The DOI matches its Crossref record; 6 of the 6 references it cites were found in a registry or an index.
Effects of processing on microstructure and properties of SLS Nylon 12
Open accessAbstract
There currently exists the requirement to improve reproducibility and mechanical properties of SLS Nylon parts for rapid manufacturing (RM). In order to achieve this, further fundamental research is needed and this paper addresses this need by investigating effects of potential sources of the lack of reproducibility and reports effects in relation to crystal structure, microstructure, chemical structure (molecular weight) and mechanical properties. Different γ crystal forms were identified and related to the unmolten particle cores and the melted/crystallised regions of the microstructure. The melt point of the γ-form varied depending on processing conditions. Observable differences were also present when comparing the microstructure of the parts. Molecular weight of parts was significantly higher than virgin powder but used powder also showed an increase in molecular weight. This was related to improved elongation at break of parts built from the used powder, consistent with previous studies. Tensile strength showed some increase with machine parameters selected for improved strength but Young's modulus values were broadly similar.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Lasers and materials in selective laser sintering
Kruth, J. P., Wang, X., Laoui, T., & Froyen, L. (2003) · Assembly Automation · doi:10.1108/01445150310698652 · Cited by 826
Rapid Manufacturing: An Industrial Revolution for the Digital Age
(2005) · Wiley eBooks · doi:10.1002/0470033991 · Cited by 679
Schoch, K. F. (1996) · IEEE Electrical Insulation Magazine · doi:10.1109/mei.1996.537196 · Cited by 606
Material properties and fabrication parameters in selective laser sintering process
Gibson, I., & Shi, D. (1997) · Rapid Prototyping Journal · doi:10.1108/13552549710191836 · Cited by 488
Kohan, M. I. (1995) · Medical Entomology and Zoology · Cited by 415
Density prediction of crystalline polymer sintered parts at various powder bed temperatures
Tontowi, A. E., & Childs, T. H. C. (2001) · Rapid Prototyping Journal · doi:10.1108/13552540110395637 · Cited by 137
Cited by
Polymers for 3D Printing and Customized Additive Manufacturing
Ligon, S. C., Liska, R., Stampfl, J., Gurr, M., & Mülhaupt, R. (2017) · Chemical Reviews · doi:10.1021/acs.chemrev.7b00074 · Cited by 3,741
Consolidation phenomena in laser and powder-bed based layered manufacturing
Kruth, J.-P., Levy, G., Klocke, F., & Childs, T. H. C. (2007) · CIRP Annals · doi:10.1016/j.cirp.2007.10.004 · Cited by 1,444
Mechanical characterization of 3D-printed polymers
Dizon, J. R. C., Espera, A. H., Chen, Q., & Advincula, R. C. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2017.12.002 · Cited by 1,340
A review on additive manufacturing of polymer-fiber composites
Parandoush, P., & Lin, D. (2017) · Composite Structures · doi:10.1016/j.compstruct.2017.08.088 · Cited by 1,270
Polygerinos, P., Correll, N., Morin, S. A., Mosadegh, B., Onal, C. D., Petersen, K., Cianchetti, M., Tolley, M. T., & Shepherd, R. F. (2017) · Advanced Engineering Materials · doi:10.1002/adem.201700016 · Cited by 1,063
Metadata
- Authors
- Zarringhalam, H., Hopkinson, N., Kamperman, N. F., & de Vlieger, J. J.
- Venue
- Materials Science and Engineering: A
- Publisher
- Elsevier BV
- Published
- 2006-11
- Volume
- 435-436
- Pages
- 172-180
- ISSN
- 0921-5093 (ISSN-L)
- OpenAlex
- W1998791639
- Cited by
- 295
- References
- 6
- FWCI
- 19.66
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effects of processing on microstructure and properties of SLS Nylon 12. https://app.cochat.ai/papers/10.1016/j.msea.2006.07.084
- The paper
- Zarringhalam, H., Hopkinson, N., Kamperman, N. F., & de Vlieger, J. J. (2006). Effects of processing on microstructure and properties of SLS Nylon 12. Materials Science and Engineering: A. https://doi.org/10.1016/j.msea.2006.07.084
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.