The DOI matches its Crossref record; 33 of the 33 references it cites were found in a registry or an index.
Comparative study of the microstructures and mechanical properties of direct laser fabricated and arc-melted Al x CoCrFeNi high entropy alloys
Open accessAbstract
Abstract High entropy alloys (HEA) are a relatively new metal alloy system that have promising potential in high temperature applications. These multi-component alloys are typically produced by arc-melting, requiring several remelts to achieve chemical homogeneity. Direct laser fabrication (DLF) is a rapid prototyping technique, which produces complex components from alloy powder by selectively melting micron-sized powder in successive layers. However, studies of the fabrication of complex alloys from simple elemental powder blends are sparse. In this study, DLF was employed to fabricate bulk samples of three alloys based on the Al x CoCrFeNi HEA system, where x was 0.3, 0.6 and 0.85 M fraction of Al. This produced FCC, FCC/BCC and BCC crystal structures, respectively. Corresponding alloys were also produced by arc-melting, and all microstructures were characterised and compared longitudinal and transverse to the build/solidification direction by x-ray diffraction, glow discharge optical emission spectroscopy and scanning electron microscopy (EDX and EBSD). Strong similarities were observed between the single phase FCC and BCC alloys produced by both techniques, however the FCC/BCC structures differed significantly. This has been attributed to a difference in the solidification rate and thermal gradient in the melt pool between the two different techniques. Room temperature compression testing showed very similar mechanical behaviour and properties for the two different processing routes. DLF was concluded to be a successful technique to manufacture bulk HEA׳s.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Yeh, J. ‐., Chen, S. ‐., Lin, S. ‐., Gan, J. ‐., Chin, T. ‐., Shun, T. ‐., Tsau, C. ‐., & Chang, S. ‐. (2004) · Advanced Engineering Materials · doi:10.1002/adem.200300567 · Cited by 15,281
Microstructural development in equiatomic multicomponent alloys
Cantor, B., Chang, I. T. H., Knight, P., & Vincent, A. J. B. (2004) · Materials Science and Engineering: A · doi:10.1016/j.msea.2003.10.257 · Cited by 10,130
Microstructures and properties of high-entropy alloys
Zhang, Y., Zuo, T. T., Tang, Z., Gao, M. C., Dahmen, K. A., Liaw, P. K., & Lu, Z. P. (2014) · Progress in Materials Science · doi:10.1016/j.pmatsci.2013.10.001 · Cited by 7,128
Takeuchi, A., & Inoue, A. (2005) · MATERIALS TRANSACTIONS · doi:10.2320/matertrans.46.2817 · Cited by 4,909
Prediction of high-entropy stabilized solid-solution in multi-component alloys
Yang, X., & Zhang, Y. (2012) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2011.11.021 · Cited by 2,920
Effect of valence electron concentration on stability of fcc or bcc phase in high entropy alloys
Guo, S., Ng, C., Lu, J., & Liu, C. T. (2011) · Journal of Applied Physics · doi:10.1063/1.3587228 · Cited by 2,911
Non-crystalline Structure in Solidified Gold–Silicon Alloys
KLEMENT, W., WILLENS, R. H., & DUWEZ, P. (1960) · Nature · doi:10.1038/187869b0 · Cited by 2,808
Phase stability in high entropy alloys: Formation of solid-solution phase or amorphous phase
GUO, S., & LIU, C. T. (2011) · Progress in Natural Science: Materials International · doi:10.1016/s1002-0071(12)60080-x · Cited by 2,534
Sluggish diffusion in Co–Cr–Fe–Mn–Ni high-entropy alloys
Tsai, K.-Y., Tsai, M.-H., & Yeh, J.-W. (2013) · Acta Materialia · doi:10.1016/j.actamat.2013.04.058 · Cited by 2,366
Alloy Design Strategies and Future Trends in High-Entropy Alloys
Yeh, J.-W. (2013) · JOM · doi:10.1007/s11837-013-0761-6 · Cited by 1,786
Wang, W.-R., Wang, W.-L., Wang, S.-C., Tsai, Y.-C., Lai, C.-H., & Yeh, J.-W. (2012) · Intermetallics · doi:10.1016/j.intermet.2012.03.005 · Cited by 1,517
Yeh, J.-W., Lin, S.-J., Chin, T.-S., Gan, J.-Y., Chen, S.-K., Shun, T.-T., Tsau, C.-H., & Chou, S.-Y. (2004) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-006-0234-4 · Cited by 1,252
Calculations of Mixing Enthalpy and Mismatch Entropy for Ternary Amorphous Alloys
Takeuchi, A., & Inoue, A. (2000) · Materials Transactions, JIM · doi:10.2320/matertrans1989.41.1372 · Cited by 882
Mechanical Properties and Stacking Fault Energies of NiFeCrCoMn High-Entropy Alloy
Zaddach, A. J., Niu, C., Koch, C. C., & Irving, D. L. (2013) · JOM · doi:10.1007/s11837-013-0771-4 · Cited by 878
High-Entropy Alloys – A New Era of Exploitation
Yeh, J. W., Chen, Y. L., Lin, S. J., & Chen, S. K. (2007) · Materials Science Forum · doi:10.4028/www.scientific.net/msf.560.1 · Cited by 658
Microstructural development during solidification of stainless steel alloys
Elmer, J. W., Allen, S. M., & Eagar, T. W. (1989) · Metallurgical Transactions A · doi:10.1007/bf02650298 · Cited by 600
Nanostructured nitride films of multi-element high-entropy alloys by reactive DC sputtering
Chen, T. K., Shun, T. T., Yeh, J. W., & Wong, M. S. (2004) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2004.08.023 · Cited by 587
Direct selective laser sintering of metals
Agarwala, M., Bourell, D., Beaman, J., Marcus, H., & Barlow, J. (1995) · Rapid Prototyping Journal · doi:10.1108/13552549510078113 · Cited by 571
Practical considerations and capabilities for laser assisted direct metal deposition
Lewis, G. K., & Schlienger, E. (2000) · Materials & Design (1980-2015) · doi:10.1016/s0261-3069(99)00078-3 · Cited by 484
Hollander, D. A., von Walter, M., Wirtz, T., Sellei, R., Schmidt-Rohlfing, B., Paar, O., & Erli, H.-J. (2006) · Biomaterials · doi:10.1016/j.biomaterials.2005.07.041 · Cited by 482
Electrical, magnetic, and Hall properties of AlxCoCrFeNi high-entropy alloys
Kao, Y.-F., Chen, S.-K., Chen, T.-J., Chu, P.-C., Yeh, J.-W., & Lin, S.-J. (2011) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2010.10.210 · Cited by 478
Alloying behavior in multi-component AlCoCrCuFe and NiCoCrCuFe high entropy alloys
Sathiyamoorthi, P., Murty, B. S., & Kottada, R. S. (2011) · Materials Science and Engineering A · doi:10.1016/j.msea.2011.11.044 · Cited by 424
Entropy-driven phase stability and slow diffusion kinetics in an Al0.5CoCrCuFeNi high entropy alloy
Ng, C., Guo, S., Luan, J., Shi, S., & Liu, C. T. (2012) · Intermetallics · doi:10.1016/j.intermet.2012.07.001 · Cited by 335
Kunce, I., Polanski, M., & Bystrzycki, J. (2013) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2013.05.071 · Cited by 273
Kunce, I., Polanski, M., & Bystrzycki, J. (2014) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2014.02.067 · Cited by 272
Direct metal laser sintering for rapid tooling: processing and characterisation of EOS parts
Khaing, M. W., Fuh, J. Y. H., & Lü, L. (2001) · Journal of Materials Processing Technology · doi:10.1016/s0924-0136(01)00584-2 · Cited by 261
Cheng, K.-H., Lai, C.-H., Lin, S.-J., & Yeh, J.-W. (2011) · Thin Solid Films · doi:10.1016/j.tsf.2010.11.034 · Cited by 237
Zhang, K., & Fu, Z. (2012) · Intermetallics · doi:10.1016/j.intermet.2011.10.010 · Cited by 217
Direct laser freeform fabrication of high performance metal components
Das, S., Beama, J. J., Wohlert, M., & Bourell, D. L. (1998) · Rapid Prototyping Journal · doi:10.1108/13552549810222939 · Cited by 131
Fu, Z., Chen, W., Fang, S., Zhang, D., Xiao, H., & Zhu, D. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2012.11.146 · Cited by 120
Damping behavior of AlxCoCrFeNi high-entropy alloys by a dynamic mechanical analyzer
Ma, S. G., Liaw, P. K., Gao, M. C., Qiao, J., Wang, Z., & Zhang, Y. (2014) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2014.03.050 · Cited by 112
Li, J., & Wang, H. M. (2010) · Materials Science and Engineering A · doi:10.1016/j.msea.2010.04.062 · Cited by 111
Nature of the interfaces between the constituent phases in the high entropy alloy CoCrCuFeNiAl
Welk, B. A., Williams, R. E. A., Viswanathan, G. B., Gibson, M. A., Liaw, P. K., & Fraser, H. L. (2013) · Ultramicroscopy · doi:10.1016/j.ultramic.2013.06.006 · Cited by 99
Cited by
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
High entropy alloys: A focused review of mechanical properties and deformation mechanisms
George, E. P., Curtin, W. A., & Tasan, C. C. (2020) · Acta Materialia · doi:10.1016/j.actamat.2019.12.015 · Cited by 1,917
Gorsse, S., Hutchinson, C., Gouné, M., & Banerjee, R. (2017) · Science and Technology of Advanced Materials · doi:10.1080/14686996.2017.1361305 · Cited by 920
Additive manufacturing of structural materials
Liu, G., Zhang, X., Chen, X., He, Y., Cheng, L., Huo, M., Yin, J., Hao, F., Chen, S., Wang, P., et al. (2021) · Materials Science and Engineering: R: Reports · doi:10.1016/j.mser.2020.100596 · Cited by 707
Heat treatment for metal additive manufacturing
Laleh, M., Sadeghi, E., Revilla, R. I., Chao, Q., Haghdadi, N., Hughes, A. E., Xu, W., De Graeve, I., Qian, M., Gibson, I., et al. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2022.101051 · Cited by 538
Metadata
- Authors
- Joseph, J., Jarvis, T., Wu, X., Stanford, N., Hodgson, P., & Fabijanic, D. M.
- Venue
- Materials Science and Engineering: A
- Publisher
- Elsevier BV
- Published
- 2015-05
- Volume
- 633
- Pages
- 184-193
- ISSN
- 0921-5093 (ISSN-L)
- OpenAlex
- W2015499745
- Cited by
- 343
- References
- 33
- FWCI
- 18.31
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.