The DOI matches its Crossref record; 44 of the 44 references it cites were found in a registry or an index.
Mechanical and microstructural testing of wire and arc additively manufactured sheet material
Open accessAbstract
Wire and arc additive manufacturing (WAAM) is a method of 3D printing that enables large elements to be built, with reasonable printing times and costs. There are, however, uncertainties relating to the structural performance of WAAM material, including the basic mechanical properties, the degree of anisotropy, the influence of the as-built geometry and the variability in response. Towards addressing this knowledge gap, a comprehensive series of tensile tests on WAAM stainless steel was conducted; the results are presented herein. As-built and machined coupons were tested to investigate the influence of the geometrical irregularity on the stress-strain characteristics, while material anisotropy was explored by testing coupons produced at different angles to the printing orientation. Non-contact measurement techniques were employed to determine the geometric properties and deformation fields of the specimens, while sophisticated analysis methods were used for post processing the test data. The material response revealed a significant degree of anisotropy, explained by the existence of a strong crystallographic texture, uncovered by means of electron backscatter diffraction. Finally, the effective mechanical properties of the as-built material were shown to be strongly dependent on the geometric variability; simple geometric measures were therefore developed to characterise the key aspects of the observed behaviour.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
An Algorithm for Least-Squares Estimation of Nonlinear Parameters
Marquardt, D. W. (1963) · Journal of the Society for Industrial and Applied Mathematics · doi:10.1137/0111030 · Cited by 30,728
A method for the solution of certain non-linear problems in least squares
Levenberg, K. (1944) · Quarterly of Applied Mathematics · doi:10.1090/qam/10666 · Cited by 12,359
LIII. On lines and planes of closest fit to systems of points in space
Pearson, K. (1901) · The London, Edinburgh, and Dublin Philosophical Magazine and Journal of Science · doi:10.1080/14786440109462720 · Cited by 11,934
Analysis of a complex of statistical variables into principal components.
Hotelling, H. (1933) · Journal of Educational Psychology · doi:10.1037/h0071325 · Cited by 9,633
The Deformation and Ageing of Mild Steel: III Discussion of Results
Hall, E. O. (1951) · Proceedings of the Physical Society. Section B · doi:10.1088/0370-1301/64/9/303 · Cited by 7,872
A Flexible Growth Function for Empirical Use
RICHARDS, F. J. (1959) · Journal of Experimental Botany · doi:10.1093/jxb/10.2.290 · Cited by 4,146
The Cleavage Strength of Polycrystals
Petch, N. J. (1953) · Medical Entomology and Zoology · Cited by 3,641
The status, challenges, and future of additive manufacturing in engineering
Gao, W., Zhang, Y., Ramanujan, D., Ramani, K., Chen, Y., Williams, C. B., Wang, C. C. L., Shin, Y. C., Zhang, S., & Zavattieri, P. D. (2015) · Computer-Aided Design · doi:10.1016/j.cad.2015.04.001 · Cited by 2,631
Zur Theorie der orthogonalen Funktionensysteme: Erste Mitteilung
Haar, A. (1910) · Mathematische Annalen · doi:10.1007/bf01456326 · Cited by 2,138
Additive manufacturing: technology, applications and research needs
Guo, N., & Leu, M. C. (2013) · Frontiers of Mechanical Engineering · doi:10.1007/s11465-013-0248-8 · Cited by 2,073
Cited by
Metal additive manufacturing in structural engineering – review, advances, opportunities and outlook
Gardner, L. (2023) · Structures · doi:10.1016/j.istruc.2022.12.039 · Cited by 398
Self-citationTesting and initial verification of the world's first metal 3D printed bridge
Gardner, L., Kyvelou, P., Herbert, G., & Buchanan, C. (2020) · Journal of Constructional Steel Research · doi:10.1016/j.jcsr.2020.106233 · Cited by 340
Self-citation
Metadata
- Authors
- Kyvelou, P., Slack, H., Daskalaki Mountanou, D., Wadee, M. A., Britton, T. B., Buchanan, C., & Gardner, L.
- Venue
- Materials & Design
- Publisher
- Elsevier BV
- Published
- 2020-07
- Volume
- 192
- Pages
- 108675
- ISSN
- 0264-1275 (ISSN-L)
- OpenAlex
- W3013475724
- Cited by
- 273
- References
- 44
- FWCI
- 13.84
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Mechanical and microstructural testing of wire and arc additively manufactured sheet material. https://app.cochat.ai/papers/10.1016/j.matdes.2020.108675
- The paper
- Kyvelou, P., Slack, H., Daskalaki Mountanou, D., Wadee, M. A., Britton, T. B., Buchanan, C., & Gardner, L. (2020). Mechanical and microstructural testing of wire and arc additively manufactured sheet material. Materials & Design. https://doi.org/10.1016/j.matdes.2020.108675
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.