The DOI matches its Crossref record; 1 of the 1 references it cites were found in a registry or an index.
Comparison of Electron Elastic-Scattering Cross Sections Calculated from Two Commonly Used Atomic Potentials
Abstract
We have analyzed differential cross sections (DCSs) for the elastic scattering of electrons by neutral atoms that have been derived from two commonly used atomic potentials: the Thomas–Fermi–Dirac (TFD) potential and the Dirac–Hartree–Fock (DHF) potential. DCSs from the latter potential are believed to be more accurate. We compared DCSs for six atoms (H, Al, Ni, Ag, Au, and Cm) at four energies (100, 500, 1000, and 10 000 eV) from two databases issued by the National Institute of Standards and Technology in which DCSs had been obtained from the TFD and DHF potentials. While the DCSs from the two potentials had similar shapes and magnitudes, there can be pronounced deviations (up to 70%) for small scattering angles for Al, Ag, Au, and Cm. In addition, there were differences of up to 400% at scattering angles for which there were deep minima in the DCSs; at other angles, the differences were typically less than 20%. The DCS differences decreased with increasing electron energy. DCSs calculated from the two potentials were compared with measured DCSs for six atoms (He, Ne, Ar, Kr, Xe, and Hg) at energies between 50 eV and 3 keV. For Ar, the atom for which experimental data are available over the largest energy range there is good agreement between the measured DCSs and those calculated from the TFD and DHF potentials at 2 and 3 keV, but the experimental DCSs agree better with the DCSs from the DHF potential at lower energies. A similar trend is found for the other atoms. At energies less than about 1 keV, there are increasing differences between the measured DCSs and the DCSs calculated from the DHF potential. These differences were attributed to the neglect of absorption and polarizability effects in the calculations. We compare transport cross sections for H, Al, Ni, Ag, Au, and Cm obtained from the DCSs for each potential. For energies between 200 eV and 1 keV, the largest differences are about 20% (for H, Au, and Cm); at higher energies, the differences are smaller. We also examine the extent to which three quantities derived from DCSs vary depending on whether the DCSs were obtained from the TFD or DHF potential. First, we compare calculated and measured elastic-backscattered intensities for thin films of Au on a Ni substrate with different measurement conditions, but it is not clear whether DCSs from the TFD or DHF potential should be preferred. Second, we compare electron inelastic mean free paths (IMFPs) derived from relative and absolute measurements by elastic-peak electron spectroscopy and from analyses with DCSs obtained from the TFD and DHF potentials. In four examples, for a variety of materials and measurement conditions, we find differences between the IMFPs from the TFD and DHF potentials ranging from 1.3% to 17.1%. Third, we compare mean escape depths for two photoelectron lines and two Auger-electron lines in solid Au obtained using DCSs from the TFD and DHF potentials. The relative differences between these mean escape depths vary from 4.3% at 70 eV to0.5% at 2016 eV at normal electron emission, and become smaller with increasing emission angle. Although measured DCSs for atoms can differ from DCSs calculated from the DHF potential by up to a factor of 2, we find that the atomic DCSs are empirically useful for simulations of electron transport in solids for electron energies above about 300 eV. The atomic DCSs can also be useful for energies down to at least 200 eV if relative measurements are made.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Handbook of Mathematical Functions
McQuarrie, D. A. (1966) · American Journal of Physics · doi:10.1119/1.1972842 · Cited by 40,433
Cited by
Tanuma, Powell, C. J., & Penn, D. R. (2011) · Surface and Interface Analysis · doi:10.1002/sia.3522 · Cited by 914
Self-citationOptical Constants and Inelastic Electron-Scattering Data for 17 Elemental Metals
Werner, W. S. M., Glantschnig, K., & Ambrosch-Draxl, C. (2009) · Journal of Physical and Chemical Reference Data · doi:10.1063/1.3243762 · Cited by 713
Jablonski, A. (2014) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/47/5/055301 · Cited by 19
Self-citation
Metadata
- Authors
- Jablonski, A., Salvat, F., & Powell, C. J.
- Venue
- Journal of Physical and Chemical Reference Data
- Publisher
- AIP Publishing
- Published
- 2004-03-26
- Volume
- 33
- Issue
- 2
- Pages
- 409-451
- ISSN
- 0047-2689 (ISSN-L)
- 1529-7845
- OpenAlex
- W2091753518
- Cited by
- 228
- References
- 1
- FWCI
- 11.06
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.