The DOI matches its Crossref record; 65 of the 65 references it cites were found in a registry or an index; none of the 40 sources its claims cite is checked for support yet.
Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes
Open accessAbstract
A novel reusable, high-compressible cotton regenerated cellulose/chitosan composite aerogel (RC/CSCA) was prepared using N-methylmorpholine-N-oxide (NMMO) as the green cellulose solvent, and glutaraldehyde (GA) as the crosslinking agent. The regenerated cellulose obtained from cotton pulp could chemically crosslink with chitosan and GA, to form a stable 3D porous structure. The GA played an essential role in preventing shrinkage and preserving the deformation recovery ability of RC/CSCA. Due to the ultralow density (13.92 mg/cm3), thermal stability (above 300 °C), and high porosity (97.36 %), the positively charged RC/CSCA can be used as a novel biocomposite adsorbent for effective and selective removal of toxic anionic dyes from wastewater, showing an excellent adsorption capacity, environmental adaptability, and recyclability. The maximal adsorption capacity and removal efficiency of RC/CSCA for methyl orange (MO) was 742.68 mg/g and 95.83 %.
Overview
CoChat Summary
TL;DR
A regenerated cellulose/chitosan composite aerogel (RC/CSCA) crosslinked with glutaraldehyde was prepared using NMMO as a green solvent and showed selective, reusable adsorption of anionic dyes. The optimized RC/CSCA-3 had a maximum Langmuir MO adsorption capacity of 742.68 mg/g and retained 94.57% adsorption after ten cycles.
Key findings
- RC/CSCA-3 (RC:CS = 1:1) removed 95.83% of anionic MO and 90.57% of anionic CR, much more effectively than cationic RhB and MB; in MO/MB mixtures it selectively adsorbed MO and allowed MB to pass.
- The Langmuir maximum MO adsorption capacity at 298 K was 742.68 mg/g (experimental Qmax 730.90 mg/g); adsorption followed monolayer physical/chemical adsorption by kinetics/isotherm fits.
- Adsorption was favored at pH 4, with pHpzc = 6.40; increasing temperature from 25 to 45 °C slightly decreased capacity from 118.07 to 114.71 mg/g, indicating exothermic adsorption. NaCl slightly reduced capacity, while Na2CO3 competed more strongly.
- The aerogel had ultralow density (13.92 mg/cm3), high porosity (97.36%), thermal stability above 300 °C, and water absorption up to 44.91 g/g; GA crosslinking improved mechanical strength, and RC/CSCA-3 retained 94.57% of MO adsorption after ten NaOH/HCl regeneration cycles.
Methods
- RC hydrogel was made by dissolving cotton pulp in NMMO·H2O with ascorbic acid; CS was dissolved in 1 wt% acetic acid; RC suspension (15 mg/mL) was mixed with CS at RC:CS mass ratios 3:1, 3:2, 1:1, and 3:4, crosslinked with glutaraldehyde (3 wt% of chitosan), then freeze-dried. Controls included RCA, CSA, and RC/CSCA-0 without GA.
- Characterization used FE-SEM, FTIR, XRD, TG, XPS, solid-state NMR, compression testing, UV-Vis, pH drift for pHpzc, and ethanol substitution for porosity.
- Batch adsorption used 20 mg aerogel in 50 mL dye solutions (20 mg/L), with pH 3–9, temperatures 25/35/45 °C, and NaCl/Na2CO3 ionic strength tests; kinetics (pseudo-first-order, pseudo-second-order, intraparticle diffusion), isotherms (Langmuir, Freundlich), thermodynamics, and reusability were evaluated. A gravity-driven column (25 mm diameter, 20 cm length, ~0.2 g RC/CSCA) separated MO/MB mixtures.
Limitations
- Stated limitations: Not stated in the paper.
- Evident from the text: adsorption isotherm/kinetic modeling focused on MO, while CR, RhB, and MB were mainly assessed by removal/selectivity comparisons; tests used model dye solutions rather than real wastewater. The continuous-flow separation is described qualitatively (color change and UV-Vis), with no quantitative breakthrough data reported. The text also notes that excessive vertical load destroys the internal orientation structure of RC/CSCA-3.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 2 Not valid · 29 Not checked · 86 Own results and interpretations
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The chemical crosslink of GA with RC and CS via amines or hydroxyl groups enhanced the structural stability of the 3D porous skeleton, refraining from shrinkage and retaining the deformation recovery ability of RC/CSCA.”
§ Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes > Journal Pre-proof
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The GA forms a stronger bond and reinforces the framework of RC/CSCA via the chemical crosslinking of cellulose and chitosan.”
§ Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes > J o u r n a l P r e -p r o o f
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The R 2 of the Langmuir model experimental data is better than that of the Freundlich model at all three temperatures.”
§ Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes > J o u r n a l P r e -p r o o f
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In summary, novel adsorbent RC/CSCA samples were successfully prepared using regenerated cellulose and chitosan as raw materials.”
- Also stated in: § Additional information · plain
“A Novel porous regenerated cellulose/chitosan composite aerogel was prepared.”
§ Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes > 4 CONCLUSIONS
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § Additional information · plain
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The sample with an RC:CS mass ratio of 3:4 exhibits the highest compressive stress, as shown in Fig. 5b.”
§ Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes > J o u r n a l P r e -p r o o f
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
68 more claims
Create a free account to see all 117 claims and every source verdict.
- It may state two separate claims as one. 38
- Probably not a substantial claim. 7
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes > J o u r n a l P r e -p r o o f
“It can be seen that the RC/CSCA sample with a 1:1 mass ratio of RC to CS presents the optimal adsorption rate and capacity.”
§ Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes > Journal Pre-proof
“Compared with composites with ratios 3:1, 3:2, and 1:1, the sample with ratio 3:4 contains more CS, therefore more -NH 3 + groups at the sample surface, resulting in more dye molecules adsorbed and longer adsorption time for reaching the adsorption/desorption equilibrium.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes > J o u r n a l P r e -p r o o f
“Therefore, for pH lower or higher than pH PZC, the surface charge of the sample would be negative or positive, respectively [50].”
§ Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes > J o u r n a l P r e -p r o o f
“In the presence of H + , the amino group of RC/CSCA is protonated to a positive charge, and the sulfonate groups (-SO 3 H) of MO dissociate to form an anion (-SO 3 -).”
Citations
Cites
Adsorption kinetic models: Physical meanings, applications, and solving methods
Wang, J., & Guo, X. (2020) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2020.122156 · Cited by 2,937
On the mechanism of dissolution of cellulose
Lindman, B., Karlström, G., & Stigsson, L. (2010) · Journal of Molecular Liquids · doi:10.1016/j.molliq.2010.04.016 · Cited by 792
Recent Progress in High‐Strength and Robust Regenerated Cellulose Materials
Tu, H., Zhu, M., Duan, B., & Zhang, L. (2021) · Advanced Materials · doi:10.1002/adma.202000682 · Cited by 566
Nanomaterials for removal of toxic elements from water
Lu, F., & Astruc, D. (2018) · Coordination Chemistry Reviews · doi:10.1016/j.ccr.2017.11.003 · Cited by 446
Li, D., Tian, X., Wang, Z., Guan, Z., Li, X., Qiao, H., Ke, H., Luo, L., & Wei, Q. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2019.123127 · Cited by 429
Zhao, X., Wang, X., & Lou, T. (2021) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2020.124054 · Cited by 322
Structure and properties of hydrogels prepared from cellulose in NaOH/urea aqueous solutions
Chang, C., Zhang, L., Zhou, J., Zhang, L., & Kennedy, J. F. (2010) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2010.04.033 · Cited by 295
Flexible electrically conductive biomass-based aerogels for piezoresistive pressure/strain sensors
Huang, J., Li, D., Zhao, M., Ke, H., Mensah, A., Lv, P., Tian, X., & Wei, Q. (2019) · Chemical Engineering Journal · doi:10.1016/j.cej.2019.05.136 · Cited by 261
Acharya, S., Liyanage, S., Parajuli, P., Rumi, S. S., Shamshina, J. L., & Abidi, N. (2021) · Polymers · doi:10.3390/polym13244344 · Cited by 239
Pawar, R. R., Lalhmunsiama, Kim, M., Kim, J.-G., Hong, S.-M., Sawant, S. Y., & Lee, S. M. (2018) · Applied Clay Science · doi:10.1016/j.clay.2018.06.014 · Cited by 238
Cited by
Zhou, Y., Zhang, Y., Nie, Y., Sun, D., Wu, D., Ban, L., Zhang, H., Yang, S., Chen, J., Du, H., et al. (2025) · Progress in Materials Science · doi:10.1016/j.pmatsci.2025.101460 · Cited by 171
Annu, A., Mittal, M., Tripathi, S., & Shin, D. K. (2024) · Polymers · doi:10.3390/polym16020294 · Cited by 128
Serban, G. V., Iancu, V. I., Dinu, C., Tenea, A. G., Vasilache, N., Cristea, I., Niculescu, M., Ionescu, I. A., & Chiriac, F. L. (2023) · Sustainability · doi:10.3390/su151712939 · Cited by 118
Paul, J., Qamar, A., Ahankari, S. S., Thomas, S., & Dufresne, A. (2024) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2024.122198 · Cited by 91
Xiao, W., Sun, R., Hu, S., Meng, C., Xie, B., Yi, M., & Wu, Y. (2023) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2023.126984 · Cited by 70
Metadata
- Authors
- He, S., Li, J., Cao, X., Xie, F., Yang, H., Wang, C., Bittencourt, C., & Li, W.
- Affiliations
- Tianjin University of Technology (CN)
- Zhejiang University (CN)
- University of Mons (BE)
- Corresponding author
- Li, Wenjiang
- Venue
- International Journal of Biological Macromolecules
- Publisher
- Elsevier BV
- Published
- 2023-07
- Volume
- 244
- Pages
- 125067
- ISSN
- 0141-8130 (ISSN-L)
- OpenAlex
- W4378417456
- Semantic Scholar
- c81d7abaaf3127c4ce848482a6ec09433b7d790e
- Cited by
- 93
- References
- 64
- Citations by year
- 2026: 29 · 2025: 25 · 2024: 32 · 2023: 7
- FWCI
- 6.90
- Type
- journal article
- Language
- en
- Open access
- green
- orbi.umons.ac.be
- Licence
- other-oa
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
- www.elsevier.com/legal/tdmrep-license (tdm)
- doi.org/10.15223/policy-017 (stm-asf)
- doi.org/10.15223/policy-037 (stm-asf)
- doi.org/10.15223/policy-012 (stm-asf)
- doi.org/10.15223/policy-029 (stm-asf)
- doi.org/10.15223/policy-004 (stm-asf)
- Locations
- International Journal of Biological Macromolecules (publishedVersion)
- PubMed (publishedVersion)
- ORBi UMONS (submittedVersion, other-oa)
- Funders
- National Natural Science Foundation of China (111 Project, U1764254, 21911530255)
- Fonds De La Recherche Scientifique - FNRS (CDR J001019, J0010-19)
- Higher Education Discipline Innovation Project ((D17003))
- Guangxi Key Research and Development Program (2021AB23009)
- Topics
- Physical Sciences › Environmental Science › Water Science and Technology › Adsorption and biosorption for pollutant removal
- Physical Sciences › Materials Science › Biomaterials › Advanced Cellulose Research Studies
- Physical Sciences › Materials Science › Materials Chemistry › Aerogels and thermal insulation
- Keywords
- regenerated cellulose, chitosan, composite aerogels, anionic dye adsorption, methyl orange, cotton pulp, N-methylmorpholine N-oxide, glutaraldehyde crosslinking, biocomposite adsorbent, wastewater treatment, recyclable adsorbent
- MeSH terms
- Adsorption, Cellulose, Coloring Agents, Water Pollutants, Chemical, Chitosan
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-11-17, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-11-17 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes. https://app.cochat.ai/papers/10.1016/j.ijbiomac.2023.125067
- The paper
- He, S., Li, J., Cao, X., Xie, F., Yang, H., Wang, C., Bittencourt, C., & Li, W. (2023). Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes. International Journal of Biological Macromolecules. https://doi.org/10.1016/j.ijbiomac.2023.125067
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.