CoChat

Pulsed laser ablation of bulk target and particle products in liquid for nanomaterial fabrication

Open access
Huang, Hongkun, Lai, Jiancheng, Lu, Jian, Li, Zhenhua · 2019 · AIP Advances

The DOI matches its Crossref record; 17 of the 17 references it cites were found in a registry or an index; 1 of the 5 sources its claims cite were checked for support.

Abstract

Pulsed laser ablation in liquid (PLAL) is gradually becoming an attractive approach for nanomaterial fabrication because it is a chemically simple and clean method with high product purity. We studied the laser interaction with bulk target and particle products in detail, including mechanism process, target morphology and nanoparticle products. We captured three oscillations of one bubble after laser ablates the bulk target and calculated the variation of pressure and temperature inside the bubble. The results show that the first bubble oscillation has greatest impact on the nanomaterial synthesis, and the most powerful stages for the material synthesis during all the bubble oscillations are the beginning of each expansions and the end of each shrinks. Nanomaterial releases from the bubble at the end of each oscillations. In addition, based on the analysis of ablation cavity on the target, it is found that the cavity depth increases with the number of laser pulses, and then the depth tends to be under saturation status, which means it is difficult to obtain great improvement of the nanomaterial productivity just by prolonging the laser irradiation time. More importantly, the strong interaction between laser and particle products is presented clearly by time-resolved shadowgraphy, which can contributed to the modification of nanoparticle products.

Overview

CoChat Summary

TL;DR

This paper studies pulsed laser ablation in liquid (PLAL) of a Zn target in water, tracking plasma/shockwave, three cavitation-bubble oscillations, target cavity formation, and ZnO nanoparticle products. It finds the first bubble oscillation dominates nanoparticle synthesis, cavity depth saturates with prolonged irradiation, and laser–particle interaction modifies the nanoparticle products.

Key findings

  • Three bubble oscillations were captured after ablating the Zn target: the first had a maximum radius around 4 mm and oscillation times of about 400 µs, 200 µs, and 170 µs for the first, second, and third oscillations; nanomaterial released at the end of each oscillation around 420 µs, 650 µs, and 850 µs.
  • Pressure and relative temperature inside the bubble, calculated from the Rayleigh–Plesset equation, showed that the most powerful stages for material synthesis are the beginning of each expansion and the end of each shrink.
  • Ablation cavity depths were about 13 µm, 60 µm, and 500 µm after 10, 1000, and 5000 laser pulses, respectively; depth increased with pulse number and then tended toward saturation, so prolonging irradiation alone is unlikely to greatly improve nanomaterial productivity.
  • XRD and TEM showed pure, highly crystallized hexagonal wurtzite ZnO nanoparticles with sizes from 10 nm to 42 nm and a peak size around 18 nm; the paper reports that laser interaction with particle products can modify nanoparticle products and make size more uniform with increasing irradiation time.

Methods

  • A Q-switched Nd:YAG laser (1064 nm, 7 ns pulse duration) ablated a 99.995% pure Zn target under water at ambient temperature and pressure, with laser fluence of 12.7 J/cm²; single-pulse mode was used for imaging, and 10 Hz repetitive mode for 30 min to collect nanoparticles.
  • Bubble dynamics were recorded with a high-speed camera (FASTCAM Mini AX100, minimum frame interval 5 µs) and time-resolved shadowgraphy using a 532 nm, 1.2 ns pulse laser, a CCD camera, and a DG535 delay generator with delay below 1 µs.
  • Target morphology was measured by white light confocal microscope; nanoparticle products were characterized by XRD and TEM; pressure and relative temperature inside the bubble were calculated using Rayleigh–Plesset-based equations.

Limitations

  • The paper states no limitations.
  • Evident from the text: the high-speed camera cannot capture plasma and shockwave processes shorter than 5 µs, so those early stages required time-resolved shadowgraphy rather than direct high-speed imaging.
  • Evident from the text: the experiments use only a Zn target in water at one fluence (12.7 J/cm²), one wavelength (1064 nm), and one pulse duration (7 ns), so generality to other materials and laser conditions is not tested; pressure and temperature inside the bubble are calculated rather than directly measured.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1063/1.5082695

Cites

17 of 17 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Image 1
CC-BY · From the PDF
FIG. 1 Schematic diagrams of experimental setup and PLAL process.
FIG. 1 Schematic diagrams of experimental setup and PLAL process.CC-BY · From the PDF
FIG. 2 PLAL process recorded by (a) time-resolved shadowgraphy and (b) high speed camera.
FIG. 2 PLAL process recorded by (a) time-resolved shadowgraphy and (b) high speed camera.CC-BY · From the PDF
Image 4
CC-BY · From the PDF
FIG. 4 Variation of pressure and relative temperature inside bubble.
FIG. 4 Variation of pressure and relative temperature inside bubble.CC-BY · From the PDF
FIG. 5 Target morphology with different laser pulse. (a)(b)(c) Optical micrographs, (d)(e)(f) 3D surface morphology measured by white light confocal microscope, (g)(h)(i) profile of ablation cavity. (a)(d)(g) are measured after 10 laser pulses. (b)(e)(h) are measured after 1000 laser pulses. (c)(f)(i) are measured after 5000 laser pulses.
FIG. 5 Target morphology with different laser pulse. (a)(b)(c) Optical micrographs, (d)(e)(f) 3D surface morphology measured by white light confocal microscope, (g)(h)(i) profile of ablation cavity. (a)(d)(g) are measured after 10 laser pulses. (b)(e)(h) are measured after 1000 laser pulses. (c)(f)(i) are measured after 5000 laser pulses.CC-BY · From the PDF
FIG. 6 Depth of the ablation cavity at different number of laser pulses.
FIG. 6 Depth of the ablation cavity at different number of laser pulses.CC-BY · From the PDF
Image 8
CC-BY · From the PDF
Image 9
CC-BY · From the PDF

Verification

Claims the paper makes

1 Valid · 0 Not valid · 2 Not checked · 38 Own results and interpretations

17 more claims

Create a free account to see all 41 claims and every source verdict.

See all claims — free account
  • It may state two separate claims as one. 18
  • Probably not a substantial claim. 2

Create a free account to see these claims.

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Citations

Cites

Research works printed but not linked: 5

  1. 2018, Laser Physics, 28
  2. 2018, Materials (Basel, Switzerland), 11
  3. 2017, European Physical Journal D, 71
  4. 2017, Journal of Colloid and Interface Science, 487, 106
  5. 2017, Journal of Colloid and Interface Science, 489, 38

Cited by

See all 67

Metadata

Authors
Huang, H., Lai, J., Lu, J., & Li, Z.
Affiliations
  • Nanjing University of Science and Technology (CN)
  • School of Science, Nanjing University of Science & Technology , Nanjing, Jiangsu 210094, People’s Republic of China
Venue
AIP Advances
Published
2019-01-01
Volume
9
Issue
1
ISSN
2158-3226 (ISSN-L)
OpenAlex
W2909307032
Cited by
67
References
17
Citations by year
2026: 3 · 2025: 9 · 2024: 9 · 2023: 13 · 2022: 11 · 2021: 15 · 2020: 6 · 2019: 1
FWCI
2.90
Type
journal article
Language
en
Open access
Licence
Locations
  • AIP Advances (publishedVersion, cc-by)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
Topics
  • Physical Sciences › Materials Science › Materials Chemistry › Laser-Ablation Synthesis of Nanoparticles
  • Physical Sciences › Physics and Astronomy › Acoustics and Ultrasonics › Ultrasound and Cavitation Phenomena
  • Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Laser Material Processing Techniques
Keywords
pulsed laser ablation in liquid, nanomaterial fabrication, bubble oscillation, laser-target interaction, nanoparticle synthesis, laser-particle interaction, time-resolved shadowgraphy, nanoparticle modification

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.