The DOI matches its Crossref record.
Microstructures and properties of an equimolar AlCoCrFeNi high entropy alloy printed by selective laser melting
Abstract
Abstract The equimolar AlCoCrFeNi high entropy alloy (HEA) was printed by selective laser melting (SLM), with emphasis on its densification, phase identification, non-equilibrium microstructure and properties. The density of SLM samples increase gradually with the increase of volumetric energy density (VED) with the maximal relative density 98.4%. SLM samples are consisted of disordered body-center cubic phases (A2) and ordered body-center cubic phases (B2) which are different from the conventional cast or deformation with A2 and fcc phase; the content of B2 phase increases with the VED. Interestingly, the Fe-Cr precipitate, which has never been found in the cast one, is observed in the SLM one without heat treatment. The microstructure of SLM samples shows epitaxial growth of columnar A2 grain bundles perpendicular to the melt pool boundary with an average grain size of about 1.5 μm; the B2 phase is between the columnar A2 grains. At low VED, the SLM sample shows preferred orientation, and is gradually transformed to the crystallographic direction families at a higher VED. Besides, there exists the {100}A2∥{100}B2 orientation relationship in A2 and B2 phase. The maximal micro-hardness of 632.8Hv of SLM sample is higher than the cast one and the electron beam melting printed one.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
Recent Advances on High‐Entropy Alloys for 3D Printing
Han, C., Fang, Q., Shi, Y., Tor, S. B., Chua, C. K., & Zhou, K. (2020) · Advanced Materials · doi:10.1002/adma.201903855 · Cited by 486
Additive manufacturing of high entropy alloys: A practical review
Ostovari Moghaddam, A., Shaburova, N. A., Samodurova, M. N., Abdollahzadeh, A., & Trofimov, E. A. (2021) · Journal of Materials Science & Technology · doi:10.1016/j.jmst.2020.11.029 · Cited by 474
Laser powder bed fusion for metal additive manufacturing: perspectives on recent developments
Sing, S. L., & Yeong, W. Y. (2020) · Virtual and Physical Prototyping · doi:10.1080/17452759.2020.1779999 · Cited by 379
Sing, S. L., Huang, S., Goh, G. D., Goh, G. L., Tey, C. F., Tan, J. H. K., & Yeong, W. Y. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2021.100795 · Cited by 328
Metadata
- Authors
- Niu, P. D., Li, R. D., Yuan, T. C., Zhu, S. Y., Chen, C., Wang, M. B., & Huang, L.
- Venue
- Intermetallics
- Publisher
- Elsevier BV
- Published
- 2019-01
- Volume
- 104
- Pages
- 24-32
- ISSN
- 0966-9795 (ISSN-L)
- OpenAlex
- W2899139153
- Cited by
- 247
- References
- 0
- FWCI
- 12.79
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Microstructures and properties of an equimolar AlCoCrFeNi high entropy alloy printed by selective laser melting. https://app.cochat.ai/papers/10.1016/j.intermet.2018.10.018
- The paper
- Niu, P. D., Li, R. D., Yuan, T. C., Zhu, S. Y., Chen, C., Wang, M. B., & Huang, L. (2019). Microstructures and properties of an equimolar AlCoCrFeNi high entropy alloy printed by selective laser melting. Intermetallics. https://doi.org/10.1016/j.intermet.2018.10.018
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.