

17 of 17 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 17 references

Cited by

See all 609

Metadata

Authors
Cui, J., Kramer, M., Zhou, L., Liu, F., Gabay, A., Hadjipanayis, G., Balasubramanian, B., & Sellmyer, D.
Venue
Acta Materialia
Publisher
Elsevier BV
Published
2018-10
Volume
158
Pages
118-137
ISSN
1359-6454 (ISSN-L)
OpenAlex
W2883026210
Cited by
609
References
17
FWCI
13.62
Type
journal article
Language
en
Open access
hybrid

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Current progress and future challenges in rare-earth-free permanent magnets. https://app.cochat.ai/papers/10.1016/j.actamat.2018.07.049
The paper
Cui, J., Kramer, M., Zhou, L., Liu, F., Gabay, A., Hadjipanayis, G., Balasubramanian, B., & Sellmyer, D. (2018). Current progress and future challenges in rare-earth-free permanent magnets. Acta Materialia. https://doi.org/10.1016/j.actamat.2018.07.049

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.