Effect of heat treatment on the microstructure and mechanical properties of maraging steel by selective laser melting
The DOI matches its Crossref record; 25 of the 25 references it cites were found in a registry or an index.
Abstract
This work investigates the solution phenomenon, aging behavior and room-temperature mechanical properties of maraging steel manufactured by selective laser melting (SLM). Different heat treatment experiments, including solution treatment (ST), direct aging treatment (DAT) and solution + aging treatment (SAT) are designed. Microstructure analysis indicates that ST and SAT will eliminate the cellular and lath structures, but DAT has little effect on these. The content of austenite increases with the addition of DAT temperature and holding time. While austenite is almost undetectable in ST and SAT samples. Meanwhile, both the elongation and toughness of the samples with DAT gain a slight improvement with the temperature increasing. Importantly, DAT yields similar microhardness, tensile strength and impact toughness to SAT, although the resultant microstructures are completely different. The results demonstrate that DAT can achieve the similar mechanical properties to SAT samples. Samples with high mechanical properties (microhardness of 653.93 HV and ultimate strength of 2126.30 MPa) have been obtained by DAT at 520 °C for 6 h as well as solution treatment at 900 °C for 1 h and aging treatment at 520 °C for 6 h. This investigation reveals the evolution regularity of microstructure, microhardness, tensile performance and impact toughness of maraging steel manufactured by SLM after different heat treatments.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing of metallic components – Process, structure and properties
DebRoy, T., Wei, H. L., Zuback, J. S., Mukherjee, T., Elmer, J. W., Milewski, J. O., Beese, A. M., Wilson-Heid, A., De, A., & Zhang, W. (2018) · Progress in Materials Science · doi:10.1016/j.pmatsci.2017.10.001 · Cited by 8,805
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Additive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
Fundamentals of Solidification
Kurz, W., & Fisher, D. J. (2012) · ASM International eBooks · doi:10.31399/asm.tb.pdub.t53420429 · Cited by 3,292
Laser additive manufacturing of metallic components: materials, processes and mechanisms
Gu, D. D., Meiners, W., Wissenbach, K., & Poprawe, R. (2012) · International Materials Reviews · doi:10.1179/1743280411y.0000000014 · Cited by 3,197
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
Review of selective laser melting: Materials and applications
Yap, C. Y., Chua, C. K., Dong, Z. L., Liu, Z. H., Zhang, D. Q., Loh, L. E., & Sing, S. L. (2015) · Applied Physics Reviews · doi:10.1063/1.4935926 · Cited by 2,353
Vrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2012.07.022 · Cited by 1,896
Olakanmi, E. O., Cochrane, R. F., & Dalgarno, K. W. (2015) · Progress in Materials Science · doi:10.1016/j.pmatsci.2015.03.002 · Cited by 1,742
Selective laser melting of iron-based powder
Kruth, J. P., Froyen, L., Van Vaerenbergh, J., Mercelis, P., Rombouts, M., & Lauwers, B. (2004) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2003.11.051 · Cited by 1,550
Microstructure and mechanical properties of Selective Laser Melted 18Ni-300 steel
Kempen, K., Yasa, E., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2011) · Physics Procedia · doi:10.1016/j.phpro.2011.03.033 · Cited by 566
Tan, C., Zhou, K., Ma, W., Zhang, P., Liu, M., & Kuang, T. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.08.026 · Cited by 546
Sing, S. L., Yeong, W. Y., & Wiria, F. E. (2015) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2015.11.141 · Cited by 414
Casalino, G., Campanelli, S. L., Contuzzi, N., & Ludovico, A. D. (2015) · Optics & Laser Technology · doi:10.1016/j.optlastec.2014.07.021 · Cited by 412
Fundamentals of Selective Laser Melting of alloyed steel powders
Rombouts, M., Kruth, J. P., Froyen, L., & Mercelis, P. (2006) · CIRP Annals · doi:10.1016/s0007-8506(07)60395-3 · Cited by 400
Mutua, J., Nakata, S., Onda, T., & Chen, Z.-C. (2018) · Materials & Design · doi:10.1016/j.matdes.2017.11.042 · Cited by 315
Bai, Y., Yang, Y., Wang, D., & Zhang, M. (2017) · Materials Science and Engineering: A · doi:10.1016/j.msea.2017.06.033 · Cited by 310
Self-citationMetallic additive manufacturing: state-of-the-art review and prospects
Vayre, B., Vignat, F., & Villeneuve, F. (2012) · Mechanics & Industry · doi:10.1051/meca/2012003 · Cited by 294
On the Precipitation Hardening of Selective Laser Melted AlSi10Mg
Aboulkhair, N. T., Tuck, C., Ashcroft, I., Maskery, I., & Everitt, N. M. (2015) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-015-2980-7 · Cited by 286
Aging Behaviour and Mechanical Performance of 18-Ni 300 Steel Processed by Selective Laser Melting
Casati, R., Lemke, J., Tuissi, A., & Vedani, M. (2016) · Metals · doi:10.3390/met6090218 · Cited by 280
Yin, S., Chen, C., Yan, X., Feng, X., Jenkins, R., O'Reilly, P., Liu, M., Li, H., & Lupoi, R. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2018.06.005 · Cited by 226
Solid Freeform Fabrication Symposium Proceedings
Marcus, H. L., Beeman, J. J., Barlow, J. W., Bourell, D. L., & Crawford, R. (1993) · NASA STI/Recon Technical Report N · Cited by 140
Kang, N., Coddet, P., Dembinski, L., Liao, H., & Coddet, C. (2016) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2016.08.249 · Cited by 132
Microstructure and Mechanical Properties of Maraging Steel 300 After Selective Laser Melting
Yasa, E., Kempen, K., & Kruth, J. (2010) · Lirias · doi:10.26153/tsw/15205 · Cited by 90
Manufacturing of 18 Ni Marage 300 Steel Samples by Selective Laser Melting
Campanelli, S. L., Contuzzi, N., & Ludovico, A. D. (2009) · Advanced materials research · doi:10.4028/www.scientific.net/amr.83-86.850 · Cited by 43
Cited by
Abd-Elaziem, W., Elkatatny, S., Abd-Elaziem, A.-E., Khedr, M., Abd El-baky, M. A., Hassan, M. A., Abu-Okail, M., Mohammed, M., Järvenpää, A., Allam, T., et al. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.07.085 · Cited by 257
Mahmood, M. A., Chioibasu, D., Ur Rehman, A., Mihai, S., & Popescu, A. C. (2022) · Metals · doi:10.3390/met12010077 · Cited by 119
Metadata
- Authors
- Bai, Y., Wang, D., Yang, Y., & Wang, H.
- Venue
- Materials Science and Engineering: A
- Publisher
- Elsevier BV
- Published
- 2019-07
- Volume
- 760
- Pages
- 105-117
- ISSN
- 0921-5093 (ISSN-L)
- OpenAlex
- W2947461251
- Cited by
- 204
- References
- 25
- FWCI
- 11.44
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.