The DOI matches its Crossref record.
Hybrid effect of macro and micro steel fibers on the pullout and tensile behaviors of ultra-high-performance concrete
Abstract
This study aims to investigate the effect of hybrid use of macro and micro steel fibers on the pullout and tensile behaviors of ultra-high-performance concrete (UHPC). To this end, three different macro steel fibers (i.e., straight, hooked, and twisted fibers) and a single micro straight steel fiber were used, whereby a portion of the macro fibers was replaced with the micro fibers at the constant total volume fraction of 2%. In order to fabricate ultra-high-performance hybrid fiber-reinforced concrete (UHP–HFRC), five different replacement ratios of the macro fibers with the micro fiber were employed, including 0, 0.5, 1.0, 1.5, and 2.0%. The pullout behaviors of multiple aligned fibers embedded in UHPC were also compared with the tensile behaviors of UHP–HFRC to analyze their correlations. The test results indicated that the average bond strength and normalized pullout energy of the macro straight fibers in UHPC were improved after their replacement with micro fibers, whereas those of the hooked and twisted macro fibers were reduced according to the replacement ratio. Lower fiber efficiency ratios were obtained after the replacement of the macro fibers with the micro fibers in the hooked and twisted fiber cases, while similar ratios of approximately 0.3–0.4 were obtained in the cases of the macro straight fibers. In comparison, the post cracking tensile strength and energy absorption capacity of UHPC reinforced with macro straight fibers decreased, whereas those of UHPCs with hooked and twisted fibers increased when they were replaced by the micro fibers. The negative correlation between fiber pullout and tensile behaviors of all UHP–HFRCs occurred because the actual fiber orientation and bonding area in the composites could not be considered in the fiber pullout tests. Thus, it is concluded that the effects of the use of hybrid steel fibers on the tensile performance of the UHPC composites could not be predicted based on the pullout test results of the aligned fibers.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
New development of ultra-high-performance concrete (UHPC)
Du, J., Meng, W., Khayat, K. H., Bao, Y., Guo, P., Lyu, Z., Abu-obeidah, A., Nassif, H., & Wang, H. (2021) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2021.109220 · Cited by 1,013
Utilization of fibers in ultra-high performance concrete: A review
Gong, J., Ma, Y., Fu, J., Hu, J., Ouyang, X., Zhang, Z., & Wang, H. (2022) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2022.109995 · Cited by 360
Seawater sea-sand Engineered Geopolymer Composites (EGC) with high strength and high ductility
Lao, J.-C., Huang, B.-T., Xu, L.-Y., Khan, M., Fang, Y., & Dai, J.-G. (2023) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2023.104998 · Cited by 257
Metadata
- Authors
- Chun, B., & Yoo, D.-Y.
- Venue
- Composites Part B: Engineering
- Publisher
- Elsevier BV
- Published
- 2019-04
- Volume
- 162
- Pages
- 344-360
- ISSN
- 1359-8368 (ISSN-L)
- OpenAlex
- W2899890040
- Cited by
- 193
- References
- 0
- FWCI
- 11.00
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Hybrid effect of macro and micro steel fibers on the pullout and tensile behaviors of ultra-high-performance concrete. https://app.cochat.ai/papers/10.1016/j.compositesb.2018.11.026
- The paper
- Chun, B., & Yoo, D.-Y. (2019). Hybrid effect of macro and micro steel fibers on the pullout and tensile behaviors of ultra-high-performance concrete. Composites Part B: Engineering. https://doi.org/10.1016/j.compositesb.2018.11.026
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.