The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Wire + Arc Additive Manufacture of 17-4 PH stainless steel: Effect of different processing conditions on microstructure, hardness, and tensile strength
Open accessAbstract
Abstract Wire + Arc Additive Manufacture (WAAM) is receiving increasing attention as it offers a way to fabricate meter scale parts, with relatively low capital cost, lower material wastage and logistical advantages. A wide range of metallic alloys could be manufactured using this process. Martensitic grade precipitation-hardening stainless steel 17-4 PH offers excellent combination of high strength and corrosion resistance. Hence, it is important to investigate the behaviour of this alloy in WAAM. In the present work, the effect of different process variables such as shielding gas, deposition path and post-fabrication heat treatment, on microstructure and mechanical properties were studied. A number of specimens were manufactured by WAAM using the Fronius Cold Metal Transfer (CMT) process under different controlled processing conditions. These specimens were subsequently characterized by optical and electron microscopy and mechanical properties in terms of tensile strength and hardness. It was found that using shielding gases that result in higher heat input reduces the amount of retained austenite in the as-deposited microstructure. It has been demonstrated that the required tensile properties can be achieved by applying post-deposition heat treatment. However, it is suggested that direct aging in as deposited condition resulted in formation of harmful intermetallic phases which embrittles the deposit.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Cited by
Steels in additive manufacturing: A review of their microstructure and properties
Bajaj, P., Hariharan, A., Kini, A., Kürnsteiner, P., Raabe, D., & Jägle, E. A. (2020) · Materials Science and Engineering: A · doi:10.1016/j.msea.2019.138633 · Cited by 1,020
Additive manufacturing of steels: a review of achievements and challenges
Haghdadi, N., Laleh, M., Moyle, M., & Primig, S. (2021) · Journal of Materials Science · doi:10.1007/s10853-020-05109-0 · Cited by 622
Metal additive manufacturing in structural engineering – review, advances, opportunities and outlook
Gardner, L. (2023) · Structures · doi:10.1016/j.istruc.2022.12.039 · Cited by 398
Wire Arc Additive Manufacturing of Stainless Steels: A Review
Jin, W., Zhang, C., Jin, S., Tian, Y., Wellmann, D., & Liu, W. (2020) · Applied Sciences · doi:10.3390/app10051563 · Cited by 388
Metadata
- Authors
- Caballero, A., Ding, J., Ganguly, S., & Williams, S.
- Venue
- Journal of Materials Processing Technology
- Publisher
- Elsevier BV
- Published
- 2019-06
- Volume
- 268
- Pages
- 54-62
- ISSN
- 0924-0136 (ISSN-L)
- OpenAlex
- W2910349200
- Cited by
- 173
- References
- 1
- FWCI
- 10.75
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Wire + Arc Additive Manufacture of 17-4 PH stainless steel: Effect of different processing conditions on microstructure, hardness, and tensile strength. https://app.cochat.ai/papers/10.1016/j.jmatprotec.2019.01.007
- The paper
- Caballero, A., Ding, J., Ganguly, S., & Williams, S. (2019). Wire + Arc Additive Manufacture of 17-4 PH stainless steel: Effect of different processing conditions on microstructure, hardness, and tensile strength. Journal of Materials Processing Technology. https://doi.org/10.1016/j.jmatprotec.2019.01.007
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.