The DOI matches its Crossref record.
Characterization of particulate and gaseous pollutants emitted during operation of a desktop 3D printer
Open accessAbstract
The emission of ultrafine particles (UFP) and gaseous pollutants from 3D printing has been increasingly gaining attention in recent years due to potential health risks. The physical and chemical properties of the emitted particulate matter, however, remain unclear. In this study, we characterized these particles with a focus on their chemical composition and volatility, and measured the gaseous pollutants from desktop 3D printing in a standardized environmental test chamber. Eight types of filaments were tested, including ABS (acrylonitrile butadiene styrene), ASA (acrylonitrile styrene acrylate), HIPS (high impact polystyrene), PETG (polyethylene terephthalate glycol), and PCABS (polycarbonate & ABS). Particle size distribution (PSD), particle number concentration (PNC), particle chemical composition and particle volatility were measured. In addition, volatile and very volatile organic compounds (VOCs and VVOCs) emitted during 3D printing were analyzed. The specific emission rates (SERs) for particles in the size range of 5.6 to 560 nm ranged from 2.0 × 10 9 (GLASS, a PETG-based filament) to 1.7 × 10 11 (ASA) #/min. The particle SERs for ABS were (4.7 ± 1.1) × 10 10 #/min. The SERs for total volatile organic compounds (TVOC) varied from 0.2 μg/min (GLASS) to 40.5 μg/min (ULTRAT, an ABS-based filament). Particles started to evaporate extensively from 150 °C. At 300 °C, only 25% of the particle number remained with the size distribution mode peaked at 11 nm. The particles collected on the quartz filter were mainly composed of semi-volatile organic compounds (SVOCs) associated with the plasticizers, flame-retardants, antioxidants of the thermoplastics, and cyclosiloxanes which may be used as lubricants in the 3D printer.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Colorado, H. A., Velásquez, E. I. G., & Monteiro, S. N. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.04.062 · Cited by 320
Advances in air quality research – current and emerging challenges
Sokhi, R. S., Moussiopoulos, N., Baklanov, A., Bartzis, J., Coll, I., Finardi, S., Friedrich, R., Geels, C., Grönholm, T., Halenka, T., et al. (2022) · Atmospheric Chemistry and Physics · doi:10.5194/acp-22-4615-2022 · Cited by 285
On the environmental impacts of 3D printing technology
Khosravani, M. R., & Reinicke, T. (2020) · Applied Materials Today · doi:10.1016/j.apmt.2020.100689 · Cited by 284
Hayes, A. C., Osio-Norgaard, J., Miller, S., Vance, M. E., & Whiting, G. L. (2021) · ACS ES&T Engineering · doi:10.1021/acsestengg.0c00045 · Cited by 14
Metadata
- Authors
- Gu, J., Wensing, M., Uhde, E., & Salthammer, T.
- Venue
- Environment International
- Publisher
- Elsevier BV
- Published
- 2019-02
- Volume
- 123
- Pages
- 476-485
- ISSN
- 0160-4120 (ISSN-L)
- OpenAlex
- W2906994628
- Cited by
- 158
- References
- 0
- FWCI
- 9.61
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Characterization of particulate and gaseous pollutants emitted during operation of a desktop 3D printer. https://app.cochat.ai/papers/10.1016/j.envint.2018.12.014
- The paper
- Gu, J., Wensing, M., Uhde, E., & Salthammer, T. (2019). Characterization of particulate and gaseous pollutants emitted during operation of a desktop 3D printer. Environment International. https://doi.org/10.1016/j.envint.2018.12.014
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.