The DOI matches its Crossref record; 14 of the 14 references it cites were found in a registry or an index; none of the 15 sources its claims cite is checked for support yet.
Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions
Open accessAbstract
Reliable discharge estimation is essential for water resource management, yet many regions lack sufficient hydrological stations. To address this limitation, we propose the Spatial Hydraulic Geometry Interpolation (SHGI) method, which estimates discharge (Q), hydraulic depth (D), and mean velocity (V) from river width (W) obtained via surveys or satellite imagery. SHGI integrates hydraulic geometry theory with multiquadric radial basis interpolation, applied to the Meta and Atrato river basins in Colombia. Parameters of at‑station hydraulic geometry (coefficients a , c, k and exponents b, f, m ) were derived using least squares and transformed into log‑ratio space to preserve their compositional constraints. Interpolation along upstream distance ensures spatial continuity, and closure operations guarantee internal consistency. Validation against observed data in basins with contrasting geomorphology and data density confirmed the method’s robustness. The principal contributions of SHGI are: • Longitudinal continuity: explicit incorporation of upstream distance to interpolate parameters consistently along channels and tributaries. • Compositional integrity: preservation of the multiplicative and additive constraints of hydraulic geometry parameters during interpolation. • Estimation under data scarcity: enabling calculation of Q, D, and V at ungauged sites using only river width.
Overview
CoChat Summary
TL;DR
The paper proposes Spatial Hydraulic Geometry Interpolation (SHGI), which estimates discharge (Q), hydraulic depth (D), and mean velocity (V) from river width (W) by interpolating at-station hydraulic geometry parameters with multiquadric radial basis functions in log-ratio space. Validation in Colombia’s Meta and Atrato basins shows better performance in the denser Meta network, with mean velocity the most error-prone variable.
Key findings
- SHGI estimates Q, D, and V from W alone after least-squares at-station parameter estimation, centered log-ratio transformation, multiquadric interpolation along upstream distance, and closure constraints; validation used the Meta (average annual discharge 6614 m³/s) and Atrato (2550 m³/s) basins.
- In the Meta basin, interpolation MAPE at four control stations was Q: 1.06, 1.04, 0.58, 1.59; D: 0.41, 0.47, 0.48, 0.56; V: 0.71, 0.41, 0.42, 1.6. In the Atrato basin, interpolation MAPE was Q: 0.72, 0.38, 2.09, 0.88; D: 0.56, 0.51, 0.24, 0.27; V: 0.39, 0.50, 1.90, 0.87.
- Interpolation improved over station hydraulic geometry regression in the Meta basin for Q and V at most stations; in the Atrato basin it did not, e.g., Aguasal Q 0.71% → 2.09% and V 0.37% → 1.90%, and Pte. Sánchez Q 0.42% → 0.88% and V 0.23% → 0.87%.
- Mean coefficient errors were Meta: a = 29.87%, c = 56.74%, k = 149.09%; Atrato: a = 66.03%, c = 56.41%, k = 200.58%; mean velocity showed the greatest dispersion and error.
Methods
- Design: method paper formalizing SHGI in sequential steps: collect historical discharge at upstream/downstream stations; estimate a, b, c, f, k, m by least squares; apply centered log-ratio transformation; interpolate parameters along upstream distance using multiquadric radial basis functions; apply multiplicative and additive closures; compute Q, D, and V from W.
- Data/sample: historical streamflow records from Ideam stations in the Meta and Atrato river basins, Colombia; the text reports 13 Atrato and 46 Meta stations for analysis (18 Meta main-channel and 28 tributary; 8 Atrato main-channel and 5 tributary), with cross-validation at four stations per basin.
- Analysis: smoothing parameter values 0.1–0.5 were evaluated by RMSE, and a uniform value of 0.5 was adopted for all parameters; performance was compared via MAPE against at-station hydraulic geometry regression.
Limitations
- Stated: accuracy decreases in tributary zones; the method requires historical discharge records upstream and downstream of the target site; coefficients a, c, and k are highly variable and sensitive to calibration; log-ratio transformation adds implementation complexity; mean velocity is the most dispersed and error-prone variable; performance drops significantly when station density is low.
- Evident: station counts are inconsistent across the text (Atrato 13 vs. 9; Meta 46 vs. 48 vs. 44), complicating interpretation of the validation.
- Evident: Table 12’s descriptive statistics for exponents b, f, and m are identical to Table 8’s for coefficients a, c, and k, suggesting a possible reporting error.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures


























Verification
Claims the paper makes
0 Valid · 1 Not valid · 13 Not checked · 55 Own results and interpretations
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Limitations in mean velocity estimation: Mean velocity is the variable with the greatest dispersion and error in the estimates, suggesting that the model does not fully capture its spatial behavior.”
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Limitations
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“For coefficient c, the errors were similar in both basins, while for k, high errors were observed in both basins.”
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Method validation
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Overall, the results indicate that, although the model presents systematic biases, especially in the estimation of average velocity, its compositional structure and spatial adaptability make it a suitable tool for applications in contexts with scarce data, provided that its limitations are recognized and complemented with local validations.”
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Method validation
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“SHGI integrates hydraulic geometry theory with multiquadric radial basis interpolation, applied to the Meta and Atrato river basins in Colombia.”
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Abstract
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Table 8, Table 9 summarize the descriptive statistics of the percentage estimation errors, indicating that the model performs more reliably in the Meta River basin compared to the Atrato River basin.”
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Method validation
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
28 more claims
Create a free account to see all 69 claims and to verify the 15 references still open.
- It may state two separate claims as one. 19
- Probably not a substantial claim. 22
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Method validation
“two on tributaries: Aguasal (code 11,017,010) and Puente Las Sánchez (code 11,027,010).”
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Method validation
“| 11,027,010 | 5.51 | −76.10 | 8.76 | 0.31 | 0.17 | 0.39 | 0.65 | 0.30 | 27.94 | Atrato |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Method validation
“13 stations were analyzed in the Atrato basin, compared to 48 stations in the Meta basin”
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Method validation
“Streamflow data from 13 stations in the Atrato River basin and 46 hydrological stations in the Meta River basin”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Method validation
“The results show that multiquadratic interpolation offers a more consistent fit in estimating discharge (Q) and average velocity (V), with lower MAPE values at most stations.”
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Method validation
“| Aguaverde | 1.06 | 0.41 | 0.71 | 1.04 | 0.45 | 0.41 | | Pto Texas | 1.04 | 0.47 | 0.41 | 2.02 | 0.76 | 0.71 | | El Palmar | 0.58 | 0.48 | 0.42 | 0.98 | 0.29 | 0.55 | | La Esperanza | 1.59 | 0.56 | 1.6 | 2.30 | 0.60 | 0.77 |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
“| 35,127,020 | 4.34 | −72.16 | 22.10 | 0.22 | 0.51 | 0.38 | 0.50 | 0.38 | 69.56 | Tributary |”
§ Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions✰✰✰ > Method validation
Reported 1 · recomputed 5.6355
Citations
Cites
The hydraulic geometry of stream channels and some physiographic implications
Leopold, L. B., & Maddock, T. (1953) · Professional Paper · doi:10.3133/pp252 · Cited by 2,966
Multiquadric equations of topography and other irregular surfaces
Hardy, R. L. (1971) · Journal of Geophysical Research · doi:10.1029/jb076i008p01905 · Cited by 2,358
Gleason, C. J., & Smith, L. C. (2014) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1317606111 · Cited by 387
Generalized Linear Models: With Applications in Engineering and the Sciences
Myers, R. H., Montgomery, D. C., Vining, G. G., & Robinson, T. J. (2010) · Wiley series in probability and statistics · doi:10.1002/9780470556986 · Cited by 313
Predicting stream temperatures: geostatistical model comparison using alternative distance metrics
Gardner, B., Sullivan, P. J., & Lembo, A. J. (2003) · Canadian Journal of Fisheries and Aquatic Sciences · doi:10.1139/f03-025 · Cited by 112
Analytical derivation of at-a-station hydraulic-geometry relations
Lawrence, D. (2007) · Journal of Hydrology · doi:10.1016/j.jhydrol.2006.09.021 · Cited by 102
Adaptive Interpolation by Scaled Multiquadrics
Bozzini, M., Lenarduzzi, L., & Schaback, R. (2002) · Advances in Computational Mathematics · doi:10.1023/a:1014584220418 · Cited by 48
The hydraulic geometry of stream channels and some physiographic implications,
Leopold, L. B., & Maddock, T. (1953) · University of Michigan Library Repository · Cited by 35
Chen, C., Li, Y., Yan, C., Dai, H., & Liu, G. (2015) · Remote Sensing · doi:10.3390/rs70303347 · Cited by 22
Methods for interpolating stream width, depth, and current velocity
Kratzer, J. F., Hayes, D. B., & Thompson, B. E. (2006) · Ecological Modelling · doi:10.1016/j.ecolmodel.2006.02.004 · Cited by 18
Research works printed but not linked: 1
- Tolosana-Delgado, 2008, Compositional data analysis in a nutshell, Statistics
Cited by
Still being checked.
Metadata
- Authors
- Zamudio-Huertas, E., García-Ubaque, C. A., & Obregón-Neira, N.
- Affiliations
- Universidad Distrital Francisco José de Caldas (CO)
- Corresponding author
- Zamudio-Huertas, Eduardo
- Venue
- MethodsX
- Publisher
- Elsevier BV
- Published
- 2026-06
- Volume
- 16
- Pages
- 103804
- ISSN
- 2215-0161 (ISSN-L)
- PMC
- PMC12878605
- OpenAlex
- W7125617318
- Cited by
- 0
- References
- 14
- FWCI
- 0.00
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- www.elsevier.com/tdm/userlicense/1.0/ (tdm)
- www.elsevier.com/legal/tdmrep-license (tdm)
- creativecommons.org/licenses/by/4.0/ (vor)
- Locations
- MethodsX (publishedVersion, cc-by)
- SSRN Electronic Journal (submittedVersion)
- PubMed Central (publishedVersion, cc-by)
- Europe PMC (PubMed Central) (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Funders
- Pontificia Universidad Javeriana
- Topics
- Physical Sciences › Environmental Science › Water Science and Technology › Hydrology and Watershed Management Studies
- Physical Sciences › Earth and Planetary Sciences › Earth-Surface Processes › Hydrology and Sediment Transport Processes
- Physical Sciences › Environmental Science › Global and Planetary Change › Flood Risk Assessment and Management
- Keywords
- discharge estimation, hydraulic geometry, spatial interpolation, river width, ungauged sites, data-scarce regions, multiquadric radial basis functions, compositional data, mean velocity, Atrato River basin
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-11-19, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-11-19 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions. https://app.cochat.ai/papers/10.1016/j.mex.2026.103804
- The paper
- Zamudio-Huertas, E., García-Ubaque, C. A., & Obregón-Neira, N. (2026). Method for estimating discharge, hydraulic depth, and mean velocity in rivers through spatial interpolation of at-a-station hydraulic geometry in data- scarce regions. MethodsX. https://doi.org/10.1016/j.mex.2026.103804
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.