The DOI matches its Crossref record; 12 of the 12 references it cites were found in a registry or an index.
Dry machining of Inconel 718, workpiece surface integrity
Open accessAbstract
In the machining of Inconel 718, nickel based heat resistant superalloy and classified difficult-to-cut material, the consumption of cooling lubricant is very important. To reduce the costs of production and to make the processes environmentally safe, the goal is to move toward dry cutting by eliminating cutting fluids. This goal can be achieved by using coated carbide tool and by increasing cutting speed. The present paper firstly reviews the main works on surface integrity and especially residual stresses when machining Inconel 718 superalloy. It focuses then on the effect of dry machining on surface integrity. Wet and dry turning tests were performed at various cutting speeds, with semi-finishing conditions (0.5 mm depth of cut and 0.1 mm/rev feed rate) and using a coated carbide tool. For each cutting test, cutting force was measured, machined surface was observed, and residual stress profiles were determined. An optimal cutting speed of 60 m/min was determined, and additional measurements and observations were performed. Microhardness increment and the microstructure alteration beneath the machined surface were analysed. It is demonstrated that dry machining with a coated carbide tool leads to potentially acceptable surface quality with residual stresses and microhardness values in the machining affected zone of the same order than those obtained in wet conditions when using the optimised cutting speed value; in addition, no severe microstructure alteration was depicted.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
The machinability of nickel-based alloys: a review
Ezugwu, E. O., Wang, Z. M., & Machado, A. R. (1999) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(98)00314-8 · Cited by 857
A review of developments towards dry and high speed machining of Inconel 718 alloy
Dudzinski, D., Devillez, A., Moufki, A., Larrouquère, D., Zerrouki, V, & Vigneau, J. (2004) · International Journal of Machine Tools and Manufacture · doi:10.1016/s0890-6955(03)00159-7 · Cited by 716
Self-citationCutting forces and wear in dry machining of Inconel 718 with coated carbide tools
Devillez, A., Schneider, F., Dominiak, S., Dudzinski, D., & Larrouquere, D. (2007) · Wear · doi:10.1016/j.wear.2006.10.009 · Cited by 377
Self-citationHigh speed MQL finish-turning of Inconel 718 with different coated tools
Kamata, Y., & Obikawa, T. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2007.04.052 · Cited by 318
An analysis of the residual stresses generated in Inconel 718™ when turning
Sharman, A. R. C., Hughes, J. I., & Ridgway, K. (2006) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2005.12.007 · Cited by 269
Surface integrity when machining age hardened Inconel 718 with coated carbide cutting tools
Arunachalam, R. M., Mannan, M. A., & Spowage, A. C. (2004) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2004.05.005 · Cited by 244
Guo, Y. B., Li, W., & Jawahir, I. S. (2009) · Machining Science and Technology · doi:10.1080/10910340903454922 · Cited by 221
Analysis of residual stresses induced by dry turning of difficult-to-machine materials
Outeiro, J. C., Pina, J. C., M'Saoubi, R., Pusavec, F., & Jawahir, I. S. (2008) · CIRP Annals · doi:10.1016/j.cirp.2008.03.076 · Cited by 204
Estimating cutting force from rotating and stationary feed motor currents on a milling machine
Jeong, Y.-H., & Cho, D. (2002) · International Journal of Machine Tools and Manufacture · doi:10.1016/s0890-6955(02)00082-2 · Cited by 134
Sharman, A. R. C., Hughes, J., & Ridgway, K. (2008) · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · doi:10.1243/09544054jem936 · Cited by 110
Cited by
Environmental friendly cutting fluids and cooling techniques in machining: a review
Debnath, S., Reddy, M. M., & Yi, Q. S. (2014) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2014.07.071 · Cited by 812
State-of-the-art in surface integrity in machining of nickel-based super alloys
Thakur, A., & Gangopadhyay, S. (2016) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2015.10.001 · Cited by 698
State-of-The-Art Cooling and Lubrication for Machining Inconel 718
De Bartolomeis, A., Newman, S. T., Biermann, D., & Shokrani, A. (2021) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4047842 · Cited by 43
Gong, L., Bertolini, R., Bruschi, S., Ghiotti, A., & He, N. (2022) · International Journal of Precision Engineering and Manufacturing-Green Technology · doi:10.1007/s40684-021-00310-1 · Cited by 34
Metadata
- Authors
- Devillez, A., Le Coz, G., Dominiak, S., & Dudzinski, D.
- Venue
- Journal of Materials Processing Technology
- Publisher
- Elsevier BV
- Published
- 2011-10
- Volume
- 211
- Issue
- 10
- Pages
- 1590-1598
- ISSN
- 0924-0136 (ISSN-L)
- OpenAlex
- W1965308830
- Cited by
- 391
- References
- 12
- FWCI
- 33.58
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.