Investigation of minimum quantity lubrication effects in drilling CFRP/Ti6Al4V stacks
The DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index.
Abstract
Minimum quantity lubrication (MQL) has been extensively applied to the machining processes of various metallic materials; however, its impact on the drilling characteristics of metallic-composite stacks has not been thoroughly investigated. The present paper is thus aimed at identifying the influences of the MQL environments on the drilling process of one type of composite-titanium compound stacks constituted by T700/FRD-YZR-03 carbon/epoxy laminates and the Ti6Al4V sheets. A series of drilling trials were performed using tungsten carbide twist drills to investigate the feasibility of the MQL for the multilayer stack machining. A quantitative analysis was conducted on various drilling outputs including the drilling forces, surface morphologies of cut composite holes, hole defect extents, hole geometrical accuracy and tool wear signatures. A comparative investigation between the MQL and dry cutting conditions on the stack machinability was also carried out in order to quantify the potentials gained by the MQL machining process. The results indicate that the MQL drilling can yield several benefits in improving the surface morphologies of cut composite holes and in alleviating the drill wear severity, but it fails to reduce the drilling thrust forces, decrease the delamination extents and minimize the hole cylindricity errors when compared with the conventional dry cutting conditions.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“On the other hand, unlike the CFRP layers, the average surface roughness values of the Ti layer remain relatively more consistent [8, 10, 12, 18, 24, 39, 40].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [18]
In the citing paper
“These re-sults show parallelism with the results of studies on si-milar materials in the literature [8, 10, 13, 18, 24, 39, 40].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [18]
In the citing paper
“Again, a lower deviation from dimensional accuracy values was obtained for both CFRP, and Ti6Al4V components at low feed rate drilling of CFRP/Ti6Al4V mixed metallic stack [7, 8, 10, 17, 18, 20, 21, 24, 42].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [18]
In the citing paper
“Lower roundness error values were obtained at the lowest cutting speed when drilling through the metallic stack in one go [7, 8, 10, 17, 18, 20, 21, 24, 42].”
From Evaluation and multi-criteria optimization of surface roughness, deviation from dimensional accuracy and roundness error in drilling CFRP/Ti6Al4 stacks (2022) · cites this paper as [18]
Citations
Cites
The path towards delamination-free drilling of composite materials
Hocheng, H., & Tsao, C. C. (2005) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2005.06.039 · Cited by 449 · cited 1×
“This is firmly associated with the increase of the CFRP thrust forces when using the MQL condition such that a higher thrust force often results in a larger extent of the delamination damage as widely recognized in the scientific literature.([34,35]) Since the MQL has wetting effects which often moisten or even soak t…”
BackgroundEffects of special drill bits on drilling-induced delamination of composite materials
Hocheng, H., & Tsao, C. C. (2006) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2005.10.004 · Cited by 423 · cited 1×
“This is firmly associated with the increase of the CFRP thrust forces when using the MQL condition such that a higher thrust force often results in a larger extent of the delamination damage as widely recognized in the scientific literature.([34,35]) Since the MQL has wetting effects which often moisten or even soak t…”
BackgroundA study of the effect of palm oil as MQL lubricant on high speed drilling of titanium alloys
Rahim, E. A., & Sasahara, H. (2011) · Tribology International · doi:10.1016/j.triboint.2010.10.032 · Cited by 366
Machining of Carbon Fiber Reinforced Plastics/Polymers: A Literature Review
Che, D., Saxena, I., Han, P., Guo, P., & Ehmann, K. F. (2014) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4026526 · Cited by 335 · cited 1×
“However, since the CFRP composites possess anisotropic behavior and heterogeneous architecture, machining of which is likely to induce severe subsurface damage and geometrical imperfections.([10,11]) Additionally, since the reinforcing fibers are featured by high abrasiveness and high hardness, the frictional behavior…”
BackgroundBrinksmeier, E., & Janssen, R. (2002) · CIRP Annals · doi:10.1016/s0007-8506(07)61472-3 · Cited by 275 · cited 2×
“Brinksmeier and Janssen([32]) were among the earliest to apply the MQL method for drilling multilayer composite stacks.”
MethodRawat, S., & Attia, H. (2009) · Wear · doi:10.1016/j.wear.2009.01.031 · Cited by 270
Study of drilling-induced defects for CFRP composites using new criteria
Xu, J., Li, C., Mi, S., An, Q., & Chen, M. (2018) · Composite Structures · doi:10.1016/j.compstruct.2018.06.051 · Cited by 245 · cited 2×
“Regarding the definition of the three-dimensional delamination factor and its measurement, readers are directed to the work done by Xu et al.([33]) Figs.”
MethodSelf-citationRecent advances in drilling hybrid FRP/Ti composite: A state-of-the-art review
Xu, J., Mkaddem, A., & El Mansori, M. (2016) · Composite Structures · doi:10.1016/j.compstruct.2015.09.028 · Cited by 242
Self-citationTool wear in drilling of composite/titanium stacks using carbide and polycrystalline diamond tools
Park, K.-H., Beal, A., Kim, D. (.-W., Kwon, P., & Lantrip, J. (2011) · Wear · doi:10.1016/j.wear.2011.05.038 · Cited by 236
Tool wear of coated drills in drilling CFRP
Wang, X., Kwon, P. Y., Sturtevant, C., Kim, D. (.-W., & Lantrip, J. (2013) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2012.09.019 · Cited by 231 · cited 1×
“Additionally, since the reinforcing fibers are featured by high abrasiveness and high hardness, the frictional behavior at the drill edge-composite interface is rather poor prone to induce stress concentration at the drill edges leading to microchipping or edge rounding.([12,13]) Moreover, as the Ti6Al4V has low therm…”
Background
Cited by
Carbon fiber reinforced polymer in drilling: From damage mechanisms to suppression
Gao, T., Li, C., Wang, Y., Liu, X., An, Q., Li, H. N., Zhang, Y., Cao, H., Liu, B., Wang, D., et al. (2022) · Composite Structures · doi:10.1016/j.compstruct.2022.115232 · Cited by 275
Pimenov, D. Y., Mia, M., Gupta, M. K., Machado, A. R., Tomaz, Í. V., Sarikaya, M., Wojciechowski, S., Mikolajczyk, T., & Kapłonek, W. (2021) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2021.01.031 · Cited by 241
A critical review addressing drilling-induced damage of CFRP composites
Xu, J., Yin, Y., Paulo Davim, J., Li, L., Ji, M., Geier, N., & Chen, M. (2022) · Composite Structures · doi:10.1016/j.compstruct.2022.115594 · Cited by 200
Self-citationXu, J., Li, C., Chen, M., Mansori, M. E., & Davim, J. P. (2019) · Composite Structures · doi:10.1016/j.compstruct.2019.111708 · Cited by 128
Self-citationJiao, F., Li, Y., Niu, Y., Zhang, Z., & Bie, W. (2022) · Composite Structures · doi:10.1016/j.compstruct.2022.116489 · Cited by 93
Metadata
- Authors
- Xu, J., Ji, M., Chen, M., & Ren, F.
- Affiliations
- Shanghai Jiao Tong University (CN)
- Shanghai Aerospace Equipments Manufacturer Company Limited, Shanghai, China
- Corresponding author
- Xu, Jinyang
- Venue
- Materials and Manufacturing Processes
- Publisher
- Informa UK Limited
- Published
- 2019-09-06
- Volume
- 34
- Issue
- 12
- Pages
- 1401-1410
- ISSN
- 1042-6914 (ISSN-L)
- 1532-2475
- OpenAlex
- W2971357891
- Cited by
- 73
- References
- 35
- Citations by year
- 2026: 6 · 2025: 14 · 2024: 8 · 2023: 12 · 2022: 13 · 2021: 10 · 2020: 8 · 2019: 2
- FWCI
- 4.64
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Materials and Manufacturing Processes (publishedVersion)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Advanced machining processes and optimization
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Advanced Machining and Optimization Techniques
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Engineering Technology and Methodologies
- Keywords
- minimum quantity lubrication, drilling, carbon fiber reinforced epoxy, Ti-6Al-4V, dry machining, drilling force, surface morphology, delamination, tool wear, machinability
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Investigation of minimum quantity lubrication effects in drilling CFRP/Ti6Al4V stacks. https://app.cochat.ai/papers/10.1080/10426914.2019.1661431
- The paper
- Xu, J., Ji, M., Chen, M., & Ren, F. (2019). Investigation of minimum quantity lubrication effects in drilling CFRP/Ti6Al4V stacks. Materials and Manufacturing Processes. https://doi.org/10.1080/10426914.2019.1661431
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.