The DOI matches its Crossref record; 49 of the 49 references it cites were found in a registry or an index.
Sustainable use of red mud in ultra-high performance concrete (UHPC): Design and performance evaluation
Abstract
This paper presents an efficient application for red mud, i.e., recycling red mud as a mineral additive in the development of ultra-high performance concrete (UHPC). Specifically, the modified Andreasen & Andersen particle packing model has been carried out to obtain a densely compacted UHPC matrix. After that, red mud is used to replace cement to reduce both the landfilling of red mud and the environmental burden of UHPC. Then, the fresh and hardened behavior of UHPC with and without red mud has been evaluated. It has been found that the addition of red mud enhanced early-age (7 d) durability due to the accelerated hydration process, while reduced the workability and the mechanical properties of UHPC. The degraded workability may affect the application in the building with complex shapes, but it can still be applied in general construction. An ultra-high strength (>150 MPa) of UHPC including 40% red mud can be generated after high-temperature curing, although the addition of red mud reduces the compressive strength. Besides, it is noteworthy that significantly shortened setting time can be obtained when replacing cement by red mud, providing ideas for the application in the UHPC rapid-repairing process. The pore structure analysis reveals a coarsening of micro-pore structure with an increase of red mud content. Finally, a low-energy consumption, as well as low radiation risk further promotes the environmental protection application of red mud based UHPC.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Supplementary cementitious materials
Lothenbach, B., Scrivener, K., & Hooton, R. D. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2010.12.001 · Cited by 3,406
A Practical Guide to Microstructural Analysis of Cementitious Materials
(2018) · CRC Press eBooks · doi:10.1201/b19074 · Cited by 2,110
A review on ultra high performance concrete: Part I. Raw materials and mixture design
Shi, C., Wu, Z., Xiao, J., Wang, D., Huang, Z., & Fang, Z. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.10.088 · Cited by 1,392
Mix design and properties assessment of Ultra-High Performance Fibre Reinforced Concrete (UHPFRC)
Yu, R., Spiesz, P., & Brouwers, H. J. H. (2014) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.11.002 · Cited by 1,149
Self-citationSynthesis and characterization of red mud and rice husk ash-based geopolymer composites
He, J., Jie, Y., Zhang, J., Yu, Y., & Zhang, G. (2013) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2012.11.010 · Cited by 770
Yu, R., Spiesz, P., & Brouwers, H. J. H. (2015) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2014.09.024 · Cited by 704
Self-citationHabel, K., Viviani, M., Denarié, E., & Brühwiler, E. (2006) · Cement and Concrete Research · doi:10.1016/j.cemconres.2006.03.009 · Cited by 647
Wang, S., Ang, H. M., & Tadé, M. O. (2008) · Chemosphere · doi:10.1016/j.chemosphere.2008.05.013 · Cited by 567
Packing density of cementitious materials: part 1—measurement using a wet packing method
Wong, H. H. C., & Kwan, A. K. H. (2008) · Materials and Structures · doi:10.1617/s11527-007-9274-5 · Cited by 556
The History, Challenges, and New Developments in the Management and Use of Bauxite Residue
Evans, K. (2016) · Journal of Sustainable Metallurgy · doi:10.1007/s40831-016-0060-x · Cited by 487
Lawrence, P., Cyr, M., & Ringot, E. (2003) · Cement and Concrete Research · doi:10.1016/s0008-8846(03)00183-2 · Cited by 476
Ghafari, E., Costa, H., Júlio, E., Portugal, A., & Durães, L. (2014) · Materials & Design · doi:10.1016/j.matdes.2014.02.051 · Cited by 469
Red mud addition in the raw meal for the production of Portland cement clinker
Tsakiridis, P. E., Agatzini-Leonardou, S., & Oustadakis, P. (2004) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2004.08.002 · Cited by 445
Nanogranular packing of C–S–H at substochiometric conditions
Vandamme, M., Ulm, F.-J., & Fonollosa, P. (2010) · Cement and Concrete Research · doi:10.1016/j.cemconres.2009.09.017 · Cited by 409
Huang, W., Kazemi-Kamyab, H., Sun, W., & Scrivener, K. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2016.12.009 · Cited by 404
A review of the characterization and revegetation of bauxite residues (Red mud)
Xue, S., Zhu, F., Kong, X., Wu, C., Huang, L., Huang, N., & Hartley, W. (2016) · Environmental Science and Pollution Research · doi:10.1007/s11356-015-4558-8 · Cited by 395
Preparation of Ultra-High Performance Concrete with common technology and materials
Wang, C., Yang, C., Liu, F., Wan, C., & Pu, X. (2012) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2011.11.005 · Cited by 391
Development of paving blocks from synergistic use of red mud and fly ash using geopolymerization
Kumar, A., & Kumar, S. (2012) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2012.09.013 · Cited by 385
Explanations for the cause of shear thickening in concentrated colloidal suspensions
Hoffman, R. L. (1998) · Journal of Rheology · doi:10.1122/1.550884 · Cited by 382
The study of using rice husk ash to produce ultra high performance concrete
Van Tuan, N., Ye, G., van Breugel, K., Fraaij, A. L. A., & Bui, D. D. (2011) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2010.11.046 · Cited by 379
Environmental assessment, management and utilization of red mud in China
Liu, W., Chen, X., Li, W., et al. (2014) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2014.06.080 · Cited by 376
Rheological properties of ultra-high-performance concrete — An overview
Khayat, K. H., Meng, W., Vallurupalli, K., & Teng, L. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.105828 · Cited by 376
Li, Y., Min, X., Ke, Y., Liu, D., & Tang, C. (2019) · Waste Management · doi:10.1016/j.wasman.2018.11.019 · Cited by 367
Development of ultra-high-performance concrete using glass powder – Towards ecofriendly concrete
Soliman, N. A., & Tagnit-Hamou, A. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.08.073 · Cited by 343
Role of carbonates in the chemical evolution of sodium carbonate-activated slag binders
Bernal, S. A., Provis, J. L., Myers, R. J., San Nicolas, R., & van Deventer, J. S. J. (2015) · Materials and Structures · doi:10.1617/s11527-014-0412-6 · Cited by 334
Yazıcı, H. (2007) · Building and Environment · doi:10.1016/j.buildenv.2006.03.013 · Cited by 312
Mehdipour, I., & Khayat, K. H. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.01.005 · Cited by 299
Mechanical and microstructural characterization of geopolymers derived from red mud and fly ashes
Hu, W., Nie, Q., Huang, B., Shu, X., & He, Q. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.03.086 · Cited by 274
High performance concrete—An overview
Neville, A., & Aïtcin, P.-C. (1998) · Materials and Structures · doi:10.1007/bf02486473 · Cited by 272
Mix design of UHPFRC and its response to projectile impact
Máca, P., Sovják, R., & Konvalinka, P. (2014) · International Journal of Impact Engineering · doi:10.1016/j.ijimpeng.2013.08.003 · Cited by 230
Synthesis and characterization of geopolymers derived from coal gangue, fly ash and red mud
Koshy, N., Dondrob, K., Hu, L., Wen, Q., & Meegoda, J. N. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.02.076 · Cited by 212
Zhang, H., Ji, T., Zeng, X., Yang, Z., Lin, X., & Liang, Y. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.10.117 · Cited by 188
Wang, Y., Zhang, T.-A., Lyu, G., Guo, F., Zhang, W., & Zhang, Y. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.04.009 · Cited by 187
Self-citationLimestone reaction in calcium aluminate cement–calcium sulfate systems
Bizzozero, J., & Scrivener, K. L. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.05.019 · Cited by 177
Ghalehnovi, M., Roshan, N., Hakak, E., Shamsabadi, E. A., & de Brito, J. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.118213 · Cited by 155
Yang, Z., Mocadlo, R., Zhao, M., Sisson, R. D., Tao, M., & Liang, J. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.06.034 · Cited by 149
Mixture-proportioning of economical UHPC mixtures
Alsalman, A., Dang, C. N., Martí‐Vargas, J. R., & Hale, W. M. (2019) · Journal of Building Engineering · doi:10.1016/j.jobe.2019.100970 · Cited by 146
Utilization of ferroalumina as raw material in the production of Ordinary Portland Cement
Vangelatos, I., Angelopoulos, G. N., & Boufounos, D. (2009) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2009.02.049 · Cited by 142
Nanoscale mechanism of ions immobilized by the geopolymer: A molecular dynamics study
Hou, D., Zhang, J., Pan, W., Zhang, Y., & Zhang, Z. (2019) · Journal of Nuclear Materials · doi:10.1016/j.jnucmat.2019.151841 · Cited by 123
Self-citationPreparation and mechanism of the sintered bricks produced from Yellow River silt and red mud
He, H., Yue, Q., Su, Y., Gao, B., Gao, Y., Wang, J., & Yu, H. (2011) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2011.11.095 · Cited by 118
Li, P., Brouwers, H. J. H., & Yu, Q. (2019) · International Journal of Impact Engineering · doi:10.1016/j.ijimpeng.2019.103434 · Cited by 113
Makita, T., & Brühwiler, E. (2013) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2013.09.004 · Cited by 111
Preparation of high porosity bricks by utilizing red mud and mine tailing
Kim, Y., Lee, Y., Kim, M., & Park, H. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.10.044 · Cited by 107
Effects of red mud on properties of self-compacting mortar
Liu, R., & Poon, C. S. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2016.07.052 · Cited by 98
Laboratory production of calcium sulfoaluminate cements with high industrial waste content
Canbek, O., Shakouri, S., & Erdoğan, S. T. (2019) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2019.103475 · Cited by 95
Bayer-geopolymers: An exploration of synergy between the alumina and geopolymer industries
van Riessen, A., Jamieson, E., Kealley, C. S., Hart, R. D., & Williams, R. P. (2013) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2013.04.010 · Cited by 90
Self-compacting architectural concrete production using red mud
Ghalehnovi, M., Shamsabadi, E. A., Khodabakhshian, A., Sourmeh, F., & de Brito, J. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.07.248 · Cited by 86
COMPACT REINFORCED COMPOSITE BASIC PRINCIPLES.
Bache, H. H. (1987) · Cited by 33
Recent trends in alumina and aluminium production technology
Mahadevan, H., & Ramachandran, T. (1996) · Bulletin of Materials Science · doi:10.1007/bf02744627 · Cited by 18
Cited by
Sharma, R., Jang, J. G., & Bansal, P. P. (2022) · Journal of Building Engineering · doi:10.1016/j.jobe.2021.103314 · Cited by 181
Liu, Z., Kong, D., Wang, L., Liu, A., Xu, F., Fang, Z., & Wang, S. (2025) · Journal of Building Engineering · doi:10.1016/j.jobe.2025.113879 · Cited by 7
Metadata
- Authors
- Hou, D., Wu, D., Wang, X., Gao, S., Yu, R., Li, M., Wang, P., & Wang, Y.
- Venue
- Cement and Concrete Composites
- Publisher
- Elsevier BV
- Published
- 2021-01
- Volume
- 115
- Pages
- 103862
- ISSN
- 0958-9465 (ISSN-L)
- OpenAlex
- W3096421631
- Cited by
- 260
- References
- 49
- FWCI
- 15.73
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.