The DOI matches its Crossref record.
Effects of energy density on morphology and properties of selective laser sintered polycarbonate
Open accessAbstract
Abstract Selective laser sintering (SLS) was used to prepare components from polycarbonate (PC) powder. The effects of energy density of the laser beam, ranging from 0.036 to 0.12 J mm −2 , on the physical density, tensile properties and morphology of the sintered specimens were investigated. At low energy density levels, the physical density and tensile strength of the specimens were found to increase with the increase in energy density. Smoke was observed when the components were sintered under an energy density above 0.09 J mm −2 , which suggests degradation of the PC powder. These specimens appeared slightly yellow and there was a reduction in the density and tensile strength. In specimens built under a low energy density, scanning electron microscopy (SEM) showed that slight fusion occurred at the surface of the PC particles. The individual particles could be identified and the voids between the particles were interconnected. The crack propagated between the particles during tensile fracture. When the energy density was high, the powder was fused thoroughly which allowed a more dense structure to be built. SEM also showed that fusion was more effective within the individual layers of the PC powder, whilst considerable amounts of voids were present between the layers. Therefore, the strength of the components normal to the layers is expected to be lower than the in-plane strength of the layers. Some wavy circular features were observed on the fracture surfaces of the specimens built under a high energy density. Such features are commonly found on the fracture surfaces of brittle plastics. The work forms a basis for the production of selective laser sintered PC functional products.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
3D printing of ceramics: A review
Chen, Z., Li, Z., Li, J., Liu, C., Lao, C., Fu, Y., Liu, C., Li, Y., Wang, P., & He, Y. (2019) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2018.11.013 · Cited by 2,109
Laser sintering of polyamides and other polymers
Goodridge, R. D., Tuck, C. J., & Hague, R. J. M. (2012) · Progress in Materials Science · doi:10.1016/j.pmatsci.2011.04.001 · Cited by 835
Dependence of mechanical properties of polyamide components on build parameters in the SLS process
Caulfield, B., McHugh, P. E., & Lohfeld, S. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2006.09.007 · Cited by 598
Polymeric composites for powder-based additive manufacturing: Materials and applications
Yuan, S., Shen, F., Chua, C. K., & Zhou, K. (2019) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2018.11.001 · Cited by 525
Lasers in additive manufacturing: A review
Lee, H., Lim, C. H. J., Low, M. J., Tham, N., Murukeshan, V. M., & Kim, Y.-J. (2017) · International Journal of Precision Engineering and Manufacturing-Green Technology · doi:10.1007/s40684-017-0037-7 · Cited by 449
Metadata
- Authors
- Ho, H. C. H., Gibson, I., & Cheung, W. L.
- Venue
- Journal of Materials Processing Technology
- Publisher
- Elsevier BV
- Published
- 1999-05
- Volume
- 89-90
- Pages
- 204-210
- ISSN
- 0924-0136 (ISSN-L)
- OpenAlex
- W1976102398
- Cited by
- 167
- References
- 0
- FWCI
- 1.09
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Effects of energy density on morphology and properties of selective laser sintered polycarbonate. https://app.cochat.ai/papers/10.1016/s0924-0136(99)00007-2
- The paper
- Ho, H. C. H., Gibson, I., & Cheung, W. L. (1999). Effects of energy density on morphology and properties of selective laser sintered polycarbonate. Journal of Materials Processing Technology. https://doi.org/10.1016/s0924-0136(99)00007-2
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.