The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.
Using triply periodic minimal surfaces (TPMS)-based metal foams structures as skeleton for metal-foam-PCM composites for thermal energy storage and energy management applications
Abstract
Abstract Organic phase change materials (PCMs), such as paraffin wax, have shown great potential for their utilization in latent heat thermal energy storage systems (LHTES). However, due to their low thermal conductivity, they are often hybridized with high thermal conductivity metal foam, resulting in metal foam-PCM composites (MFPCMs) with enhanced heat transfer features. Conventional metal foam is usually idealized using the Kelvin cell. Owing to the recent advances in 3D printing, any complicated topology can however be easily manufactured, which paves a pathway for other complex cell types to be utilized in such energy systems other than Kelvin cell. In this exploratory work, three Triply Periodic Minimal Surfaces (TPMS), i.e., Gyroid, I-graph and wrapped package-graph (IWP), and Primitive cells, are (to the best of the knowledge of the present authors), used for the first time, as skeleton for MFPCMs composites to enhance the effective thermal conductivity of conventional PCMs. Transient numerical simulations were performed to compare the thermal energy storage performance of the used TPMS-based PCM composites with their counterpart based on the conventional Kelvin cell. All structures were tested at the same porosity level and unit cell size of 90% and 7 mm, respectively. Simulations were done under two boundary conditions namely isothermal and isoheat flux conditions. Steady state simulations were also performed to assess the effective thermal conductivity of the used MFPCM composites at temperatures below the melting temperature of used PCM (pure conduction). The obtained results stress that the effective thermal conductivity of MFPCMs strongly depends on the cell type and its unique architecture and not only on the cell porosity where significant increase in the effective thermal conductivity of the MFPCMs composites was achieved when the three TPMS structures are used. Under isothermal condition while considering the Kelvin-based MFPCM as the baseline case, the PCM melting time was reduced by approximately 31% for the Gyroid, 40.3% for the IWP, and 35.3% for the Primitive-based MFPCMs. In isoflux case, the PCM melting time did not show dependence on the type of metal foam structure. However, by considering the temperature homogeneity as a performance indicator (quantified by the maximum and minimum temperature difference in PCM domain), Kelvin-based MFPCM showed the highest value for the difference (least homogenous) whereas, IWP-based MFPCM on average was almost 5 K lesser than the Kelvin-based MFPCM during the entire melting process. Therefore, TPMS structures showed superior performance than the Kelvin cell, let alone than the case of PCM alone, which makes them promising candidates for potential utilization in LHTES applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Tauseef-ur-Rehman, Ali, H. M., Janjua, M. M., Sajjad, U., & Yan, W.-M. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2019.02.001 · Cited by 507
Leong, K. Y., Abdul Rahman, M. R., & Gurunathan, B. A. (2019) · Journal of Energy Storage · doi:10.1016/j.est.2018.11.008 · Cited by 405
Cited by
A review of the state-of-the-art in electronic cooling
Zhang, Z., Wang, X., & Yan, Y. (2021) · e-Prime - Advances in Electrical Engineering, Electronics and Energy · doi:10.1016/j.prime.2021.100009 · Cited by 310
Metadata
- Authors
- Qureshi, Z. A., Al-Omari, S. A. B., Elnajjar, E., Al-Ketan, O., & Al-Rub, R. A.
- Venue
- International Communications in Heat and Mass Transfer
- Publisher
- Elsevier BV
- Published
- 2021-05
- Volume
- 124
- Pages
- 105265
- ISSN
- 0735-1933 (ISSN-L)
- OpenAlex
- W3155266077
- Cited by
- 189
- References
- 2
- FWCI
- 11.72
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Using triply periodic minimal surfaces (TPMS)-based metal foams structures as skeleton for metal-foam-PCM composites for thermal energy storage and energy management applications. https://app.cochat.ai/papers/10.1016/j.icheatmasstransfer.2021.105265
- The paper
- Qureshi, Z. A., Al-Omari, S. A. B., Elnajjar, E., Al-Ketan, O., & Al-Rub, R. A. (2021). Using triply periodic minimal surfaces (TPMS)-based metal foams structures as skeleton for metal-foam-PCM composites for thermal energy storage and energy management applications. International Communications in Heat and Mass Transfer. https://doi.org/10.1016/j.icheatmasstransfer.2021.105265
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.