The DOI matches its Crossref record; 6 of the 6 references it cites were found in a registry or an index.
Numerical Modeling of Stainless Steel Structural Components—A Consistent Approach
Abstract
This paper describes numerical modeling of the structural response of stainless steel hollow sections. The aim of the investigation was to develop a consistent approach to the modeling of stainless steel structures. The developed finite element models are more sophisticated than any other reported attempts to model stainless steel structural behavior, with general expressions defined for material stress–strain behavior, enhanced strength corner properties, initial geometric imperfection modes, and amplitudes (local and global), and residual stresses. The general expressions define a consistent means of describing the key input parameters. A compound (two-stage) Ramberg–Osgood model is developed to describe stainless steel material stress–strain behavior in tension and compression. For the prediction of enhanced strength corner properties, a simple, though accurate model is proposed. Characterization of local plate imperfection amplitudes is described whereby a model originally devised for hot-rolled carbon steel cross sections was recalibrated and applied to stainless steel cross sections. Numerical prediction of the key performance measures from tests is achieved with a high degree of accuracy: On average, ultimate load was predicted to within 3% and with a low standard deviation; deformation at ultimate load was within 6%, but exhibited a higher standard deviation; and the general form of the load–deformation response and the failure modes were similar.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Timoshenko, S. P. (1936) · UCLA Biblioteca de Ingenieria Civil · Cited by 7,592
Full-range stress–strain curves for stainless steel alloys
Rasmussen, K. J. R. (2003) · Journal of Constructional Steel Research · doi:10.1016/s0143-974x(02)00018-4 · Cited by 989
Mirambell, E., & Real, E. (2000) · Journal of Constructional Steel Research · doi:10.1016/s0143-974x(99)00051-6 · Cited by 550
Experiments on stainless steel hollow sections—Part 1: Material and cross-sectional behaviour
Gardner, L., & Nethercot, D. A. (2004) · Journal of Constructional Steel Research · doi:10.1016/j.jcsr.2003.11.006 · Cited by 472
Self-citationDesign of Cold‐Formed Stainless Steel Tubular Members. II: Beams
Rasmussen, K. J. R., & Hancock, G. J. (1993) · Journal of Structural Engineering · doi:10.1061/(asce)0733-9445(1993)119:8(2368 · Cited by 236
Design of Cold‐Formed Stainless Steel Tubular Members. I: Columns
Rasmussen, K. J. R., & Hancock, G. J. (1993) · Journal of Structural Engineering · doi:10.1061/(asce)0733-9445(1993)119:8(2349 · Cited by 232
Cited by
The use of stainless steel in structures
Gardner, L. (2005) · Progress in Structural Engineering and Materials · doi:10.1002/pse.190 · Cited by 496
Self-citationExperiments on stainless steel hollow sections—Part 1: Material and cross-sectional behaviour
Gardner, L., & Nethercot, D. A. (2004) · Journal of Constructional Steel Research · doi:10.1016/j.jcsr.2003.11.006 · Cited by 472
Self-citationStructural design of stainless steel concrete filled columns
Lam, D., & Gardner, L. (2008) · Journal of Constructional Steel Research · doi:10.1016/j.jcsr.2008.04.012 · Cited by 327
Self-citationNonlinear analysis of concrete-filled square stainless steel stub columns under axial compression
Tao, Z., Uy, B., Liao, F.-Y., & Han, L.-H. (2011) · Journal of Constructional Steel Research · doi:10.1016/j.jcsr.2011.04.012 · Cited by 282
Han, L.-H., Xu, C.-Y., & Tao, Z. (2019) · Journal of Constructional Steel Research · doi:10.1016/j.jcsr.2018.02.038 · Cited by 193
Metadata
- Authors
- Gardner, L., & Nethercot, D. A.
- Venue
- Journal of Structural Engineering
- Published
- 2004-10
- Volume
- 130
- Issue
- 10
- Pages
- 1586-1601
- ISSN
- 0733-9445 (ISSN-L)
- 1943-541X
- DOI
- 10.1061/(asce)0733-9445(2004)130:10(1586
- OpenAlex
- W2081798539
- Cited by
- 410
- References
- 6
- FWCI
- 33.81
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Numerical Modeling of Stainless Steel Structural Components—A Consistent Approach. https://app.cochat.ai/papers/10.1061/(asce)0733-9445(2004)130:10(1586
- The paper
- Gardner, L., & Nethercot, D. A. (2004). Numerical Modeling of Stainless Steel Structural Components—A Consistent Approach. Journal of Structural Engineering. https://doi.org/10.1061/(asce)0733-9445(2004)130%3A10(1586
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.