The DOI matches its Crossref record; 15 of the 15 references it cites were found in a registry or an index.
Microstructure of selective laser melted CM247LC nickel-based superalloy and its evolution through heat treatment
Open accessAbstract
The selective laser melting of high temperature alloys is of great interest to the aerospace industry as it offers the prospect of producing more complex geometries than can be achieved with other manufacturing methods. In this study, the microstructure of the nickel-based superalloy, CM247LC, has been characterised following selective laser melting and after a post deposition heat treatment below the γʹ solvus temperature. In the as-deposited state, scanning electron microscopy with electron backscatter diffraction revealed a fine, cellular microstructure with preferential alignment of 〈001〉 along the build direction. A high dislocation density was seen at the periphery of the cells, indicating substantial localised deformation of the material. Fine primary MC carbides were also observed in the inter-cellular regions. High-resolution transmission electron microscopy identified the occurrence of very fine γʹ precipitates, approximately 5 nm in diameter, dispersed within the gamma phase. After heat treatment, the elongated cell colonies were observed to partially coalesce, accompanied by a decrease in dislocation density, producing columnar grains along the build direction. Cuboidal γʹ precipitates approximately 500 nm in diameter were observed to form in the recrystallised grains, accompanied by larger γʹ precipitates on the grain boundaries.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Laser additive manufacturing of metallic components: materials, processes and mechanisms
Gu, D. D., Meiners, W., Wissenbach, K., & Poprawe, R. (2012) · International Materials Reviews · doi:10.1179/1743280411y.0000000014 · Cited by 3,197
Progress in Additive Manufacturing and Rapid Prototyping
Kruth, J.-P., Leu, M. C., & Nakagawa, T. (1998) · CIRP Annals · doi:10.1016/s0007-8506(07)63240-5 · Cited by 1,331
Microstructures and mechanical behavior of Inconel 718 fabricated by selective laser melting
Amato, K. N., Gaytan, S. M., Murr, L. E., Martinez, E., Shindo, P. W., Hernandez, J., Collins, S., & Medina, F. (2012) · Acta Materialia · doi:10.1016/j.actamat.2011.12.032 · Cited by 1,166
Single-crystal laser deposition of superalloys: processing–microstructure maps
Gäumann, M., Bezençon, C., Canalis, P., & Kurz, W. (2001) · Acta Materialia · doi:10.1016/s1359-6454(00)00367-0 · Cited by 1,091
Dinda, G. P., Dasgupta, A. K., & Mazumder, J. (2009) · Materials Science and Engineering: A · doi:10.1016/j.msea.2009.01.009 · Cited by 858
Carter, L. N., Martin, C., Withers, P. J., & Attallah, M. M. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2014.06.172 · Cited by 751
Rapid manufacturing of metal components by laser forming
Santos, E. C., Shiomi, M., Osakada, K., & Laoui, T. (2006) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2005.09.005 · Cited by 740
Zhang, D., Niu, W., Cao, X., & Liu, Z. (2015) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.06.021 · Cited by 723
Microstructural and texture development in direct laser fabricated IN718
Parimi, L. L., Ravi, G. A., Clark, D., & Attallah, M. M. (2014) · Materials Characterization · doi:10.1016/j.matchar.2013.12.012 · Cited by 565
Evolution of solidification texture during additive manufacturing
Wei, H. L., Mazumder, J., & DebRoy, T. (2015) · Scientific Reports · doi:10.1038/srep16446 · Cited by 557
Kunze, K., Etter, T., Grässlin, J., & Shklover, V. (2014) · Materials Science and Engineering A · doi:10.1016/j.msea.2014.10.003 · Cited by 515
Texture control during laser deposition of nickel-based superalloy
Dinda, G. P., Dasgupta, A. K., & Mazumder, J. (2012) · Scripta Materialia · doi:10.1016/j.scriptamat.2012.06.014 · Cited by 471
Kanagarajah, P., Brenne, F., Niendorf, T., & Maier, H. J. (2013) · Materials Science and Engineering: A · doi:10.1016/j.msea.2013.09.025 · Cited by 318
Laser welding of dissimilar metal combinations
Sun, Z., & Ion, J. C. (1995) · Journal of Materials Science · doi:10.1007/bf00361499 · Cited by 291
Shaped metal deposition of a nickel alloy for aero engine applications
Clark, D., Bache, M. R., & Whittaker, M. T. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2007.10.051 · Cited by 245
Cited by
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Alloys-by-design: Application to new superalloys for additive manufacturing
Tang, Y. T., Panwisawas, C., Ghoussoub, J. N., Gong, Y., Clark, J. W. G., Németh, A. A. N., McCartney, D. G., & Reed, R. C. (2021) · Acta Materialia · doi:10.1016/j.actamat.2020.09.023 · Cited by 678
Powder Bed Fusion of nickel-based superalloys: A review
Sanchez, S., Smith, P., Xu, Z., Gaspard, G., Hyde, C. J., Wits, W. W., Ashcroft, I. A., Chen, H., & Clare, A. T. (2021) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2021.103729 · Cited by 541
Mostafaei, A., Ghiaasiaan, R., Ho, I.-T., Strayer, S., Chang, K.-C., Shamsaei, N., Shao, S., Paul, S., Yeh, A.-C., Tin, S., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101108 · Cited by 531
Defects and anomalies in powder bed fusion metal additive manufacturing
Mostafaei, A., Zhao, C., He, Y., Reza Ghiaasiaan, S., Shi, B., Shao, S., Shamsaei, N., Wu, Z., Kouraytem, N., Sun, T., et al. (2022) · Current Opinion in Solid State and Materials Science · doi:10.1016/j.cossms.2021.100974 · Cited by 491
Metadata
- Authors
- Divya, V. D., Muñoz-Moreno, R., Messé, O. M. D. M., Barnard, J. S., Baker, S., Illston, T., & Stone, H. J.
- Venue
- Materials Characterization
- Publisher
- Elsevier BV
- Published
- 2016-04
- Volume
- 114
- Pages
- 62-74
- ISSN
- 1044-5803 (ISSN-L)
- OpenAlex
- W2287331356
- Cited by
- 280
- References
- 15
- FWCI
- 14.76
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.