The DOI matches its Crossref record; 28 of the 28 references it cites were found in a registry or an index.
High thermoelectric performance of oxyselenides: intrinsically low thermal conductivity of Ca-doped BiCuSeO
Open accessAbstract
We report on the high thermoelectric performance of p-type polycrystalline BiCuSeO, a layered oxyselenide composed of alternating conductive (Cu2Se2)2− and insulating (Bi2O2)2+ layers. The electrical transport properties of BiCuSeO materials can be significantly improved by substituting Bi3+ with Ca2+. The resulting materials exhibit a large positive Seebeck coefficient of ∼+330 μV K−1 at 300 K, which may be due to the ‘natural superlattice’ layered structure and the moderate effective mass suggested by both electronic density of states and carrier concentration calculations. After doping with Ca, enhanced electrical conductivity coupled with a moderate Seebeck coefficient leads to a power factor of ∼4.74 μW cm−1 K−2 at 923 K. Moreover, BiCuSeO shows very low thermal conductivity in the temperature range of 300 (∼0.9 W m−1 K−1) to 923 K (∼0.45 W m−1 K−1). Such low thermal conductivity values are most likely a result of the weak chemical bonds (Young’s modulus, E∼76.5 GPa) and the strong anharmonicity of the bonding arrangement (Gruneisen parameter, γ∼1.5). In addition to increasing the power factor, Ca doping reduces the thermal conductivity of the lattice, as confirmed by both experimental results and Callaway model calculations. The combination of optimized power factor and intrinsically low thermal conductivity results in a high ZT of ∼0.9 at 923 K for Bi0.925Ca0.075CuSeO. Li-Dong Zhao, Jiaqing He and co-workers have gained insight into the highly thermoelectric properties of a bismuth–copper oxyselenide (BiCuSeO), a polycrystalline, layered compound. BiCuSeO's ability to produce a significant electric potential from a temperature difference, and vice versa, arises from its intrinsically low thermal conductivity, and can be further improved by boosting the material's electrical conductivity through doping with strontium or barium, or introducing copper deficiencies. The researchers have now carried out an extensive characterization of the oxyselenide and propose that its conveniently low thermal conductivity results from the weak chemical bonds that exist between two different kinds of layers, and a particular bonding arrangement, in the material's lattice. Moreover, by substituting bismuth ions (Bi3+) with calcium ions (Ca3+) the thermal conductivity of the lattice could be lowered further, leading to an improvement in the oxyselenide's thermoelectric properties. We report on the promising thermoelectric performance of p-type polycrystalline BiCuSeO, which is a layered oxyselenide composed of conductive (Cu2Se2)2− layers that alternate with insulating (Bi2O2)2+ layers. Electrical transport properties can be optimized by substituting Bi3+ with Ca2+. Moreover, BiCuSeO shows very low thermal conductivity in the temperature ranges of 300 (∼0.9 W m−1K−1) to 923 K (∼0.45 W m−1 K−1). These intrinsically low thermal conductivity values may result from the weak chemical bonds of the material as well as the strong anharmonicity of the bonding arrangement. The combination of the optimized power factor and the intrinsically low thermal conductivity results in a high ZT of ∼0.9 at 923 K for Bi0.925Ca0.075CuSeO.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Special points for Brillouin-zone integrations
Monkhorst, H. J., & Pack, J. D. (1976) · Physical Review B · doi:10.1103/physrevb.13.5188 · Cited by 71,721
First principles methods using CASTEP
Clark, S. J., Segall, M. D., Pickard, C. J., Hasnip, P. J., Probert, M. I. J., Refson, K., & Payne, M. C. (2005) · Zeitschrift für Kristallographie - Crystalline Materials · doi:10.1524/zkri.220.5.567.65075 · Cited by 14,633
Iron-Based Layered Superconductor La[O1-xFx]FeAs (x = 0.05−0.12) with Tc = 26 K
Kamihara, Y., Watanabe, T., Hirano, M., & Hosono, H. (2008) · Journal of the American Chemical Society · doi:10.1021/ja800073m · Cited by 7,868
High-Thermoelectric Performance of Nanostructured Bismuth Antimony Telluride Bulk Alloys
Poudel, B., Hao, Q., Ma, Y., Lan, Y., Minnich, A., Yu, B., Yan, X., Wang, D., Muto, A., Vashaee, D., et al. (2008) · Science · doi:10.1126/science.1156446 · Cited by 5,606
Thin-film thermoelectric devices with high room-temperature figures of merit
Venkatasubramanian, R., Siivola, E., Colpitts, T., & O'Quinn, B. (2001) · Nature · doi:10.1038/35098012 · Cited by 5,205
Enhancement of Thermoelectric Efficiency in PbTe by Distortion of the Electronic Density of States
Heremans, J. P., Jovovic, V., Toberer, E. S., Saramat, A., Kurosaki, K., Charoenphakdee, A., Yamanaka, S., & Snyder, G. J. (2008) · Science · doi:10.1126/science.1159725 · Cited by 4,161
Cubic AgPb m SbTe 2+ m : Bulk Thermoelectric Materials with High Figure of Merit
Hsu, K. F., Loo, S., Guo, F., Chen, W., Dyck, J. S., Uher, C., Hogan, T., Polychroniadis, E. K., & Kanatzidis, M. G. (2004) · Science · doi:10.1126/science.1092963 · Cited by 2,927
Quantum Dot Superlattice Thermoelectric Materials and Devices
Harman, T. C., Taylor, P. J., Walsh, M. P., & LaForge, B. E. (2002) · Science · doi:10.1126/science.1072886 · Cited by 2,495
Iron-Based Layered Superconductor: LaOFeP
Kamihara, Y., Hiramatsu, H., Hirano, M., Kawamura, R., Yanagi, H., Kamiya, T., & Hosono, H. (2006) · Journal of the American Chemical Society · doi:10.1021/ja063355c · Cited by 1,537
Materials selection guidelines for low thermal conductivity thermal barrier coatings
Clarke, D. R. (2003) · Surface and Coatings Technology · doi:10.1016/s0257-8972(02)00593-5 · Cited by 1,496
Effect of Point Imperfections on Lattice Thermal Conductivity
Callaway, J., & von Baeyer, H. C. (1960) · Physical Review · doi:10.1103/physrev.120.1149 · Cited by 1,168
Nanostructured Thermoelectrics: The New Paradigm?
Kanatzidis, M. G. (2010) · Chemistry of Materials · doi:10.1021/cm902195j · Cited by 1,153
Intrinsically Minimal Thermal Conductivity in CubicI−V−VI2Semiconductors
Morelli, D. T., Jovovic, V., & Heremans, J. P. (2008) · Physical Review Letters · doi:10.1103/physrevlett.101.035901 · Cited by 982
High-performance nanostructured thermoelectric materials
Li, J.-F., Liu, W.-S., Zhao, L.-D., & Zhou, M. (2010) · NPG Asia Materials · doi:10.1038/asiamat.2010.138 · Cited by 963
Self-citationSemiconducting Lead Chalcogenides
Ravich, Y. I., Efimova, B. A., & Smirnov, I. A. (1970) · Springer eBooks · doi:10.1007/978-1-4684-8607-0 · Cited by 904
CsBi 4 Te 6 : A High-Performance Thermoelectric Material for Low-Temperature Applications
Chung, D.-Y., Hogan, T., Brazis, P., Rocci-Lane, M., Kannewurf, C., Bastea, M., Uher, C., & Kanatzidis, M. G. (2000) · Science · doi:10.1126/science.287.5455.1024 · Cited by 900
High Thermal Conductivity Materials
(2006) · Springer eBooks · doi:10.1007/b106785 · Cited by 465
Bi 1 − x Sr x CuSeO oxyselenides as promising thermoelectric materials
Zhao, L., Bérardan, D., Pei, Y. L., Byl, C., Pinsard, L., & Dragoe, N. (2010) · Applied Physics Letters · doi:10.1063/1.3485050 · Cited by 422
Self-citationEntropically Stabilized Local Dipole Formation in Lead Chalcogenides
Božin, E. S., Malliakas, C. D., Souvatzis, P., Proffen, T., Spaldin, N. A., Kanatzidis, M. G., & Billinge, S. J. L. (2010) · Science · doi:10.1126/science.1192759 · Cited by 374
Thermoelectric Ceramics for Energy Harvesting
Koumoto, K., Funahashi, R., Guilmeau, E., Miyazaki, Y., Weidenkaff, A., Wang, Y., & Wan, C. (2013) · Journal of the American Ceramic Society · doi:10.1111/jace.12076 · Cited by 356
Influence of porosity on Young's modulus and Poisson's ratio in alumina ceramics
Asmani, M., Kermel, C., Leriche, A., & Ourak, M. (2001) · Journal of the European Ceramic Society · doi:10.1016/s0955-2219(00)00314-9 · Cited by 306
Hiramatsu, H., Yanagi, H., Kamiya, T., Ueda, K., Hirano, M., & Hosono, H. (2008) · Chemistry of Materials · doi:10.1021/cm702303r · Cited by 295
Thermal Conductivity of Complex Dielectric Crystals
Roufosse, M., & Klemens, P. G. (1973) · Physical Review B · doi:10.1103/physrevb.7.5379 · Cited by 291
Experimental determinations of the Lorenz number
Kumar, G. S., Prasad, G., & Pohl, R. O. (1993) · Journal of Materials Science · doi:10.1007/bf01154931 · Cited by 245
Relation between the parameters of the elasticity theory and averaged bulk modulus of solids
Sanditov, D. S., & Belomestnykh, V. N. (2011) · Technical Physics · doi:10.1134/s106378421111020x · Cited by 188
Effect of mixed grain sizes on thermoelectric performance of Bi2Te3 compound
Zhao, L.-D., Zhang, B.-P., Liu, W.-S., & Li, J.-F. (2009) · Journal of Applied Physics · doi:10.1063/1.3063694 · Cited by 168
Self-citationSkoug, E. J., Cain, J. D., & Morelli, D. T. (2010) · Applied Physics Letters · doi:10.1063/1.3425886 · Cited by 133
Ultralow Thermal Conductivity in Highly Anion-Defective Aluminates
Wan, C., Qu, Z., He, Y., Luan, D., & Pan, W. (2008) · Physical Review Letters · doi:10.1103/physrevlett.101.085901 · Cited by 121
Self-citation
Cited by
Advanced Thermoelectric Design: From Materials and Structures to Devices
Shi, X.-L., Zou, J., & Chen, Z.-G. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.0c00026 · Cited by 2,524
Rationally Designing High-Performance Bulk Thermoelectric Materials
Tan, G., Zhao, L.-D., & Kanatzidis, M. G. (2016) · Chemical Reviews · doi:10.1021/acs.chemrev.6b00255 · Cited by 2,355
Self-citationThe panoscopic approach to high performance thermoelectrics
Zhao, L.-D., Dravid, V. P., & Kanatzidis, M. G. (2014) · Energy Environ. Sci. · doi:10.1039/c3ee43099e · Cited by 997
Self-citationRecent development and application of thermoelectric generator and cooler
He, W., Zhang, G., Zhang, X., Ji, J., Li, G., & Zhao, X. (2015) · Applied Energy · doi:10.1016/j.apenergy.2014.12.075 · Cited by 816
BiCuSeO oxyselenides: new promising thermoelectric materials
Zhao, L.-D., He, J., Berardan, D., Lin, Y., Li, J.-F., Nan, C.-W., & Dragoe, N. (2014) · Energy Environ. Sci. · doi:10.1039/c4ee00997e · Cited by 722
Self-citation
Metadata
- Authors
- Pei, Y.-L., He, J., Li, J.-F., Li, F., Liu, Q., Pan, W., Barreteau, C., Berardan, D., Dragoe, N., & Zhao, L.-D.
- Venue
- NPG Asia Materials
- Published
- 2013-05
- Volume
- 5
- Issue
- 5
- Pages
- e47-e47
- ISSN
- 1884-4049 (ISSN-L)
- 1884-4057
- OpenAlex
- W2038175832
- Cited by
- 431
- References
- 28
- FWCI
- 14.06
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.