The DOI matches its Crossref record; 37 of the 37 references it cites were found in a registry or an index.
High-pressure gaseous hydrogen permeation test method -property of polymeric materials for high-pressure hydrogen devices (1)
Open accessAbstract
Polymeric materials are widely used in hydrogen energy system such as FCEV and hydrogen refueling stations under high-pressure condition. The permeation property (coefficients of permeation, diffusion and solubility) of polymers under high-pressure hydrogen condition should be discussed as parameters to develop those devices. Also the property should be determined to understand influence of the compression by the pressure on polymer materials. A device which can measure gas permeation property of polymer materials accurately in equilibrium state under high-pressure environment is developed, and the reliability of the measurements is ensured. High-pressure hydrogen gas permeability characteristics up to 100 MPa are measured for high-density polyethylene. An advantage of the method is discussed comparing with the non-equilibrium state method, focusing on the hydrostatic pressure effect. Deterioration of hydrogen permeability is observed along with the decrease of diffusion coefficient, which is supposedly affected by hydrostatic compression effect with the increase of environment pressure.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“In addition, because of its high pressure, the permeation of hydrogen gas (permeated hydrogen gas amount) to the vessel wall becomes larger [30] leading to higher risk of accelerated embrittlement.”
From 5917. https://doi.org/10.3390/en14185917. - (2021) · cites this paper as [30]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Prediction of polymer properties
(1993) · Choice Reviews Online · doi:10.5860/choice.31-0937 · Cited by 684
Park, J. Y., & Paul, D. R. (1997) · Journal of Membrane Science · doi:10.1016/s0376-7388(96)00061-0 · Cited by 632
Permeation, diffusion and solution of gases in organic polymers
Barrer, R. M., & Rideal, E. K. (1939) · Transactions of the Faraday Society · doi:10.1039/tf9393500628 · Cited by 584
The Permeability of Different Rubbers to Gases and Its Relation to Diffusivity and Solubility
Van Amerongen, G. J. (1946) · Journal of Applied Physics · doi:10.1063/1.1707667 · Cited by 287
Solubilities of carbon dioxide and nitrogen in polystyrene under high temperature and pressure
Sato, Y., Yurugi, M., Fujiwara, K., Takishima, S., & Masuoka, H. (1996) · Fluid Phase Equilibria · doi:10.1016/s0378-3812(96)03094-4 · Cited by 284
Yamabe, J., & Nishimura, S. (2009) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2008.11.105 · Cited by 224
Self-citationThe Permeability of Different Rubbers to Gases and Its Relation to Diffusivity and Solubility
Amerongen, G. J. V. (1947) · Rubber Chemistry and Technology · doi:10.5254/1.3543282 · Cited by 182
Solubility and Diffusion Coefficient of Carbon Dioxide in Biodegradable Polymers
Satô, Y., Takikawa, T., Sorakubo, A., Takishima, S., Masuoka, H., & Imaizumi, M. (2000) · Industrial & Engineering Chemistry Research · doi:10.1021/ie0001220 · Cited by 145
Prediction of gas barrier properties of high polymers
Salame, M. (1986) · Polymer Engineering and Science · doi:10.1002/pen.760262203 · Cited by 140
Stern, S. A., Mullhaupt, J. T., & Gareis, P. J. (1969) · AIChE Journal · doi:10.1002/aic.690150117 · Cited by 139
Filling procedure for vehicles with compressed hydrogen tanks
Maus, S., Hapke, J., Ranong, C. N., Wüchner, E., Friedlmeier, G., & Wenger, D. (2008) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2008.06.052 · Cited by 134
Failure behavior of rubber O-ring under cyclic exposure to high-pressure hydrogen gas
Yamabe, J., Koga, A., & Nishimura, S. (2013) · Engineering Failure Analysis · doi:10.1016/j.engfailanal.2013.01.034 · Cited by 115
Self-citationEffect of pressure on gas permeability coefficients. A new application of “free volume” theory
Stern, S. A., Fang, S. ‐., & Frisch, H. L. (1972) · Journal of Polymer Science Part A-2 Polymer Physics · doi:10.1002/pol.1972.160100202 · Cited by 93
Koga, A., Uchida, K., Yamabe, J., & Nishimura, S. (2011) · International Journal of Automotive Engineering · doi:10.20485/jsaeijae.2.4_123 · Cited by 76
Self-citationDegradation behavior of acrylonitrile butadiene rubber after cyclic high-pressure hydrogen exposure
Fujiwara, H., Ono, H., & Nishimura, S. (2014) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2014.11.106 · Cited by 75
Self-citationPermeation through plastic films
Li, N. N., & Long, R. B. (1969) · AIChE Journal · doi:10.1002/aic.690150118 · Cited by 73
Naito, Y., Mizoguchi, K., Terada, K., & Kamiya, Y. (1991) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.1991.090290408 · Cited by 66
Flow of Gases through Plastic Membranes
Brubaker, D. W., & Kammermeyer, K. (1953) · Industrial & Engineering Chemistry · doi:10.1021/ie50521a069 · Cited by 58
Satô, Y., Iketani, T., Takishima, S., & Masuoka, H. (2000) · Polymer Engineering and Science · doi:10.1002/pen.11266 · Cited by 57
Permeation of gases at high pressures
Stern, S. A., Fang, S. M., & Jobbins, R. M. (1971) · Journal of Macromolecular Science Part B · doi:10.1080/00222347108212520 · Cited by 54
Stern, S. A., Sampat, S. R., & Kulkarni, S. S. (1986) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.1986.090241001 · Cited by 54
Hiroaki, O. N. O., Fujiwara, H., & Nishimura, S. (2018) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2018.08.031 · Cited by 54
Self-citationStern, S. A., Kulkarni, S. S., & Frisch, H. L. (1983) · Journal of Polymer Science Polymer Physics Edition · doi:10.1002/pol.1983.180210311 · Cited by 53
Hiroaki, O. N. O., Fujiwara, H., Onoue, K., & Nishimura, S. (2019) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2019.07.035 · Cited by 47
Self-citationAllowable hydrogen permeation rate from road vehicles
Adams, P. G., Bengaouer, A., Cariteau, B., Molkov, V., & Venetsanos, A. G. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.04.161 · Cited by 42
Hydrogen influence on the tensile properties of mono and multi-layer polymers for gas distribution
Castagnet, S., Grandidier, J.-C., Comyn, M., & Benoît, G. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.04.155 · Cited by 41
Bonner, D. C., & Cheng, Y. (1975) · Journal of Polymer Science Polymer Letters Edition · doi:10.1002/pol.1975.130130502 · Cited by 41
Pressure–Strain and Pressure–Volume Relationships in the Crystal Lattice of Polyethylene at 293°K
Ito, T., & Marui, H. (1971) · Polymer Journal · doi:10.1295/polymj.2.768 · Cited by 40
A Visualizing Study of Blister Initiation Behavior by Gas Decompression
Koga, A., Yamabe, T., Satō, H., Uchida, K., Nakayama, J., Yamabe, J., & Nishimura, S. (2013) · Tribology online · doi:10.2474/trol.8.68 · Cited by 31
Self-citationPrewitz, M., Gaber, M., Müller, R., Marotztke, C., & Holtappels, K. (2018) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2017.12.092 · Cited by 30
Onoue, K., Murakami, Y., & Sofronis, P. (2012) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2012.02.096 · Cited by 27
Self-citationPermeation of gases through polyethylene films at elevated pressures
Li, N. N., & Henley, E. J. (1964) · AIChE Journal · doi:10.1002/aic.690100518 · Cited by 27
Yamabe, J., NAKAO, M., Fujiwara, H., & Nishimura, S. (2008) · TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A · doi:10.1299/kikaia.74.971 · Cited by 23
Self-citationSorption and partial molar volumes of gases in poly(ethylene‐co‐vinyl acetate)
Kamiya, Y., Naito, Y., & Bourbon, D. (1994) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.1994.090320209 · Cited by 22
Permeation of high‐pressure gases in poly(ethylene‐co‐vinyl acetate)
Naito, Y., Bourbon, D., Terada, K., & Kamiya, Y. (1993) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.1993.090310609 · Cited by 19
Fujiwara, H. (2017) · International Polymer Science and Technology · doi:10.1177/0307174x1704400308 · Cited by 19
Self-citationSeparation of gaseous mixtures by permeation through polyethylene film
Reilly, J. W., Henley, E. J., & Staffin, H. K. (1970) · AIChE Journal · doi:10.1002/aic.690160307 · Cited by 8
Research works printed but not linked: 1
- Matsuzaki, 1987, Effect of surface roughness on compressive stress of static seales nippon kikai gakkai ronbunshu, Chimia, 53, 1091
Cited by
(2021) · doi:10.3390/en14185917 · Cited by 708
Metadata
- Authors
- Fujiwara, H., Ono, H., Onoue, K., & Nishimura, S.
- Affiliations
- Research Center for Hydrogen Industrial Use and Storage, Kyushu University (JP)
- Kyushu University (JP)
- Corresponding author
- Fujiwara, Hirotada
- Venue
- International Journal of Hydrogen Energy
- Publisher
- Elsevier BV
- Published
- 2020-10
- Volume
- 45
- Issue
- 53
- Pages
- 29082-29094
- ISSN
- 0360-3199 (ISSN-L)
- OpenAlex
- W3081418981
- Cited by
- 150
- References
- 37
- Citations by year
- 2026: 30 · 2025: 58 · 2024: 22 · 2023: 21 · 2022: 9 · 2021: 8 · 2020: 2
- FWCI
- 4.92
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by-nc-nd
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
- www.elsevier.com/legal/tdmrep-license (tdm)
- creativecommons.org/licenses/by-nc-nd/4.0/ (vor)
- Locations
- International Journal of Hydrogen Energy (publishedVersion, cc-by-nc-nd)
- Funders
- New Energy and Industrial Technology Development Organization
- Topics
- Physical Sciences › Chemical Engineering › Filtration and Separation › Membrane Separation and Gas Transport
- Physical Sciences › Materials Science › Materials Chemistry › Hydrogen Storage and Materials
- Physical Sciences › Materials Science › Metals and Alloys › Hydrogen embrittlement and corrosion behaviors in metals
- Keywords
- hydrogen permeation, high-pressure hydrogen, high-density polyethylene, hydrogen diffusion coefficient, hydrogen solubility, hydrostatic compression, equilibrium measurements, fuel cell vehicles, hydrogen refueling stations
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
