Student or educator? Sign up with your school email and get 6 months of Pro free.
Cited by 311

The DOI matches its Crossref record; 11 of the 11 references it cites were found in a registry or an index.

Atomistic simulations of dislocation mobility in Al, Ni and Al/Mg alloys

Open access
Olmsted, David L, HectorJr, Louis G, Curtin, W A, Clifton, R J·2005·Modelling and Simulation in Materials Science and Engineering

Abstract

Dislocation velocities and mobilities are studied using molecular dynamics simulations for edge and screw dislocations in pure aluminium and nickel, and edge dislocations in Al–2.5%Mg and Al–5.0%Mg random substitutional alloys using EAM potentials. In the pure materials, the velocities of all dislocations are close to linear with the ratio of (applied stress)/(temperature) at low velocities consistent with phonon drag models, and quantitative agreement with the experiment is obtained for the mobility in Al. At higher velocities, different behaviour is observed. The edge dislocation velocity remains dependent solely on (applied stress)/(temperature) up to approximately 1.0 MPa K −1 , and approaches a plateau velocity that is lower than the smallest 'forbidden' speed predicted by continuum models. In contrast, above a velocity around half of the smallest continuum wave speed, the screw dislocation damping has a contribution dependent solely on stress with a functional form close to that predicted by a radiation damping model of Eshelby. At the highest applied stresses, there are several regimes of nearly constant (transonic) velocity separated by velocity gaps in the vicinity of forbidden velocities; various modes of dislocation disintegration and destabilization were also encountered in this regime. In the alloy systems, there is a temperature- and concentration-dependent pinning regime where the velocity drops sharply below the pure metal velocity. Above the pinning regime but at moderate stresses, the velocity is again linear in (applied stress)/(temperature) but with a lower mobility than in the pure metal.

Overview

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1088/0965-0393/13/3/007

Cites

11 of 11 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 11 references

Cited by

See all 311

Metadata

Authors
Olmsted, D. L., HectorJr, L. G., Curtin, W. A., & Clifton, R. J.
Venue
Modelling and Simulation in Materials Science and Engineering
Published
2005-03-22
Volume
13
Issue
3
Pages
371-388
ISSN
  • 0965-0393 (ISSN-L)
  • 1361-651X
OpenAlex
W2044126906
Cited by
311
References
11
FWCI
4.23
Type
journal article
Language
en
Open access
bronze

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Atomistic simulations of dislocation mobility in Al, Ni and Al/Mg alloys. https://app.cochat.ai/papers/10.1088/0965-0393/13/3/007
The paper
Olmsted, D. L., HectorJr, L. G., Curtin, W. A., & Clifton, R. J. (2005). Atomistic simulations of dislocation mobility in Al, Ni and Al/Mg alloys. Modelling and Simulation in Materials Science and Engineering. https://doi.org/10.1088/0965-0393/13/3/007

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.