Student or educator? Sign up with your school email and get 6 months of Pro free.
CoChat
Cited by 185

The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.

DEM-CFD coupling simulation and optimization of an inside-filling air-blowing maize precision seed-metering device

Han, Dandan, Zhang, Dongxing, Jing, Huirong, Yang, Li, Cui, Tao, Ding, Youqiang, Wang, Zhendong, Wang, Yunxia, Zhang, Tianliang · 2018 · Computers and Electronics in Agriculture

Abstract

Abstract Simulation of the gas-solid flow in an inside-filling air-blowing maize precision seed-metering device was performed by means of a coupling approach of the discrete element method (DEM) and computational fluid dynamics (CFD). In this model, EDEM software was used to depict the discrete particle phase, and ANSYS Fluent software was used to describe the continuous gas phase. Maize particles were created by EDEM software using the bonded particle model (BPM) to define a single structure of the particles. Effects of the positions, the width and the average arc length of the lateral hole were examined and analyzed in terms of gas field and seed movement. Using an orthogonal experimental design, the primary and secondary factors and parameters of the maximum evaluation index affecting the working performance of a seed-metering device were assessed. The superiority of a lower position of the lateral hole was identified, as both the width and the average arc length of the lateral hole had no effect on the drag force or differential pressure. The area of the lateral hole significantly affected the movement and airflow field of seeds in the hole of a seed-metering device. The drag force, the differential pressure and the pressure loss increase with the expansion of the area of the lateral hole also resulted in a decrease in the upper pressure. The optimized lateral hole, which is 1.5 mm wide and has an average arc length of 10 mm when the position is lower, had a good working performance, with less pressure loss, superior drag force and differential pressure. The qualified rate of the optimized seed-metering device was greater than 93% when the working pressure was above 5.5 kPa with a working speed lower than 10 km/h through experiment. The results showed that the DEM-CFD coupling approach was a reliable instrument for simulating the physical phenomenon of seed movement in the airflow field. DEM-CFD coupling simulation of seed movement can provide a theoretical basis for assessment of the potential working performance of an inside-filling air-blowing seed-metering device.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1016/j.compag.2018.05.006

Cites

1 of 1 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Cited by

See all 185

Metadata

Authors
Han, D., Zhang, D., Jing, H., Yang, L., Cui, T., Ding, Y., Wang, Z., Wang, Y., & Zhang, T.
Venue
Computers and Electronics in Agriculture
Publisher
Elsevier BV
Published
2018-07
Volume
150
Pages
426-438
ISSN
0168-1699 (ISSN-L)
OpenAlex
W2808214516
Cited by
185
References
1
FWCI
4.80
Type
journal article
Language
en
Open access
closed

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.