The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Effects of carbon nanotube on the thermal, mechanical, and electrical properties of PLA/CNT printed parts in the FDM process
Abstract
Abstract In this work, a filament based on polylactic acid (PLA)/ carbon nanotube (CNT) composites was prepared for the fused deposition modeling (FDM) process. The effects of the CNT content on the crystallization-melting behavior and melt flow rate (MFR) were tested to research the printability of the PLA/CNT. The results demonstrate that the CNT content has a significant influence on the mechanical properties and conductivity properties. The addition of 6 wt% CNT produced a 64.12% increase in tensile strength and a 29.29% increase in flexural strength. The electrical resistivity varied from approximately 1 × 1012 Ω/sq to 1 × 102 Ω/sq for CNT contents ranging from 0 wt% to 8 wt%. In addition, this paper assesses the effect of the filling velocity, liquefier temperature and layer thickness on the electrical resistivity. A lower filling velocity, higher liquefier temperature and greater layer thickness should be selected to achieve excellent electrical conductivity. These results demonstrate that PLA/CNT composites are a promising functionalizing material for FDM.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Photo-oxidative stabilization of carbon nanotubes on polylactic acid
Gorrasi, G., & Sorrentino, A. (2013) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2013.02.012 · Cited by 54
Cited by
Zaaba, N. F., & Jaafar, M. (2020) · Polymer Engineering & Science · doi:10.1002/pen.25511 · Cited by 683
Shanmugam, V., Das, O., Babu, K., Marimuthu, U., Veerasimman, A., Johnson, D. J., Neisiany, R. E., Hedenqvist, M. S., Ramakrishna, S., & Berto, F. (2021) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2020.106007 · Cited by 538
Fused deposition modeling: process, materials, parameters, properties, and applications
Rajan, K., Samykano, M., Kadirgama, K., Harun, W. S. W., & Rahman, M. M. (2022) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-08860-7 · Cited by 426
Current status and future directions of fused filament fabrication
Singh, S., Singh, G., Prakash, C., & Ramakrishna, S. (2020) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2020.04.049 · Cited by 385
Bikiaris, N. D., Koumentakou, I., Samiotaki, C., Meimaroglou, D., Varytimidou, D., Karatza, A., Kalantzis, Z., Roussou, M., Bikiaris, R. D., & Papageorgiou, G. Z. (2023) · Polymers · doi:10.3390/polym15051196 · Cited by 279
Metadata
- Authors
- Yang, L., Li, S., Zhou, X., Liu, J., Li, Y., Yang, M., Yuan, Q., & Zhang, W.
- Venue
- Synthetic Metals
- Publisher
- Elsevier BV
- Published
- 2019-07
- Volume
- 253
- Pages
- 122-130
- ISSN
- 0379-6779 (ISSN-L)
- OpenAlex
- W2945993027
- Cited by
- 179
- References
- 1
- FWCI
- 7.21
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effects of carbon nanotube on the thermal, mechanical, and electrical properties of PLA/CNT printed parts in the FDM process. https://app.cochat.ai/papers/10.1016/j.synthmet.2019.05.008
- The paper
- Yang, L., Li, S., Zhou, X., Liu, J., Li, Y., Yang, M., Yuan, Q., & Zhang, W. (2019). Effects of carbon nanotube on the thermal, mechanical, and electrical properties of PLA/CNT printed parts in the FDM process. Synthetic Metals. https://doi.org/10.1016/j.synthmet.2019.05.008
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.