The DOI matches its Crossref record; 9 of the 9 references it cites were found in a registry or an index.
Effects of high speed in the drilling of glass fibre reinforced plastic: Evaluation of the delamination factor
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Materials science and engineering: An introduction
Clayton, C. R. (1987) · Materials Science and Engineering · doi:10.1016/0025-5416(87)90343-0 · Cited by 5,925
Materials Science and Engineering: An Introduction
Callister, W. D. (1985) · Cited by 5,351
DAVIM, J., RUBIO, J., & ABRAO, A. (2007) · Composites Science and Technology · doi:10.1016/j.compscitech.2006.10.009 · Cited by 551
Self-citationEffects of special drill bits on drilling-induced delamination of composite materials
Hocheng, H., & Tsao, C. C. (2006) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2005.10.004 · Cited by 423
Experimental study of drilling glass fiber reinforced plastics (GFRP) manufactured by hand lay-up
Davim, J. P., Reis, P., & António, C. C. (2004) · Composites Science and Technology · doi:10.1016/s0266-3538(03)00253-7 · Cited by 388
Self-citationFactors affecting the machinability of GFR/epoxy composites
El-Sonbaty, I., Khashaba, U. A., & Machaly, T. (2004) · Composite Structures · doi:10.1016/s0263-8223(03)00181-8 · Cited by 316
The effect of vibratory drilling on hole quality in polymeric composites
Arul, S., Vijayaraghavan, L., Malhotra, S. K., & Krishnamurthy, R. (2005) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2005.05.023 · Cited by 227
Quiza, R., Reis, P., & Davim, J. P. (2006) · Composites Science and Technology · doi:10.1016/j.compscitech.2006.05.003 · Cited by 152
Self-citationDavim, J. P., Reis, P., & António, C. A. C. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2004.04.173 · Cited by 104
Self-citation
Cited by
A review of mechanical drilling for composite laminates
Liu, D., Tang, Y., & Cong, W. L. (2012) · Composite Structures · doi:10.1016/j.compstruct.2011.11.024 · Cited by 781
Natural fiber–reinforced composites: A review on material, manufacturing, and machinability
Lotfi, A., Li, H., Dao, D. V., & Prusty, G. (2021) · Journal of Thermoplastic Composite Materials · doi:10.1177/0892705719844546 · Cited by 499
Delamination formation, evaluation and suppression during drilling of composite laminates: A review
Geng, D., Liu, Y., Shao, Z., Lu, Z., Cai, J., Li, X., Jiang, X., & Zhang, D. (2019) · Composite Structures · doi:10.1016/j.compstruct.2019.02.099 · Cited by 465
Krishnaraj, V., Prabukarthi, A., Ramanathan, A., Elanghovan, N., Senthil Kumar, M., Zitoune, R., & Davim, J. P. (2012) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2012.01.007 · Cited by 400
Self-citationRecent advances in drilling of carbon fiber–reinforced polymers for aerospace applications: a review
Aamir, M., Tolouei-Rad, M., Giasin, K., & Nosrati, A. (2019) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-019-04348-z · Cited by 329
Metadata
- Authors
- Campos Rubio, J., Abrao, A. M., Faria, P. E., Correia, A. E., & Davim, J. P.
- Venue
- International Journal of Machine Tools and Manufacture
- Publisher
- Elsevier BV
- Published
- 2008-05
- Volume
- 48
- Issue
- 6
- Pages
- 715-720
- ISSN
- 0890-6955 (ISSN-L)
- OpenAlex
- W2080709749
- Cited by
- 297
- References
- 9
- FWCI
- 6.14
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effects of high speed in the drilling of glass fibre reinforced plastic: Evaluation of the delamination factor. https://app.cochat.ai/papers/10.1016/j.ijmachtools.2007.10.015
- The paper
- Campos Rubio, J., Abrao, A. M., Faria, P. E., Correia, A. E., & Davim, J. P. (2008). Effects of high speed in the drilling of glass fibre reinforced plastic: Evaluation of the delamination factor. International Journal of Machine Tools and Manufacture. https://doi.org/10.1016/j.ijmachtools.2007.10.015
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.