Multiple quadrants displacement tracking control of independent metering electro-hydraulic system
Open accessThe DOI matches its Crossref record; 30 of the 30 references it cites were found in a registry or an index; 1 of the 24 sources its claims cite were checked for support.
Abstract
Aiming at the oscillation caused by the hydraulic cylinder of independent metering system (IMS) running between multiple working quadrants, a novel multiple quadrants switching displacement tracking control strategy is proposed in this paper. In this control strategy, both the cylinder chamber pressure under resistance and overrunning conditions are controlled by the inlet valve, and the outlet valve is utilized to control the displacement of cylinder. This method allows the hydraulic cylinder to always run in energy-efficient. When the working quadrant changes, the valve's working modes are unchanged, which avoids oscillation caused by changes of valves working modes in principle. And a reduced-order active disturbance rejective displacement controller and an active disturbance rejective pressure controller are designed to get high-precision tracking of the displacement and pressure. Numerous experimental results show that the proposed method is reasonable and effective, hydraulic cylinder operates smoothly between multiple quadrants, the pressure and displacement controllers have good anti-interference ability and robustness, and the energy consumption can be reduced by more than 23% compared to the traditional constant pressure valve control system.
Overview
CoChat Summary
## TL;DR
The paper proposes a multiple-quadrants displacement tracking control strategy for an independent metering electro-hydraulic system (IMS) that keeps valve operating modes unchanged while switching smoothly between resistance and overrunning conditions. Experiments on a test bench report stable displacement/pressure control and lower energy use than traditional constant-pressure valve control.
## Key findings
- The proposed method controls the return-chamber pressure in resistance conditions and the inlet-chamber pressure in overrunning conditions using the inlet valve, while displacement is controlled by the outlet valve in both cases, allowing smooth quadrant switching without changing valve working modes.
- In the RETOE experiment, displacement tracking error was maintained at about 3.5 mm, and in the OETRE experiment it was about 4.5 mm; the paper states the error did not oscillate after quadrant changes.
- Compared with traditional constant pressure valve control (TCPVC), the proposed strategy reduced energy consumption from 11.92 kJ to 9.18 kJ in RETOE, a reduction of 2.74 kJ or 23%.
- In OETRE, the proposed strategy used 8.4 kJ versus 13.1 kJ for TCPVC, reported as a 35.9% reduction; at system pressures of 90 bar, 100 bar, and 110 bar, energy consumption was reduced by 26.0%, 26.5%, and 27.8%, respectively, and the paper states energy saving was more than 40% at different pressures overall.
## Methods
- The paper proposes a control strategy based on active disturbance rejection control (ADRC), with a reduced-order ADRC displacement controller and an ADRC pressure controller.
- The study uses an IMS hydraulic test bench with a hydraulic cylinder, two proportional servo valves, a pump, a motor, load cylinder, reducing valves, transducers, and dSPACE control hardware; the sampling frequency is 1000 Hz.
- Experimental verification includes quadrant-switching tests for resistance extension to overrunning extension (RETOE) and overrunning extension to resistance extension (OETRE), plus comparisons against traditional constant pressure valve control (TCPVC) and tests at different maximum system pressures.
## Limitations
- The paper states that the process is verified by experiments on a test bench, and that future work will study more variable working conditions, apply the method to actual construction machinery, and compare it with existing control methods.
- Evident from the text: the validation is limited to the reported bench experiments and the specific tested quadrants/pressure settings; the paper does not report field trials in real machinery.
- Evident from the text: the controller design relies on simplified models and on measuring chamber pressures; the paper notes the hydraulic system is nonlinear and an accurate mathematical model cannot be established.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures




























Verification
Claims the paper makes
1 Valid · 2 Not valid · 10 Not checked · 96 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“However, in practice, the magnitude and direction of the load force on the equipment vary with the working conditions 16 – 18 .”
What the sources say
- Not checked yetcites [16] Helian, B., Chen, Z. & Yao, B. Energy-saving and accurate motion control of a hydraulic actuator with uncertain negative loads. Chin. J. Aeronaut. 34(5), 253–264 (2021). source
- Not checked yetcites [17] Jin, M. & Wang, Q. Efficient pump and meter-out control for electrohydraulic system with time-varying negative load. Proc. IMechE Part I J. Syst. Control Eng. 232(9), 1170–1181 (2018).
- Partly supportedcites [18] Li, J., Li, W. & Du, X. Research on the characteristics of electro-hydraulic position servo system of RBF neural network under fuzzy rules. Sci. Rep. 14, 15332 (2024). sourceExperimental — accuracy not yet measured
The Introduction (p. 1) states that 'EHSS is subject to external load disturbance during operation, and it is often difficult to ensure control accuracy under disturbance conditions', and the controller-design section notes the PID learning rate cannot correct itself 'according to the amplitude of the disturbance suffered', so load disturbance of varying magnitude during operation is supported. The paper also ties changes in working conditions to system parameters, not to the load force: 'when the work requirements and conditions change, some system parameters will change'. Nothing in our copy states that the DIRECTION of the load force varies with working conditions, and its simulations apply fixed-magnitude load disturbances and stepped load stiffness values rather than characterising load-force variation in practice. (LLM, conf=0.68)
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“It is calculated that the system consumes 9.18 kJ to complete the extension process.”
plainSingle case- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“is larger as the force increases.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“To verify the feasibility of the proposed method, a serious of experiments are done and the results illustrate that the control method can achieve smooth switching of the cylinder between multiple quadrants.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The pressure control curve is the same as the expected result of the theoretical pressure control strategy.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
43 more claims
Create a free account to see all 109 claims and to verify the 23 references still open.
- It may state two separate claims as one. 53
- Probably not a substantial claim. 18
- The quote only partly states this claim. 4
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“\begin{document}$$\left\{\begin{array}{c}{\dot{\widehat{z}}}_{1}={\widehat{z}}_{2}+2{\omega }_{od}\left({\widehat{z}}_{1}-{z}_{1}\right)+{b}_{d}{u}_{2}\\ {\dot{\widehat{z}}}_{2}=-{\omega }_{od}^{2}\left({\widehat{z}}_{1}-{z}_{1}\right)\end{array}\right.$$\end{document}”
“the accuracy of the observer can be improved by increasing the value of”
Citations
Cites
From PID to Active Disturbance Rejection Control
Han, J. (2009) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2008.2011621 · Cited by 6,803
Chen, Z., Huang, F., Yang, C., & Yao, B. (2020) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2019.2898587 · Cited by 225
Research and Development of Electro-hydraulic Control Valves Oriented to Industry 4.0: A Review
Xu, B., Shen, J., Liu, S., Su, Q., & Zhang, J. (2020) · Chinese Journal of Mechanical Engineering · doi:10.1186/s10033-020-00446-2 · Cited by 193 · cited 1×
“As hydraulic systems are characterized by large output force and strong environmental adaptability, they are still the main transmission system of heavy industry, construction machinery etc. 1–4 .”
BackgroundLyu, L., Chen, Z., & Yao, B. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2875666 · Cited by 113
Coordinate Control of Energy Saving Programmable Valves
Liu, S., & Yao, B. (2008) · IEEE Transactions on Control Systems Technology · doi:10.1109/tcst.2007.903073 · Cited by 113
A Survey of Powertrain Technologies for Energy-Efficient Heavy-Duty Machinery
Quan, Z., Ge, L., Wei, Z., Li, Y., & Quan, L. (2021) · Proceedings of the IEEE · doi:10.1109/jproc.2021.3051555 · Cited by 94
Trends in hydraulic actuators and components in legged and tough robots: a review
Suzumori, K., & Faudzi, A. A. M. (2018) · Advanced Robotics · doi:10.1080/01691864.2018.1455606 · Cited by 91
Pump/valves coordinate control of the independent metering system for mobile machinery
Bing Hong, X. U., Ding, R., Zhang, J., Cheng, M., & Sun, T. (2015) · Automation in Construction · doi:10.1016/j.autcon.2015.04.012 · Cited by 90
Review of boom potential energy regeneration technology for hydraulic construction machinery
Lin, T., Chen, Q., Ren, H., Huang, W., Chen, Q., & Fu, S. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.05.131 · Cited by 89
He, X., Xiao, G., Hu, B., Tan, L., Tang, H., He, S., & He, Z. (2019) · Energy Conversion and Management · doi:10.1016/j.enconman.2019.112413 · Cited by 88
Research works printed but not linked: 4
- Jin, M. & Wang, Q. Efficient pump and meter-out control for electrohydraulic system with time-varying negative load. Proc. IMechE Part I J. Syst. Control Eng. 232(9), 1170–1181 (2018).
- Chen, G., Wang, J., Wang, S. & Ma, L. Separate meter in and separate meter out energy saving control system using dual servo valves under complex load conditions. Trans. Beijing Inst. Technol. 36(10), 1053–1058 (2016).
- Chen, Z. et al. Motion control of independent metering electro-hydraulic system based on chamber pressure planning without mode switch. J. Mech. Eng. 60(02), 302–312 (2024).
- Gao, Z. Scaling and bandwidth-parameterization based controller tuning. In Proceedings of the 2003 American Control Conference, Denver, CO, USA 4989–4996 (2003).
Cited by
Weiwei, L., Yong, H. H., & Chuiyi, L. (2026) · Scientific Reports · doi:10.1038/s41598-025-33521-6 · Cited by 4
A Seamless Mode Switching Control Method for Independent Metering Controlled Hydraulic Actuator
Liu, Y., Li, J., & Cong, D. (2026) · Technologies · doi:10.3390/technologies14010063
“Meng [26] introduced a fixed-valve working mode in which the inlet valve handles pressure control and the outlet valve handles displacement control, eliminating the need for valve function reassignment during load changes.”
Wang, T., Zhu, X., Shao, F., He, X., & Zhu, Y. (2026) · Processes · doi:10.3390/pr14132163
Metadata
- Authors
- Meng, W., Lutang, L., Aihong, W., Hong, R., & Youshan, G.
- Affiliations
- Taiyuan University of Science and Technology (CN)
- ORCID
- Meng, Wang
- Venue
- Scientific Reports
- Published
- 2024-09-20
- Volume
- 14
- Issue
- 1
- Pages
- 21951-21951
- ISSN
- 2045-2322 (ISSN-L)
- PMC
- PMC11415359
- OpenAlex
- W4402713457
- Cited by
- 3
- References
- 30
- Citations by year
- 2026: 3
- FWCI
- 0.40
- Type
- journal article
- Language
- en
- Open access
- gold
- dx.doi.org
- Licence
- cc-by-nc-nd
- creativecommons.org/licenses/by-nc-nd/4.0 (tdm)
- creativecommons.org/licenses/by-nc-nd/4.0 (vor)
- Locations
- Scientific Reports (publishedVersion, cc-by-nc-nd)
- PubMed Central (publishedVersion, cc-by-nc-nd)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Dr. scientific research Startup Project of Taiyuan University of Science and Technology (20202030)
- Shanxi Center of Technology Innovation for Electrohydraulic Control and Health Management of Heavy Machinery
- TAIYUAN UNIVERSITY OF SCIENCE AND TECHNOLOGY SCIENTIFIC RESEARCH INITIAL FUNDING (20242038)
- Fund Program for the Scientific Activities of Selected Returned 0verseas Professionals in Shanxi Province (20240021)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Hydraulic and Pneumatic Systems
- Physical Sciences › Engineering › Control and Systems Engineering › Adaptive Control of Nonlinear Systems
- Physical Sciences › Engineering › Mechanical Engineering › Control Systems in Engineering
- Keywords
- electro-hydraulic systems, active disturbance rejection control, reduced-order control, pressure control, energy efficiency, robustness
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Multiple quadrants displacement tracking control of independent metering electro-hydraulic system. https://app.cochat.ai/papers/10.1038/s41598-024-71147-2
- The paper
- Meng, W., Lutang, L., Aihong, W., Hong, R., & Youshan, G. (2024). Multiple quadrants displacement tracking control of independent metering electro-hydraulic system. Scientific Reports. https://doi.org/10.1038/s41598-024-71147-2
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.