The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Strength and ductility of CrFeCoNiMo alloy with hierarchical microstructures
Open accessAbstract
Abstract Single-phase multi-principal-element alloys (MPEAs) with face-centered cubic (FCC) structure generally exhibit low yield strength but superb ductility and strain hardening capability. In this work, we demonstrate that enhancing yield strength while retaining good ductility of single phase FCC MPEAs can be achieved by developing hierarchical microstructures. A non-equiatomic Cr20Fe6Co34Ni34Mo6 alloy with single-phase FCC structure was fabricated and immediately cold-rolled with ∼70% thickness reduction after a liquid nitrogen bath. The cold-rolled sample was then annealed at various temperatures in a range of 675–1150 °C for various periods. As annealing temperature exceeds 800 °C, annealed samples exhibit coarse-grained microstructure and low yield strength, while high strain hardening rate and good ductility. As annealing temperature is lower than 800 °C, annealed samples develop hierarchical microstructures that comprise high density of annealing nano-twins in recrystallized fine grains (grain size ∼ 1 μm) and stable dislocation walls in non-fully recrystallized fine grains. The addition of Mo in the system is found to be very effective in retarding the recrystallization and grain growth, promoting formation of recrystallized fine grains. Mechanical tensile testing reveals that such kind of hierarchical microstructure enhances yield strength of single phase FCC MPEAs (1.1 GPa) while retains good ductility (uniform elongation of ∼29%) and high ultimate tensile strength (1.3 GPa). Grain boundaries, twin boundaries and dislocation walls act as strong barriers for dislocation motion, enhancing yield strength and strain hardening capacity. Dislocation walls also act as sources for dislocations and deformation twins at large deformation stages, retaining a good ductility. Engineering such hierarchical microstructures should thus be an efficient strategy in enhancing mechanical properties of FCC MPEAs with low or medium stacking fault energies.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
The conflicts between strength and toughness
Ritchie, R. O. (2011) · Nature Materials · doi:10.1038/nmat3115 · Cited by 3,989
Cited by
High-entropy alloys with heterogeneous microstructure: Processing and mechanical properties
Sathiyamoorthi, P., & Kim, H. S. (2022) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100709 · Cited by 766
Tailoring heterogeneities in high-entropy alloys to promote strength–ductility synergy
Ma, E., & Wu, X. (2019) · Nature Communications · doi:10.1038/s41467-019-13311-1 · Cited by 621
Nanoprecipitate‐Strengthened High‐Entropy Alloys
Liu, L., Zhang, Y., Han, J., Wang, X., Jiang, W., Liu, C., Zhang, Z., & Liaw, P. K. (2021) · Advanced Science · doi:10.1002/advs.202100870 · Cited by 393
A review on the dynamic-mechanical behaviors of high-entropy alloys
Tang, Y., Wang, R., Xiao, B., Zhang, Z., Li, S., Qiao, J., Bai, S., Zhang, Y., & Liaw, P. K. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101090 · Cited by 314
Zhang, T. W., Ma, S. G., Zhao, D., Wu, Y. C., Zhang, Y., Wang, Z. H., & Qiao, J. W. (2020) · International Journal of Plasticity · doi:10.1016/j.ijplas.2019.08.013 · Cited by 293
Metadata
- Authors
- Ming, K., Bi, X., & Wang, J.
- Venue
- International Journal of Plasticity
- Publisher
- Elsevier BV
- Published
- 2019-02
- Volume
- 113
- Pages
- 255-268
- ISSN
- 0749-6419 (ISSN-L)
- OpenAlex
- W2896724308
- Cited by
- 200
- References
- 1
- FWCI
- 10.39
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Strength and ductility of CrFeCoNiMo alloy with hierarchical microstructures. https://app.cochat.ai/papers/10.1016/j.ijplas.2018.10.005
- The paper
- Ming, K., Bi, X., & Wang, J. (2019). Strength and ductility of CrFeCoNiMo alloy with hierarchical microstructures. International Journal of Plasticity. https://doi.org/10.1016/j.ijplas.2018.10.005
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.