The DOI matches its Crossref record.
Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V
Open accessAbstract
Recent research on the additive manufacturing (AM) of Ti alloys has shown that the mechanical properties of the parts are affected by the characteristic microstructure that originates from the AM process . To understand the effect of the microstructure on the tensile properties , selective laser melted (SLM) Ti–6Al–4V samples built in three different orientations were tensile tested. The investigated samples were near fully dense, in two distinct conditions, as-built and stress relieved. It was found that the build orientation affects the tensile properties , and in particular the ductility of the samples. The mechanical anisotropy of the parts was discussed in relation to the crystallographic texture , phase composition and the predominant fracture mechanisms . Fractography and electron backscatter diffraction (EBSD) results indicate that the predominant fracture mechanism is intergranular fracture present along the grain boundaries and thus provide and explain the typical fracture surface features observed in fracture AM Ti–6Al–4V.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Defect formation mechanisms in selective laser melting: a review
Zhang, B., Li, Y., & Bai, Q. (2017) · Chinese Journal of Mechanical Engineering · doi:10.1007/s10033-017-0121-5 · Cited by 924
A review of topology optimization for additive manufacturing: Status and challenges
ZHU, J., ZHOU, H., WANG, C., ZHOU, L., YUAN, S., & ZHANG, W. (2021) · Chinese Journal of Aeronautics · doi:10.1016/j.cja.2020.09.020 · Cited by 874
Defining the tensile properties of Al-12Si parts produced by selective laser melting
Prashanth, K. G., Scudino, S., & Eckert, J. (2017) · Acta Materialia · doi:10.1016/j.actamat.2016.12.044 · Cited by 382
Fatemi, A., Molaei, R., Sharifimehr, S., Phan, N., & Shamsaei, N. (2017) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2017.03.044 · Cited by 282
Metadata
- Authors
- Simonelli, M., Tse, Y. Y., & Tuck, C.
- Venue
- Materials Science and Engineering: A
- Publisher
- Elsevier BV
- Published
- 2014-10
- Volume
- 616
- Pages
- 1-11
- ISSN
- 0921-5093 (ISSN-L)
- OpenAlex
- W2049039109
- Cited by
- 1,010
- References
- 0
- FWCI
- 38.18
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V. https://app.cochat.ai/papers/10.1016/j.msea.2014.07.086
- The paper
- Simonelli, M., Tse, Y. Y., & Tuck, C. (2014). Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V. Materials Science and Engineering: A. https://doi.org/10.1016/j.msea.2014.07.086
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.
