Student or educator? Sign up with your school email and get 6 months of Pro free.
Cited by 110

The DOI matches its Crossref record; the references it cites are not checked yet.

Optimization of the balance between high strength and high electrical conductivity in CuCrZr alloys through two-step cryorolling and aging

Li, Rengeng, Guo, Enyu, Chen, Zongning, Kang, Huijun, Wang, Wei, Zou, Cunlei, Li, Tingju, Wang, Tongmin·2019·Journal of Alloys and Compounds

Abstract

Abstract A two-step cryorolling and aging process was developed to fabricate high strength and high electrical conductivity CuCrZr alloys. The microstructural evolution, mechanical and electrical properties of Cu-1Cr-0.1Zr (wt.%) alloys subjected to the two-step cryorolling and aging process were investigated. The results showed that this two-step process reduced the width of the deformation bands from 113 nm to 80 nm. The introduction of precipitates in the matrix during intermediate aging was responsible for the narrowing of the deformation bands. Even though the cryorolled sample underwent detwinning, its ultimate tensile strength improved by ∼35 MPa. Ordered face-centered cubic (fcc) Cr precipitates ∼5 nm in size were observed in the Cu matrix, and these precipitates had a pinning effect on the motion of boundaries. A desired balance between the ultimate tensile strength (648 MPa) and electrical conductivity (79.80% IACS) was achieved by the coexistence of refined deformation bands, nanoscale deformation twins and nanoprecipitates.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1016/j.jallcom.2018.09.040

Cites

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

The citation lists haven’t been fetched yet

Cited by 110

Research works printed but not linked: 34

  1. Kulczyk, 2018, Improved compromise between the electrical conductivity and hardness of the thermo-mechanically treated CuCrZr alloy, Mater. Sci. Eng. A, 724, 45, 10.1016/j.msea.2018.03.004 · doi:10.1016/j.msea.2018.03.004
  2. Zhai, 2012, A DSC analysis of thermodynamic properties and solidification characteristics for binary Cu-Sn alloys, Acta Mater., 60, 6518, 10.1016/j.actamat.2012.08.013 · doi:10.1016/j.actamat.2012.08.013
  3. Li, 2017, Microstructure and properties of a novel Cu-Mg-Ca alloy with high strength and high electrical conductivity, J. Alloys Compd., 723, 1162, 10.1016/j.jallcom.2017.06.155 · doi:10.1016/j.jallcom.2017.06.155
  4. Liang, 2018, A multiscale architectured CuCrZr alloy with high strength, electrical conductivity and thermal stability, J. Alloys Compd., 735, 1389, 10.1016/j.jallcom.2017.11.309 · DOI
  5. Pang, 2014, Effects of Zr and (Ni, Si) additions on properties and microstructure of Cu–Cr alloy, J. Alloys Compd., 582, 786, 10.1016/j.jallcom.2013.08.146 · doi:10.1016/j.jallcom.2013.08.146
  6. Chenna Krishna, 2017, High strength, utilizable ductility and electrical conductivity in cold rolled sheets of Cu-Cr-Zr-Ti alloy, J. Mater. Eng. Perform., 27, 787, 10.1007/s11665-017-3111-y · doi:10.1007/s11665-017-3111-y
  7. Vinogradov, 2002, Structure and properties of ultra-fine grain Cu–Cr–Zr alloy produced by equal-channel angular pressing, Acta Mater., 50, 1639, 10.1016/S1359-6454(01)00437-2 · DOI
  8. Sun, 2015, A high strength and high electrical conductivity bulk CuCrZr alloy with nanotwins, Scripta Mater., 99, 73, 10.1016/j.scriptamat.2014.11.032 · DOI
  9. Li, 2016, A promising structure for fabricating high strength and high electrical conductivity copper alloys, Sci. Rep., 6, 20799, 10.1038/srep20799 · DOI
  10. Song, 2017, Microstructural evolution and service performance of cold-drawn pure aluminum conductor wires, J. Mater. Sci. Technol., 33, 1039, 10.1016/j.jmst.2016.11.018 · doi:10.1016/j.jmst.2016.11.018
  11. Zhao, 2006, Simultaneously increasing the ductility and strength of nanostructured alloys, Adv. Mater., 18, 2280, 10.1002/adma.200600310 · doi:10.1002/adma.200600310
  12. Chen, 2016, The effect of initial aging treatment on the microstructure and mechanical properties of cryorolled 6016 Al alloy, Mater. Sci. Eng. A, 667, 311, 10.1016/j.msea.2016.04.099 · doi:10.1016/j.msea.2016.04.099
  13. Ye, 2014, Enhanced strength and electrical conductivity of Cu–Zr–B alloy by double deformation–aging process, J. Alloys Compd., 615, 249, 10.1016/j.jallcom.2014.07.010 · doi:10.1016/j.jallcom.2014.07.010
  14. Zhang, 2017, A high strength and high electrical conductivity Cu-Cr-Zr alloy fabricated by cryorolling and intermediate aging treatment, Mater. Sci. Eng. A, 680, 108, 10.1016/j.msea.2016.10.087 · DOI · Paper page
  15. Cheng, 2013, Precipitation in a Cu–Cr–Zr–Mg alloy during aging, Mater. Char., 81, 68, 10.1016/j.matchar.2013.04.008 · doi:10.1016/j.matchar.2013.04.008
  16. Zhou, 2008, Microstructure and properties of Cu–1.0Cr–0.2Zr–0.03Fe alloy, Mater. Sci. Eng. A, 498, 225, 10.1016/j.msea.2008.07.061 · doi:10.1016/j.msea.2008.07.061
  17. Bay, 1992, Overview no. 96 evolution of f.c.c. deformation structures in polyslip, Acta Metall. Mater., 40, 205, 10.1016/0956-7151(92)90296-Q · doi:10.1016/0956-7151(92)90296-q
  18. Hansen, 2001, Microstructural evolution and hardening parameters, Mater. Sci. Eng. A, 317, 3, 10.1016/S0921-5093(01)01191-1 · doi:10.1016/s0921-5093(01)01191-1
  19. Xia, 2012, Study of deformation and aging behaviors of a hot rolled–quenched Cu–Cr–Zr–Mg–Si alloy during thermomechanical treatments, Mater. Des., 39, 404, 10.1016/j.matdes.2012.03.003 · doi:10.1016/j.matdes.2012.03.003
  20. Hughes, 2000, Microstructure and strength of nickel at large strains, Acta Mater., 48, 2985, 10.1016/S1359-6454(00)00082-3 · doi:10.1016/s1359-6454(00)00082-3
  21. Zhang, 2012, Superior thermal stability of coherent twin boundaries in nanotwinned metals, Scripta Mater., 66, 860, 10.1016/j.scriptamat.2012.01.026 · doi:10.1016/j.scriptamat.2012.01.026
  22. Szczerba, 2016, Experimental studies on detwinning of face-centered cubic deformation twins, Acta Mater., 104, 52, 10.1016/j.actamat.2015.11.025 · doi:10.1016/j.actamat.2015.11.025
  23. Chen, 2017, Radiation induced detwinning in nanotwinned Cu, Scripta Mater., 130, 37, 10.1016/j.scriptamat.2016.10.033 · doi:10.1016/j.scriptamat.2016.10.033
  24. Zhang, 2015, Dislocation-twin boundary interactions induced nanocrystalline via SPD processing in bulk metals, Sci. Rep., 5, 8981, 10.1038/srep08981 · doi:10.1038/srep08981
  25. Wang, 2010, Detwinning mechanisms for growth twins in face-centered cubic metals, Acta Mater., 58, 2262, 10.1016/j.actamat.2009.12.013 · doi:10.1016/j.actamat.2009.12.013
  26. Wen, 2013, Strengthening mechanisms in a high-strength bulk nanostructured Cu–Zn–Al alloy processed via cryomilling and spark plasma sintering, Acta Mater., 61, 2769, 10.1016/j.actamat.2012.09.036 · doi:10.1016/j.actamat.2012.09.036
  27. Fujii, 2000, Crystallography and morphology of nanosized Cr particles in a Cu-0.2% Cr alloy, Acta Mater., 48, 1033, 10.1016/S1359-6454(99)00411-5 · doi:10.1016/s1359-6454(99)00411-5
  28. Chen, 2017, Structure and orientation relationship of new precipitates in a Cu–Cr–Zr alloy, Mater. Sci. Technol., 34, 282, 10.1080/02670836.2017.1376428 · doi:10.1080/02670836.2017.1376428
  29. Lu, 2004, Ultrahigh strength and high electrical conductivity in copper, Science, 304, 422, 10.1126/science.1092905 · DOI · Paper page
  30. Guan, 2017, A high-strength, ductile Al-0.35Sc-0.2Zr alloy with good electrical conductivity strengthened by coherent nanosized-precipitates, J. Mater. Sci. Technol., 33, 215, 10.1016/j.jmst.2017.01.017 · doi:10.1016/j.jmst.2017.01.017
  31. Hutchinson, 2008, The comparative effectiveness of Nb solute and NbC precipitates at impeding grain-boundary motion in Nb steels, Scripta Mater., 59, 635, 10.1016/j.scriptamat.2008.05.036 · DOI
  32. Liu, 1999, Aging precipitation and recrystallization of rapidly solidified Cu-Cr-Zr-Mg alloy, Mater. Sci. Eng. A, 265, 262, 10.1016/S0921-5093(98)01149-6 · doi:10.1016/s0921-5093(98)01149-6
  33. Su, 2007, Recrystallization and precipitation behavior of Cu-Cr-Zr alloy, J. Mater. Eng. Perform., 16, 490, 10.1007/s11665-007-9071-x · doi:10.1007/s11665-007-9071-x
  34. Han, 2009, The effects of grain boundary precipitates on cryogenic properties of aged 316-type stainless steels, Mater. Sci. Eng. A, 516, 169, 10.1016/j.msea.2009.03.009 · doi:10.1016/j.msea.2009.03.009

Metadata

Authors
Li, R., Guo, E., Chen, Z., Kang, H., Wang, W., Zou, C., Li, T., & Wang, T.
Venue
Journal of Alloys and Compounds
Publisher
Elsevier BV
Published
2019-01
Volume
771
Pages
1044-1051
ISSN
0925-8388
Cited by
110
Language
en
Funders
  • National Natural Science Foundation of China (51525401, 51601028, 51774065)
  • National Basic Research Program of China (2017YFA0403803)

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Optimization of the balance between high strength and high electrical conductivity in CuCrZr alloys through two-step cryorolling and aging. https://app.cochat.ai/papers/10.1016/j.jallcom.2018.09.040
The paper
Li, R., Guo, E., Chen, Z., Kang, H., Wang, W., Zou, C., Li, T., & Wang, T. (2019). Optimization of the balance between high strength and high electrical conductivity in CuCrZr alloys through two-step cryorolling and aging. Journal of Alloys and Compounds. https://doi.org/10.1016/j.jallcom.2018.09.040

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.