The DOI matches its Crossref record; 29 of the 29 references it cites were found in a registry or an index.
Combustion characteristics, engine performances and emissions of a diesel engine using nanoparticle-diesel fuel blends with aluminium oxide, carbon nanotubes and silicon oxide
Abstract
Abstract This research investigates the effect of nanoparticle-diesel fuel blends on combustion characteristics, performances and exhaust emissions of a four-stroke single-cylinder diesel engine. Three types of nanoparticles employed in this experiment were aluminium oxide, carbon nanotubes and silicon oxide. The nanoparticles were dispersed in a dosage of 25 ppm, 50 ppm and 100 ppm with pure diesel and were labelled as DA25, DA50, DA100 (aluminium oxide blends), DC25, DC50, DC100 (carbon nanotubes blends) and DS25, DS50, DS100 (silicon oxide blends). The ultraviolet-visible spectrophotometer analysis was done for 200 h to quantify the stability of the nanoparticle-diesel fuel blends. The blended fuels were experimentally tested with YANMAR TF120M diesel engine at engine loads of 0%, 25%, 50%, 75% and 100% at a constant 1800 rpm engine speed. The results revealed that the brake specific fuel consumption reduced by up to 19.8% and brake thermal efficiency enhanced by 18.8%. Silicon oxide blends show better results than aluminium oxide blends in many aspects, such as higher combustion pressure, lower brake specific fuel consumption and lower carbon monoxide emissions. Aluminium oxide and silicon oxide show stable blend conditions with 28.1% and 22.0% absorption ratio at 200 h sedimentation time, while carbon nanotube blends were least stable with absorption ratio reducing to less than 30% after 10 h. Combustion analysis of carbon nanotube blends with diesel show that carbon nanotubes have the potential to be further researched as an additive for diesel fuel due to significant combustion improvement in NOx emissions. However, the issue on the stability of carbon nanotube blends must be resolved before its potential can be fully utilized.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
ASME International Mechanical Engineering Congress and Exposition
(2001) · The Journal of the Acoustical Society of America · doi:10.1121/1.4776777 · Cited by 2,619
A Review on Nanofluids: Preparation, Stability Mechanisms, and Applications
Yu, W., & Xie, H. (2012) · Journal of Nanomaterials · doi:10.1155/2012/435873 · Cited by 1,770
Theory and design for mechanical measurements
Figliola, R. S., & Beasley, D. E. (1996) · Measurement Science and Technology · doi:10.1088/0957-0233/7/7/016 · Cited by 1,269
A review of nanofluid stability properties and characterization in stationary conditions
Ghadimi, A., Saidur, R., & Metselaar, H. S. C. (2011) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2011.04.014 · Cited by 1,174
Stability and thermal conductivity characteristics of nanofluids
Hwang, Y., Lee, J. K., Lee, C. H., Jung, Y. M., Cheong, S. I., Lee, C. G., Ku, B. C., & Jang, S. P. (2007) · Thermochimica Acta · doi:10.1016/j.tca.2006.11.036 · Cited by 692
Enhancement of thermal conductivity with carbon nanotube for nanofluids
Liu, M.-S., Ching-Cheng Lin, M., Huang, I.-T., & Wang, C.-C. (2005) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2005.05.005 · Cited by 638
Experimental Investigations on the Effects of Cerium Oxide Nanoparticle Fuel Additives on Biodiesel
Sajith, V., Sobhan, C. B., & Peterson, G. P. (2010) · Advances in Mechanical Engineering · doi:10.1155/2010/581407 · Cited by 480
Sadhik Basha, J., & Anand, R. B. (2014) · Alexandria Engineering Journal · doi:10.1016/j.aej.2014.04.001 · Cited by 349
Arul Mozhi Selvan, V., Anand, R. B., & Udayakumar, M. (2014) · Fuel · doi:10.1016/j.fuel.2014.04.034 · Cited by 321
Annamalai, M., Balasubramanian, D., Nanthagopal, K., SivaramaKrishnan, P., Lalvani, J. I. J., Parthasarathy, M., & Annamalai, K. (2016) · Energy Conversion and Management · doi:10.1016/j.enconman.2016.06.062 · Cited by 305
Cited by
Soudagar, M. E. M., Nik-Ghazali, N.-N., Abul Kalam, M., Badruddin, I. A., Banapurmath, N. R., & Akram, N. (2018) · Energy Conversion and Management · doi:10.1016/j.enconman.2018.10.019 · Cited by 528
An updated review on application of nanofluids in heat exchangers for saving energy
Hajatzadeh Pordanjani, A., Aghakhani, S., Afrand, M., Mahmoudi, B., Mahian, O., & Wongwises, S. (2019) · Energy Conversion and Management · doi:10.1016/j.enconman.2019.111886 · Cited by 484
Kılkış, Ş., Krajačić, G., Duić, N., Rosen, M. A., & Al-Nimr, M. A. (2020) · Energy Conversion and Management · doi:10.1016/j.enconman.2020.113410 · Cited by 116
Shekofteh, M., Gundoshmian, T. M., Jahanbakhshi, A., & Heidari-Maleni, A. (2020) · Energy Reports · doi:10.1016/j.egyr.2020.05.025 · Cited by 90
Polat, F. (2022) · Process Safety and Environmental Protection · doi:10.1016/j.psep.2022.03.003 · Cited by 52
Metadata
- Authors
- Chen, A. F., Akmal Adzmi, M., Adam, A., Othman, M. F., Kamaruzzaman, M. K., & Mrwan, A. G.
- Venue
- Energy Conversion and Management
- Publisher
- Elsevier BV
- Published
- 2018-09
- Volume
- 171
- Pages
- 461-477
- ISSN
- 0196-8904 (ISSN-L)
- OpenAlex
- W2807725189
- Cited by
- 262
- References
- 29
- FWCI
- 14.23
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Combustion characteristics, engine performances and emissions of a diesel engine using nanoparticle-diesel fuel blends with aluminium oxide, carbon nanotubes and silicon oxide. https://app.cochat.ai/papers/10.1016/j.enconman.2018.06.004
- The paper
- Chen, A. F., Akmal Adzmi, M., Adam, A., Othman, M. F., Kamaruzzaman, M. K., & Mrwan, A. G. (2018). Combustion characteristics, engine performances and emissions of a diesel engine using nanoparticle-diesel fuel blends with aluminium oxide, carbon nanotubes and silicon oxide. Energy Conversion and Management. https://doi.org/10.1016/j.enconman.2018.06.004
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.