CoChat

A universal standardized method for output capability assessment of nanogenerators

Open access
Xia, Xin, Fu, Jingjing, Zi, Yunlong · 2019 · Nature Communications

The DOI matches its Crossref record; 42 of the 42 references it cites were found in a registry or an index.

Abstract

To quantitatively evaluate the output performance of triboelectric nanogenerators, figures of merit have been developed. However, the current figures of merit, without considering the breakdown effect that seriously affects the effective maximized energy output, are limited for application. Meanwhile, a method to evaluate output capability of nanogenerators is needed. Here, a standardized method that considers the breakdown effect is proposed for output capability assessment of nanogenerators. Contact separation and contact freestanding-triboelectric-layer modes triboelectric nanogenerators are used to demonstrate this method, and the effective maximized energy output and revised figures of merit are calculated based on the experimental results. These results are consistent with those theoretically calculated based on Paschen’s law. This method is also conducted to evaluate a film-based piezoelectric nanogenerator, demonstrating its universal applicability for nanogenerators. This study proposes a standardized method for evaluating the effective output capability of nanogenerators, which is crucial for standardized evaluation and application of nanogenerator technologies.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1038/s41467-019-12465-2

Cites

42 of 42 references verified0 citation errors · 0 not checkable

Statistics

Figures

Fig. 1 Introduction of the method. a Energy flow chart of TENG system. b The V–Q plot at σ = 50 μC m−2, showing the positive (“+”) part as the non-breakdown area and negative (“−”) part as the breakdown area. c Circuit of the universal method, with TENG2 being the power source and TENG1 being the target device. d Process flow chart of the universal method
Fig. 1 Introduction of the method. a Energy flow chart of TENG system. b The V–Q plot at σ = 50 μC m−2, showing the positive (“+”) part as the non-breakdown area and negative (“−”) part as the breakdown area. c Circuit of the universal method, with TENG2 being the power source and TENG1 being the target device. d Process flow chart of the universal methodCC BY · PubMed Central
Fig. 2 Output characteristics of breakdown. Q–V plots of CS mode TENG for a no breakdown; b breakdown with spark; c breakdown without spark. Inset plots with lines in blue in a–c are the transfer charge results. Target points by green arrows in b and c are breakdown points. The inset picture of b is the photo of a visible spark at x = 2 mm. Source data are provided as a Source Data file
Fig. 2 Output characteristics of breakdown. Q–V plots of CS mode TENG for a no breakdown; b breakdown with spark; c breakdown without spark. Inset plots with lines in blue in a–c are the transfer charge results. Target points by green arrows in b and c are breakdown points. The inset picture of b is the photo of a visible spark at x = 2 mm. Source data are provided as a Source Data fileCC BY · PubMed Central
Fig. 3 Breakdown results for a contact-separation triboelectric nanogenerator. a Schematic diagram of CS mode TENG. b Average breakdown voltage V1 from experiment, compared with theoretical values calculated by Paschen’s law. c Average capacitance C, compared with theoretical values calculated by the equation considering two-side edge effects. d Cycle for maximized energy output with the threshold breakdown curve, compared with theoretical curve by Paschen’s law. QSC,max = 67nC. Source data are provided as a Source Data file
Fig. 3 Breakdown results for a contact-separation triboelectric nanogenerator. a Schematic diagram of CS mode TENG. b Average breakdown voltage V1 from experiment, compared with theoretical values calculated by Paschen’s law. c Average capacitance C, compared with theoretical values calculated by the equation considering two-side edge effects. d Cycle for maximized energy output with the threshold breakdown curve, compared with theoretical curve by Paschen’s law. QSC,max = 67nC. Source data are provided as a Source Data fileCC BY · PubMed Central
Fig. 4 Breakdown for contact freestanding-triboelectric-layer nanogenerator. a Schematic diagram of CFT mode TENG. Average breakdown voltage b V1 and c V3 from experiment, compared with theoretical values calculated by Paschen’s law. Figure of visible spark insets in b. d Average capacitance Ctotal, compared with theoretical values calculated by the equation considering two-side edge effects. e Cycle for maximized energy output with the threshold breakdown curve compared with theoretical curve by Paschen’s law. QSC,max = 25 nC. Source data are provided as a Source Data file
Fig. 4 Breakdown for contact freestanding-triboelectric-layer nanogenerator. a Schematic diagram of CFT mode TENG. Average breakdown voltage b V1 and c V3 from experiment, compared with theoretical values calculated by Paschen’s law. Figure of visible spark insets in b. d Average capacitance Ctotal, compared with theoretical values calculated by the equation considering two-side edge effects. e Cycle for maximized energy output with the threshold breakdown curve compared with theoretical curve by Paschen’s law. QSC,max = 25 nC. Source data are provided as a Source Data fileCC BY · PubMed Central
Fig. 5 Further applications of the proposed method. Q–V plots of a PVDF-film-based PENG without cutting, no breakdown happens; and b PVDF piezo-film after cutting, with blue lines of transfer charge and figures of experiment devices inset. Points targeted by green arrow in b is breakdown point. c Cycle for maximized energy with the threshold breakdown curves of PVDF film after cutting with schematic diagram and figure with visible spark inset in. The measured structural FOM (d); material FOM (e) and performance FOM (f) of different structures. Source data are provided as a Source Data file
Fig. 5 Further applications of the proposed method. Q–V plots of a PVDF-film-based PENG without cutting, no breakdown happens; and b PVDF piezo-film after cutting, with blue lines of transfer charge and figures of experiment devices inset. Points targeted by green arrow in b is breakdown point. c Cycle for maximized energy with the threshold breakdown curves of PVDF film after cutting with schematic diagram and figure with visible spark inset in. The measured structural FOM (d); material FOM (e) and performance FOM (f) of different structures. Source data are provided as a Source Data fileCC BY · PubMed Central

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 42 references

Research works printed but not linked: 1

  1. Lieberman, M. A. & Lichtenberg, A. J. Principles of Plasma Discharges and Materials Processing, 2nd edn. (John Wiley & Sons 2008).

Cited by

See all 130

Metadata

Authors
Xia, X., Fu, J., & Zi, Y.
Affiliations
Chinese University of Hong Kong (HK)
Corresponding author
Zi, Yunlong
Venue
Nature Communications
Published
2019-09-27
Volume
10
Issue
1
Pages
4428-4428
ISSN
2041-1723 (ISSN-L)
OpenAlex
W2976452716
Cited by
125
References
42
Citations by year
2026: 13 · 2025: 19 · 2024: 12 · 2023: 22 · 2022: 19 · 2021: 21 · 2020: 17 · 2019: 2
FWCI
5.20
Type
journal article
Language
en
Open access
Licence
Locations
  • Nature Communications (publishedVersion, cc-by)
  • Europe PMC (PubMed Central) (publishedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • RePEc: Research Papers in Economics (submittedVersion)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
  • Rare & Special e-Zone (The Hong Kong University of Science and Technology) (submittedVersion)
Funders
  • Innovation and Technology Fund (ITS/085/18)
  • CUHK | Shun Hing Institute of Advanced Engineering (RNE-p5-18)
  • Chinese University of Hong Kong (4055086)
Topics
  • Physical Sciences › Engineering › Biomedical Engineering › Advanced Sensor and Energy Harvesting Materials
  • Physical Sciences › Engineering › Mechanical Engineering › Innovative Energy Harvesting Technologies
  • Physical Sciences › Physics and Astronomy › Atomic and Molecular Physics, and Optics › Force Microscopy Techniques and Applications
Keywords
triboelectric nanogenerator, figure of merit, Paschen's law, contact separation, piezoelectric nanogenerators, energy output

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: A universal standardized method for output capability assessment of nanogenerators. https://app.cochat.ai/papers/10.1038/s41467-019-12465-2
The paper
Xia, X., Fu, J., & Zi, Y. (2019). A universal standardized method for output capability assessment of nanogenerators. Nature Communications. https://doi.org/10.1038/s41467-019-12465-2

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.