The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Three-Dimensional Printed Electrode and Its Novel Applications in Electronic Devices
Open accessAbstract
Three-dimensional (3D) printing technology provides a novel approach to material fabrication for various applications because of its ability to create low-cost 3D printed platforms. In this study, a printable graphene-based conductive filament was employed to create a range of 3D printed electrodes (3DEs) using a commercial 3D printer. This printing technology provides a simplistic and low-cost approach, which eliminates the need for the ex-situ modification and post-treatment of the product. The conductive nature of the 3DEs provides numerous deposition platforms for electrochemical active nanomaterials such as graphene, polypyrrole, and cadmium sulfide, either through electrochemical or physical approaches. To provide proof-of-concept, these 3DEs were physiochemically and electrochemically evaluated and proficiently fabricated into a supercapacitor and photoelectrochemical sensor. The as-fabricated supercapacitor provided a good capacitance performance, with a specific capacitance of 98.37 Fg−1. In addition, these 3DEs were fabricated into a photoelectrochemical sensing platform. They had a photocurrent response that exceeded expectations (~724.1 μA) and a lower detection limit (0.05 μM) than an ITO/FTO glass electrode. By subsequently modifying the printing material and electrode architecture, this 3D printing approach could provide a facile and rapid manufacturing process for energy devices based on the conceptual design.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
3D printed microfluidic devices: enablers and barriers
Waheed, S., Cabot, J. M., Macdonald, N. P., Lewis, T., Guijt, R. M., Paull, B., & Breadmore, M. C. (2016) · Lab on a Chip · doi:10.1039/c6lc00284f · Cited by 1,039
Cited by
An Overview on 3D Printing Technology: Technological, Materials, and Applications
Shahrubudin, N., Lee, T. C., & Ramlan, R. (2019) · Procedia Manufacturing · doi:10.1016/j.promfg.2019.06.089 · Cited by 2,050
Electrochemical biosensors for pathogen detection
Cesewski, E., & Johnson, B. N. (2020) · Biosensors and Bioelectronics · doi:10.1016/j.bios.2020.112214 · Cited by 902
A critical review on the fused deposition modeling of thermoplastic polymer composites
Penumakala, P. K., Santo, J., & Thomas, A. (2020) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2020.108336 · Cited by 704
3D Printing for Electrochemical Energy Applications
Browne, M. P., Redondo, E., & Pumera, M. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.9b00783 · Cited by 434
Complete Additively Manufactured (3D-Printed) Electrochemical Sensing Platform
Richter, E. M., Rocha, D. P., Cardoso, R. M., Keefe, E. M., Foster, C. W., Munoz, R. A. A., & Banks, C. E. (2019) · Analytical Chemistry · doi:10.1021/acs.analchem.9b02573 · Cited by 338
Metadata
- Authors
- Foo, C. Y., Lim, H. N., Mahdi, M. A., Wahid, M. H., & Huang, N. M.
- Venue
- Scientific Reports
- Published
- 2018-05-09
- Volume
- 8
- Issue
- 1
- Pages
- 7399-7399
- ISSN
- 2045-2322 (ISSN-L)
- OpenAlex
- W2805163993
- Cited by
- 213
- References
- 1
- FWCI
- 7.22
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Three-Dimensional Printed Electrode and Its Novel Applications in Electronic Devices. https://app.cochat.ai/papers/10.1038/s41598-018-25861-3
- The paper
- Foo, C. Y., Lim, H. N., Mahdi, M. A., Wahid, M. H., & Huang, N. M. (2018). Three-Dimensional Printed Electrode and Its Novel Applications in Electronic Devices. Scientific Reports. https://doi.org/10.1038/s41598-018-25861-3
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.