The DOI matches its Crossref record; 42 of the 42 references it cites were found in a registry or an index.
Potentials and strategies of solid-state additive friction-stir manufacturing technology: A critical review
Abstract
In this assessment, novel applications of solid-state technology based on friction-stir processing (FSP) principles are appraised for use in additive manufacturing (AM) of metals/alloys and metal matrix composites, as variations of so-called additive friction-stir manufacturing (AFSM). Multiple variants of this technique involve layer-by-layer deposition of materials by thermo-mechanical stirring of a rotating tool to induce high temperature via severe plastic deformation (SPD) and may involve: (i) feeding of new material from powder/wire, (ii) surface cladding, (iii) functionally graded modification of composition, (iv) friction-surfacing, and (v) FSP as modification to the other techniques. This emerging material synthesis technique incorporates high strain rates (1 to 1000 s−1) and high temperature (∼0.8 Tm) through intense plastic deformation while imposing equivalent plastic strains of up to ∼40, leading to rapid thermal cycles. Materials mixing during deposition of each layer forms fully dense and homogenous structures with significant microstructural refinement which is free of any melting and re-solidification defects such as shrinkage micro-voids, porosities, and cracks. The manufactured components by this solid-state technology may enable lower levels of residual stress and distortion as compared to the fusion-based additive processes, and the potential to achieve superior and isotropic strength and ductility, while drastically increasing material production rates. These features are reviewed here while also providing an outlook on future areas and ongoing challenges for this emerging technology.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Friction stir welding and processing
Mishra, R. S., & Ma, Z. Y. (2005) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2005.07.001 · Cited by 6,753
Friction stir welding and processing
(2008) · Choice Reviews Online · doi:10.5860/choice.46-0901 · Cited by 3,862
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
Additive manufacturing and its societal impact: a literature review
Huang, S. H., Liu, P., Mokasdar, A., & Hou, L. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-012-4558-5 · Cited by 1,862
Carroll, B. E., Palmer, T. A., & Beese, A. M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.12.054 · Cited by 1,507
Kok, Y., Tan, X. P., Wang, P., Nai, M. L. S., Loh, N. H., Liu, E., & Tor, S. B. (2018) · Materials & Design · doi:10.1016/j.matdes.2017.11.021 · Cited by 1,447
A review on 3D micro-additive manufacturing technologies
Vaezi, M., Seitz, H., & Yang, S. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-012-4605-2 · Cited by 1,293
Friction Stir Processing Technology: A Review
Ma, Z. Y. (2008) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-007-9459-0 · Cited by 1,206
Cited by
Heidarzadeh, A., Mironov, S., Kaibyshev, R., Çam, G., Simar, A., Gerlich, A., Khodabakhshi, F., Mostafaei, A., Field, D. P., Robson, J. D., et al. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100752 · Cited by 1,048
Self-citationGriffiths, R. J., Garcia, D., Song, J., Vasudevan, V. K., Steiner, M. A., Cai, W., & Yu, H. Z. (2021) · Materialia · doi:10.1016/j.mtla.2020.100967 · Cited by 236
Metadata
- Authors
- Khodabakhshi, F., & Gerlich, A. P.
- Venue
- Journal of Manufacturing Processes
- Publisher
- Elsevier BV
- Published
- 2018-12
- Volume
- 36
- Pages
- 77-92
- ISSN
- 1526-6125 (ISSN-L)
- OpenAlex
- W2894690490
- Cited by
- 268
- References
- 42
- FWCI
- 10.55
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.