The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
3D printed triply periodic minimal surfaces as spacers for enhanced heat and mass transfer in membrane distillation
Abstract
Abstract 3D printing is utilized to create different feed channel spacer designs aimed at enhancing the spacer performance specifically for membrane distillation (MD) application. The novelty is the use of mathematically developed triply periodic minimal surface (TPMS) as feed spacers. Five different TPMS based spacer designs were evaluated and benchmarked against the conventionally used net type spacer. The best performing TPMS spacer topology exhibited 60% higher water flux and 63% higher overall film heat transfer coefficient than the commercial spacer. The TPMS spacer designs also had a significant advantage over the commercial spacer when treating feed with high fouling potential such as brine solution. The advantages of TPMS spacers were the high throughput combined with sustained flux performance over increasing TDS concentrations ranging from 75,000 ppm to 100,000 ppm. The best performing TPMS spacer design was identified to have the highest surface area to volume ratio along with a design structure that caused relatively higher turbulence by disrupting the feed flow. Particle deposition tests were done using microspheres to visualize the impact of TPMS spacer design on dead zone formation. Pearson correlation coefficient showed that particle deposition is strongly correlated to the spacer voidage and its membrane contact area.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Evaluation of 3D Printing and Its Potential Impact on Biotechnology and the Chemical Sciences
Gross, B. C., Erkal, J. L., Lockwood, S. Y., Chen, C., & Spence, D. M. (2014) · Analytical Chemistry · doi:10.1021/ac403397r · Cited by 1,746
Cited by
Multifunctional Mechanical Metamaterials Based on Triply Periodic Minimal Surface Lattices
Al-Ketan, O., & Abu Al-Rub, R. K. (2019) · Advanced Engineering Materials · doi:10.1002/adem.201900524 · Cited by 887
Self-citationFeng, J., Fu, J., Yao, X., & He, Y. (2022) · International Journal of Extreme Manufacturing · doi:10.1088/2631-7990/ac5be6 · Cited by 813
Tang, W., Zhou, H., Zeng, Y., Yan, M., Jiang, C., Yang, P., Li, Q., Li, Z., Fu, J., Huang, Y., et al. (2023) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2022.123642 · Cited by 293
3D printing for membrane separation, desalination and water treatment
Tijing, L. D., Dizon, J. R. C., Ibrahim, I., Nisay, A. R. N., Shon, H. K., & Advincula, R. C. (2020) · Applied Materials Today · doi:10.1016/j.apmt.2019.100486 · Cited by 269
Bernal, P. N., Bouwmeester, M., Madrid‐Wolff, J., Falandt, M., Florczak, S., Rodriguez, N. G., Li, Y., Größbacher, G., Samsom, R., van Wolferen, M., et al. (2022) · Advanced Materials · doi:10.1002/adma.202110054 · Cited by 258
Metadata
- Authors
- Thomas, N., Sreedhar, N., Al-Ketan, O., Rowshan, R., Abu Al-Rub, R. K., & Arafat, H.
- Venue
- Desalination
- Publisher
- Elsevier BV
- Published
- 2018-10
- Volume
- 443
- Pages
- 256-271
- ISSN
- 0011-9164 (ISSN-L)
- OpenAlex
- W2810171128
- Cited by
- 223
- References
- 1
- FWCI
- 6.79
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.