Elastohydrodynamic Lubrication of Line Contacts
The DOI matches its Crossref record; 7 of the 7 references it cites were found in a registry or an index.
Abstract
A procedure for the numerical solution of the complete isothermal elastohydrodynamic lubrication problem for line contacts is outlined. This procedure calls for the simultaneous solution of the elasticity and Reynolds equations. In the elasticity analysis, the conjunction is divided into equal rectangular areas. It is assumed that a uniform pressure is applied over each area. In the numerical analysis of the Reynolds equation, the parameter π = QH3/2 is introduced in order to help the relaxation process. The analysis couples the elasticity and Reynolds equations, going from the inlet to the outlet without making any assumptions other than neglecting side leakage. By using the procedures outlined in the analysis, the influence of the dimensionless speed U, load W, and materials G parameters on minimum film thickness is investigated. Ten cases are used to generate the minimum-film-thickness relationship, ℏmin = 3.07 U0.71G0.57W−0.11. As was first discovered by Dowson and Higginson, the most dominant exponent occurs in association with the speed parameter; the exponent on the load parameter is very small and negative. The materials parameter also carries a significant exponent, although the range of the parameter in engineering situations is limited. The five dimensionless speed parameter values used in obtaining the preceding equation are varied over a range six times the lowest speed value. The four dimensionless load values are varied over a range 1.8 times the lowest load value. Conditions corresponding to the use of solid materials of bronze and steel and lubricants of paraffinic and naphthenic mineral oils are considered in obtaining the exponent in the dimensionless materials parameter. Plots are presented that indicate in detail the pressure distribution, film shape, and flow within the contact. The characteristic pressure spike is clearly in evidence as is the parallel film shape through the central portion of the contact. Minimum film thickness occurs near the outlet of the contact.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“These types of analytical solutions for EHL are based on experimental or numerical solutions for central and minimum film thickness, some of which are based on only ten data points [31].”
From Application of Tribological Artificial Neural Networks in Machine Elements (2023) · cites this paper as [31]
Citations
Cites
Timoshenko, S. P., & Goodier, J. N. (1934) · Virtual Defense Library (Ministerio de Defensa) · Cited by 13,717
Isothermal Elastohydrodynamic Lubrication of Point Contacts: Part III—Fully Flooded Results
Hamrock, B. J., & Dowson, D. (1977) · Journal of Lubrication Technology · doi:10.1115/1.3453074 · Cited by 1,183
Self-citationIsothermals, isopiestics and isometrics relative to viscosity
Barus, C. (1893) · American Journal of Science · doi:10.2475/ajs.s3-45.266.87 · Cited by 662
Ball Bearing Lubrication (The Elastohydrodynamics of Elliptical Contacts)
Hamrock, B. J., Dowson, D., & Tallian, T. E. (1982) · Journal of Lubrication Technology · doi:10.1115/1.3253193 · Cited by 585
Self-citationElasto-hydrodynamic lubrication : the fundamentals of roller and gear lubrication
Dowson, D., & Higginson, G. R. (1966) · Pergamon Press eBooks · Cited by 573
Isothermal Elastohydrodynamic Lubrication of Point Contacts: Part 1—Theoretical Formulation
Hamrock, B. J., & Dowson, D. (1976) · Journal of Lubrication Technology · doi:10.1115/1.3452801 · Cited by 464
Self-citationMAY, A. N. (1961) · Nature · doi:10.1038/192158a0 · Cited by 40
Research works printed but not linked: 7
- Meldahl A., 1941, Brown Boveri Rev., 28, 374
- Grubin A., 1949, Investigation of the Contact Machine Components
- Jacobson B., 1970, Acta Polytech. Scand., Mech. Eng. Ser. No. 54
- Dowson D., 1968, Proc. Inst. Mech. Eng., London, 182, 151
- Dowson D., 1966, Elastohydrodynamic Lubrication—The Fundamentals of Roller and Gear Lubrication
- Okamura H., 1982, Proc. 9th Leeds-Lyon Sympo. on Tribology, 313
- Moes H., 1965, Proc. Inst. Mech. Engrs. 180 (PT. 3B), 244
Cited by
A Three-Dimensional Deterministic Model for Rough Surface Line-Contact EHL Problems
Ren, N., Zhu, D. S., Chen, W., Liu, Y., & Wang, Q. J. (2008) · Journal of Tribology · doi:10.1115/1.2991291 · Cited by 148
Investigation of skidding in angular contact ball bearings under high speed
Wang, Y., Wang, W., Zhang, S., & Zhao, Z. (2015) · Tribology International · doi:10.1016/j.triboint.2015.07.021 · Cited by 141
Experimental analysis of factors influencing the cage slip in cylindrical roller bearing
Selvaraj, A., & Marappan, R. (2010) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-010-2854-5 · Cited by 84
A CFD investigation of lubricant flow in deep groove ball bearings
Peterson, W., Russell, T. E., Sadeghi, F., Berhan, M. T., Stacke, L.-E., & Ståhl, J. (2020) · Tribology International · doi:10.1016/j.triboint.2020.106735 · Cited by 75
Mixed elastohydrodynamic lubrication analysis of line contact with Non-Gaussian surface roughness
Pei, J., Han, X., Tao, Y., & Feng, S. (2020) · Tribology International · doi:10.1016/j.triboint.2020.106449 · Cited by 69
Metadata
- Authors
- Hamrock, B. J., & Jacobson, B. O.
- Affiliations
- Glenn Research Center (US)
- Luleå University of Technology (SE)
- Venue
- A S L E Transactions
- Publisher
- Informa UK Limited
- Published
- 1984-01
- Volume
- 27
- Issue
- 4
- Pages
- 275-287
- ISSN
- 0569-8197 (ISSN-L)
- OpenAlex
- W1973047025
- Cited by
- 85
- References
- 7
- Citations by year
- 2026: 4 · 2025: 5 · 2024: 3 · 2023: 2 · 2022: 4 · 2021: 5 · 2020: 7 · 2019: 5 · 2018: 4 · 2017: 2 · 2016: 1 · 2015: 6 · 2014: 4
- FWCI
- 2.76
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- A S L E Transactions (publishedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Tribology and Lubrication Engineering
- Physical Sciences › Engineering › Mechanical Engineering › Gear and Bearing Dynamics Analysis
- Physical Sciences › Engineering › Mechanics of Materials › Adhesion, Friction, and Surface Interactions
- Keywords
- elastohydrodynamic lubrication, line contact, minimum film thickness, Reynolds equation, elasticity analysis, numerical solution, pressure distribution, film shape, lubricant flow, pressure peaks, side leakage
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Elastohydrodynamic Lubrication of Line Contacts. https://app.cochat.ai/papers/10.1080/05698198408981572
- The paper
- Hamrock, B. J., & Jacobson, B. O. (1984). Elastohydrodynamic Lubrication of Line Contacts. A S L E Transactions. https://doi.org/10.1080/05698198408981572
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.