The DOI matches its Crossref record; 5 of the 5 references it cites were found in a registry or an index.
Shear strength criteria for rock, rock joints, rockfill and rock masses: Problems and some solutions
Open accessAbstract
Although many intact rock types can be very strong, a critical confining pressure can eventually be reached in triaxial testing, such that the Mohr shear strength envelope becomes horizontal. This critical state has recently been better defined, and correct curvature or correct deviation from linear Mohr–Coulomb (M-C) has finally been found. Standard shear testing procedures for rock joints, using multiple testing of the same sample, in case of insufficient samples, can be shown to exaggerate apparent cohesion. Even rough joints do not have any cohesion, but instead have very high friction angles at low stress, due to strong dilation. Rock masses, implying problems of large-scale interaction with engineering structures, may have both cohesive and frictional strength components. However, it is not correct to add these, following linear M-C or nonlinear Hoek–Brown (H-B) standard routines. Cohesion is broken at small strain, while friction is mobilized at larger strain and remains to the end of the shear deformation. The criterion ‘c then σn tan φ’ should replace ‘c plus σntan φ’ for improved fit to reality. Transformation of principal stresses to a shear plane seems to ignore mobilized dilation, and caused great experimental difficulties until understood. There seems to be plenty of room for continued research, so that errors of judgement of the last 50 years can be corrected.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Engineering classification of rock masses for the design of tunnel support
Barton, N., Lien, R., & Lunde, J. (1974) · Rock Mechanics Felsmechanik M�canique des Roches · doi:10.1007/bf01239496 · Cited by 2,979
Self-citationReview of a new shear strength criterion for rock joints
Barton, N. R. (1973) · International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts · doi:10.1016/0148-9062(74)90491-4 · Cited by 1,693
Self-citationSome new Q-value correlations to assist in site characterisation and tunnel design
Barton, N. (2002) · International Journal of Rock Mechanics and Mining Sciences · doi:10.1016/s1365-1609(02)00011-4 · Cited by 893
Self-citationModified Mohr–Coulomb criterion for non-linear triaxial and polyaxial strength of jointed rocks
Singh, M., & Singh, B. (2012) · International Journal of Rock Mechanics and Mining Sciences · doi:10.1016/j.ijrmms.2011.12.007 · Cited by 193
Barton, N. R., & Pandey, S. K. (2011) · International Journal of Rock Mechanics and Mining Sciences · doi:10.1016/j.ijrmms.2011.07.002 · Cited by 41
Self-citation
Cited by
Frictional behaviour of timber-concrete contact pairs
Jaaranen, J., & Fink, G. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.118273 · Cited by 22
Metadata
- Authors
- Barton, N.
- Venue
- Journal of Rock Mechanics and Geotechnical Engineering
- Publisher
- Elsevier BV
- Published
- 2013-08
- Volume
- 5
- Issue
- 4
- Pages
- 249-261
- ISSN
- 1674-7755 (ISSN-L)
- OpenAlex
- W2136268613
- Cited by
- 414
- References
- 5
- FWCI
- 18.81
- Type
- journal article
- Language
- en
- Open access
- diamond
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Shear strength criteria for rock, rock joints, rockfill and rock masses: Problems and some solutions. https://app.cochat.ai/papers/10.1016/j.jrmge.2013.05.008
- The paper
- Barton, N. (2013). Shear strength criteria for rock, rock joints, rockfill and rock masses: Problems and some solutions. Journal of Rock Mechanics and Geotechnical Engineering. https://doi.org/10.1016/j.jrmge.2013.05.008
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.