The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Effect of the volume fraction of zirconia suspensions on the microstructure and physical properties of products produced by additive manufacturing
Abstract
OBJECTIVE The objectives of the present study were: (1) to analyze the dispersion and optical properties of suspensions with various volume fractions of zirconia, and (2) to assess the influence of zirconia volume fraction on the microstructure and physical properties of products produced by the additive manufacturing and sintering process. METHODS Zirconia specimens were fabricated by an additive manufacturing technique using a DLP (digital light processing) system. The zirconia suspensions were divided into six groups based on zirconia volume fraction within the range of 48-58vol%. RESULTS The maximum volume fraction of zirconia in suspensions possible for printing was 58vol%. The cure depth of the zirconia suspensions decreased as the volume fraction increased. The cure depth was greater than 100μm after 15s photocuring in all groups. Geometrical overgrowth tended to increase gradually as the volume fraction of zirconia increased within the range of 28.55-36.94%. The 3-point bending strength of the specimens increased as the volume fraction of zirconia in the suspension increased, reaching a maximum value of 674.74±32.35MPa for a volume fraction of 58vol%. Cracks were observed on the surfaces of zirconia specimens and these cracks increased in number as zirconia volume fraction decreased. SIGNIFICANCE In this experiment, the viscosity of zirconia suspensions sharply increased from a volume fraction of 54vol%. Because of the very high viscosity, 58vol% was the maximum volume fraction possible for additive manufacturing. After polymerization, all specimens showed some distortion due to geometrical overgrowth. The maximum 3-point bending strength was 674.74±32.35MPa for a volume fraction of 58vol%. But the maximum strength of sintered zirconia prepared by additive manufacturing is inferior to that of conventionally sintered zirconia.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Odian, G. (2004) · doi:10.1002/047147875x · Cited by 7,158
Cited by
A Review of 3D Printing in Dentistry: Technologies, Affecting Factors, and Applications
Tian, Y., Chen, C., Xu, X., Wang, J., Hou, X., Li, K., Lu, X., Shi, H., Lee, E.-S., & Jiang, H. B. (2021) · Scanning · doi:10.1155/2021/9950131 · Cited by 569
A comprehensive review of the photopolymerization of ceramic resins used in stereolithography
Zakeri, S., Vippola, M., & Levänen, E. (2020) · Additive Manufacturing · doi:10.1016/j.addma.2020.101177 · Cited by 496
3D printing restorative materials using a stereolithographic technique: a systematic review
Della Bona, A., Cantelli, V., Britto, V. T., Collares, K. F., & Stansbury, J. W. (2021) · Dental Materials · doi:10.1016/j.dental.2020.11.030 · Cited by 334
Photopolymerization-based additive manufacturing of ceramics: A systematic review
Rasaki, S. A., Xiong, D., Xiong, S., Su, F., Idrees, M., & Chen, Z. (2021) · Journal of Advanced Ceramics · doi:10.1007/s40145-021-0468-z · Cited by 297
Additive manufacturing of ceramics: Advances, challenges, and outlook
Dadkhah, M., Tulliani, J.-M., Saboori, A., & Iuliano, L. (2023) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2023.07.033 · Cited by 272
Metadata
- Authors
- Jang, K.-J., Kang, J.-H., Fisher, J. G., & Park, S.-W.
- Venue
- Dental Materials
- Publisher
- Elsevier BV
- Published
- 2019-05
- Volume
- 35
- Issue
- 5
- Pages
- e97-e106
- ISSN
- 0109-5641 (ISSN-L)
- OpenAlex
- W2920384555
- Cited by
- 177
- References
- 1
- FWCI
- 7.10
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effect of the volume fraction of zirconia suspensions on the microstructure and physical properties of products produced by additive manufacturing. https://app.cochat.ai/papers/10.1016/j.dental.2019.02.001
- The paper
- Jang, K.-J., Kang, J.-H., Fisher, J. G., & Park, S.-W. (2019). Effect of the volume fraction of zirconia suspensions on the microstructure and physical properties of products produced by additive manufacturing. Dental Materials. https://doi.org/10.1016/j.dental.2019.02.001
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.