The DOI matches its Crossref record; 11 of the 11 references it cites were found in a registry or an index.
The measurement of metal droplet temperature in GMA welding by infrared two-colour pyrometry
Abstract
The temperature of metal droplets is essential for clarifying the phenomenon of metal droplet transfer and the melting behaviour of wire; also, it governs the emission of fumes. On the other hand, in situ measurement of the temperature of a metal droplet formed at the tip of a wire during welding was difficult. Hence, this temperature was obtained in many experiences of measurements by such a way that several numbers of metal droplets were collected in a calorimeter to measure the amount of heat content of metal droplet and the heat was converted to temperature. With this way, however, the reliability of the measurement is not necessarily high because the heat loss of the metal droplet during the time when detaching from the wire tip and entering into the calorimeter has to be estimated properly. In this research, two-colour pyrometry has been conducted to obtain the temperature of metal droplets, in which metal droplets have been photographed by a high-speed camera during arc welding, two wavelengths (950 and 980 nm) of light in the infrared range have been selected from the thermal radiation light emitted from the metal droplet at the instant of arc extinguishment by using an imaging spectroscope, and the temperature has been obtained from the intensity ratio of the two waves of light. Consequently, in CO2 arc welding, it has been revealed that the constricted arc causes high-heat input density locally at the arc root portion of a metal droplet and thereby the arc root portion exhibits a higher temperature. By contrast, in MAG (80% Ar–20% CO2) arc welding, it has been disclosed that because the arc covers metal droplets, the temperature distribution in a metal droplet is relatively uniform and the average temperature is lower than in CO2 arc welding.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“A similar method has been successfully applied in high-density plasma environments and high-temperature regions, where direct measurement is difficult, such as in measuring the radiation temperature of electrodes in welding and arc discharges [25, 26].”
From Computational modelling of water-fuelled Hall Effect Thrusters (2025) · cites this paper as [25]
Citations
Cites
Surface temperature measurements for tungsten-based cathodes of high-current free-burning arcs
Haidar, J., & Farmer, A. J. D. (1995) · Journal of Physics D Applied Physics · doi:10.1088/0022-3727/28/10/014 · Cited by 95
Particulate fume generation in arc welding processes.
Heile, R. F., & Hill, D. C. (1975) · Welding Journal · Cited by 48
In-Situ Measurement of Metal Drop Temperature in GMA Short-Circuiting Welding
Hirata, Y., Masahiko, O. N. D. A., Nagaki, H., et al. (2004) · 高温学会誌 · doi:10.7791/jhts.30.140 · Cited by 15
Maruo, H., Hirata, Y., & Noda, Y. (1984) · QUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY · doi:10.2207/qjjws.2.573 · Cited by 14
Temperature measurement by UV thermal radiation
Ohji, T., Yoshioka, N., Shiwaku, T., et al. (1995) · Welding International · doi:10.1080/09507119509548778 · Cited by 9
Droplet transfer phenomena in CO2 arc welding by flux-cored wire.
Suga, T., & Kobayashi, M. (1985) · QUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY · doi:10.2207/qjjws.3.269 · Cited by 8
Mechanism of Fume Reduction in Welding Al-Mg Alloys Using AC Pulsed MIG Process
Tong, H., Nakata, K., Tanaka, M., et al. (2004) · QUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY · doi:10.2207/qjjws.22.375 · Cited by 6
Self-citationThe Measurement of Heat Quantity in Melted Metals
Ozawa, M., & Morita, T. (1963) · JOURNAL OF THE JAPAN WELDING SOCIETY · doi:10.2207/qjjws1943.32.130 · Cited by 6
Temperature measurement by UV thermal radiation.
Ohji, T., Yoshioka, N., Shiwaku, T., et al. (1994) · QUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY · doi:10.2207/qjjws.12.368 · Cited by 6
Fume generation in CO2 arc welding by flux-cored wire.
Suga, T., & Kobayashi, M. (1984) · QUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY · doi:10.2207/qjjws.2.638 · Cited by 5
Research works printed but not linked: 2
- Heile RF, 1975, Weld J., 54, 201s
- Suga T, 1984, Quart J Jpn Weld Soc, 2, 220, 10.2207/qjjws.2.220 · doi:10.2207/qjjws.2.220
Cited by
Oshio, Y., Tauchi, S., Kawasaki, A., & Funaki, I. (2021) · Journal of Applied Physics · doi:10.1063/5.0063942 · Cited by 8
Martens, P. D., Barton, D. A. W., Schartner, A. P., Charles, C., & Boswell, R. W. (2025) · Journal of Electric Propulsion · doi:10.1007/s44205-025-00115-3 · Cited by 4
Oshio, Y., Hirai, K., Watanabe, H., Horisawa, H., & Funaki, I. (2024) · doi:10.21203/rs.3.rs-5180086/v1 · Cited by 1
Metadata
- Authors
- Yamazaki, K., Yamamoto, E., Suzuki, K., Koshiishi, F., Waki, K., Tashiro, S., Tanaka, M., & Nakata, K.
- Affiliations
- Kobe Steel (Japan) (JP)
- The University of Osaka (JP)
- Joining and Welding Research Institute, The University of Osaka (JP)
- Venue
- Welding International
- Publisher
- Informa UK Limited
- Published
- 2010-02
- Volume
- 24
- Issue
- 2
- Pages
- 81-87
- ISSN
- 0950-7116 (ISSN-L)
- 1754-2138
- OpenAlex
- W1976304043
- Cited by
- 50
- References
- 11
- Citations by year
- 2026: 3 · 2025: 3 · 2024: 3 · 2023: 2 · 2022: 3 · 2021: 3 · 2020: 1 · 2019: 2 · 2018: 3 · 2017: 8 · 2016: 5 · 2015: 2 · 2013: 2 · 2012: 5
- FWCI
- 6.67
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Welding International (publishedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Welding Techniques and Residual Stresses
- Physical Sciences › Physics and Astronomy › Atomic and Molecular Physics, and Optics › Vacuum and Plasma Arcs
- Physical Sciences › Engineering › Aerospace Engineering › Calibration and Measurement Techniques
- Keywords
- gas metal arc welding, infrared thermography, droplet transfer, wire melting, fume emissions, CO2 arc welding, high-speed imaging, thermal radiation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: The measurement of metal droplet temperature in GMA welding by infrared two-colour pyrometry. https://app.cochat.ai/papers/10.1080/09507110902842950
- The paper
- Yamazaki, K., Yamamoto, E., Suzuki, K., Koshiishi, F., Waki, K., Tashiro, S., Tanaka, M., & Nakata, K. (2010). The measurement of metal droplet temperature in GMA welding by infrared two-colour pyrometry. Welding International. https://doi.org/10.1080/09507110902842950
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.