Student or educator? Sign up with your school email and get 6 months of Pro free.
CoChat
Cited by 170

The DOI matches its Crossref record; 3 of the 3 references it cites were found in a registry or an index.

Effect of biomass type, heating rate, and sample size on microwave-enhanced fast pyrolysis product yields and qualities

Open access
Klinger, Jordan L., Westover, Tyler L., Emerson, Rachel M., Williams, C. Luke, Hernandez, Sergio, Monson, Glen D., Ryan, J. Chadron · 2018 · Applied Energy

Abstract

The products from fast pyrolysis of biomass are variable and highly dependent upon feedstock composition, particle size and geometry, and operating conditions such as heating rate, reaction temperature, and sweep gas composition and velocity. Microwave heating is internal to the biomass particles, thereby avoiding convective and conductive heat transfer limitations, which facilitates decoupling heat transfer effects from chemical reaction kinetics. This separation allows for elucidation of the primary effects of the original materials’ composition on product yields. To better understand the interconnectedness of biomass composition and fast pyrolysis (pyrolysis liquid oil yield in particular), a high throughput microwave-enhanced fast pyrolysis (MEFP) reactor was used to react 33 biomass samples with a minimum of three replicate tests each. The materials in this study included: woody feedstocks (with and without bark), agricultural residues, herbaceous energy crops, and blended feedstocks. The highest liquid yields were obtained from lumber (66.2 wt%) and tulip poplar (64.9 wt%), while the lowest yields were obtained from sorghum (47.8 wt%) and single-pass harvested corn stover (48.5 wt%). Liquid yields had an average standard deviation of 1.4 wt% (average 2.5% relative standard deviation). The MEFP achieved heating rates up to 200 °C/s, however, beyond 10 °C/s liquid oil plateaued with increasing heating rate. Multivariate regression of pyrolysis yields with over 20 feedstock properties, obtained through detailed compositional analysis, indicates that aggregated alkali and alkaline Earth metals (primarily K and Na, along with Ca and Mg) accounted for the most variability among liquid yields (R2 = 0.71). Addition of volatile matter as a second predictor variable achieved the greatest reduction of the model residuals to increase the coefficient of regression (R2) to 0.85. Liquid yield water fraction increased linearly with feedstock potassium and sodium content over a much wider range than previously observed. Pyrolysis oil acid content was found to increase with increasing volatile matter and decreasing potassium and sodium content.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1016/j.apenergy.2018.06.107

Cites

3 of 3 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 3 references

Cited by

See all 170

Metadata

Authors
Klinger, J. L., Westover, T. L., Emerson, R. M., Williams, C. L., Hernandez, S., Monson, G. D., & Ryan, J. C.
Venue
Applied Energy
Publisher
Elsevier BV
Published
2018-10
Volume
228
Pages
535-545
ISSN
0306-2619 (ISSN-L)
OpenAlex
W2866573893
Cited by
170
References
3
FWCI
6.13
Type
journal article
Language
en
Open access
hybrid

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Effect of biomass type, heating rate, and sample size on microwave-enhanced fast pyrolysis product yields and qualities. https://app.cochat.ai/papers/10.1016/j.apenergy.2018.06.107
The paper
Klinger, J. L., Westover, T. L., Emerson, R. M., Williams, C. L., Hernandez, S., Monson, G. D., & Ryan, J. C. (2018). Effect of biomass type, heating rate, and sample size on microwave-enhanced fast pyrolysis product yields and qualities. Applied Energy. https://doi.org/10.1016/j.apenergy.2018.06.107

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.