The DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index.
Sheet and network based functionally graded lattice structures manufactured by selective laser melting: Design, mechanical properties, and simulation
Abstract
Abstract The triply periodic minimal surfaces (TPMS) have caught a lot of attention to many applications recently such as biomaterials, lightweight components with high strength and functionally graded material (FGM). In this study, the designing methods of the network based functionally graded Gyroid (N-FGG) and sheet based functionally graded Gyroid (S-FGG) structures were presented. The specimens of N-FGG and S-FGG based structures were fabricated by selective laser melting (SLM) with Ti-6Al-4V powder, then followed by quasi-static compression tests to measure the mechanical properties. The S-FGG based structure showed higher elastic modulus, yield strength and more stable stress fluctuation than N-FGG based structure with the same range of volume fraction gradient. The dominated deformation behaviors of both graded lattice structures were layer-by-layer. However, the S-FGG based structure showed more of buckling failure while the N-FGG based structure exhibited more of brittle fracture. Furthermore, the finite element analysis (FEA) with the Johnson-Cook plastic and damage models was implemented to simulate the plastic deformation and the failure behavior of the lattice materials at the post-yield stages. The simulated results illustrated that the compressive stress concentrated in the middle area of struts which connected the two adjacent layers of N-FGG based structures, while the stress in S-FGG based structures was distributed much uniformly in the middle connection region. S-FGG based structure also showed higher ultimate stress with the increase of compressive strain. Finally, the energy absorption capability of lattice structures was investigated, and the results indicated that the S-FGG based structure showed more total energy absorption per unit volume and higher energy efficiency, which means good prospects especially in the applications of relatively high allowable stress.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing: technology, applications and research needs
Guo, N., & Leu, M. C. (2013) · Frontiers of Mechanical Engineering · doi:10.1007/s11465-013-0248-8 · Cited by 2,073
Thermophysical properties of high porosity metal foams
Bhattacharya, A., Calmidi, V. V., & Mahajan, R. L. (2002) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(01)00220-4 · Cited by 1,233
Al-Ketan, O., Rowshan, R., & Abu Al-Rub, R. K. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2017.12.006 · Cited by 941
Defect formation mechanisms in selective laser melting: a review
Zhang, B., Li, Y., & Bai, Q. (2017) · Chinese Journal of Mechanical Engineering · doi:10.1007/s10033-017-0121-5 · Cited by 924
Zhang, L., Feih, S., Daynes, S., Chang, S., Wang, M. Y., Wei, J., & Lu, W. F. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.08.007 · Cited by 780
Evaluations of cellular lattice structures manufactured using selective laser melting
Yan, C., Hao, L., Hussein, A., & Raymont, D. (2012) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2012.06.002 · Cited by 730
Maskery, I., Sturm, L., Aremu, A. O., Panesar, A., Williams, C. B., Tuck, C. J., Wildman, R. D., Ashcroft, I. A., & Hague, R. J. M. (2018) · Polymer · doi:10.1016/j.polymer.2017.11.049 · Cited by 728
Maskery, I., Aboulkhair, N. T., Aremu, A. O., Tuck, C. J., Ashcroft, I. A., Wildman, R. D., & Hague, R. J. M. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2016.06.013 · Cited by 706
Yan, C., Hao, L., Hussein, A., Young, P., & Raymont, D. (2014) · Materials & Design · doi:10.1016/j.matdes.2013.10.027 · Cited by 622
Minimal surface scaffold designs for tissue engineering
Kapfer, S. C., Hyde, S. T., Mecke, K., Arns, C. H., & Schröder-Turk, G. E. (2011) · Biomaterials · doi:10.1016/j.biomaterials.2011.06.012 · Cited by 579
Cited by
Feng, J., Fu, J., Yao, X., & He, Y. (2022) · International Journal of Extreme Manufacturing · doi:10.1088/2631-7990/ac5be6 · Cited by 813
Wu, Y., Fang, J., Wu, C., Li, C., Sun, G., & Li, Q. (2023) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2023.108102 · Cited by 440
Metadata
- Authors
- Zhou, H., Zhao, M., Ma, Z., Zhang, D. Z., & Fu, G.
- Venue
- International Journal of Mechanical Sciences
- Publisher
- Elsevier BV
- Published
- 2020-06
- Volume
- 175
- Pages
- 105480
- ISSN
- 0020-7403 (ISSN-L)
- OpenAlex
- W3002730896
- Cited by
- 265
- References
- 35
- FWCI
- 15.43
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Sheet and network based functionally graded lattice structures manufactured by selective laser melting: Design, mechanical properties, and simulation. https://app.cochat.ai/papers/10.1016/j.ijmecsci.2020.105480
- The paper
- Zhou, H., Zhao, M., Ma, Z., Zhang, D. Z., & Fu, G. (2020). Sheet and network based functionally graded lattice structures manufactured by selective laser melting: Design, mechanical properties, and simulation. International Journal of Mechanical Sciences. https://doi.org/10.1016/j.ijmecsci.2020.105480
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.