Optimisation and growth kinetic analysis of Microalgae, Arthrospira platensis in 2-L Photobioreactors
Open accessThe DOI matches its Crossref record; 20 of the 21 references it cites were found in a registry or an index; 4 of the 10 sources its claims cite were checked for support.
Abstract
In recent years, photoautotrophic microalgae are widely recognised due to their diverse yet significant natural values, particularly in healthcare, including pharmaceuticals, cosmetics and feedstock industries. One of the most exploited blue-green microalgae, Arthrospira sp. has been addressed as a potent superfood. However, the microalgal mass-production requires suitable inoculum strain and controlled cultivation conditions for enhanced growth performance. Hence, this study aimed to maximise biomass of Arthrospira platensis chosen strain in a 2 litres indoor photobioreactor under three different parameters which were aeration rate, light intensity and pH of the medium. In the present study, a comparative study of growth performance between helical (S1) and straight form (S2) of A. platensis was conducted and the results revealed that morphological differences did not affect growth performances. Meanwhile, the optimisation based on the parameters studied shows that cultivation of A. platensis with aeration of 0.5 L/min and medium of pH 9.0 yielded the highest biomass production which were 1.500 ± 0.049 g/L. Under different light intensity, A. platensis produced the highest biomass and maximum specific growth rate of 1.142 ± 0.037 g/L and 0.716 ± 0.018 1/day, respectively when cultivated under irradiance of 6000 Lux. In conclusion, compared to before optimisation, biomass and maximum specific growth rate after optimisation was 137% and 24% increased, respectively.
Overview
CoChat Summary
TL;DR
This study optimised biomass production of *Arthrospira platensis* in 2-L indoor photobioreactors by testing aeration rate, pH, and light intensity, after comparing coiled (S1) and straight (S2) trichome strains. The highest biomass was obtained with aeration at 0.5 L/min and pH 9.0, and the highest light-intensity treatment (6000 Lux) gave the greatest biomass and maximum specific growth rate.
Key findings
- Coiled (S1) and straight (S2) trichome forms showed no significant difference in growth performance (one-way ANOVA, P > 0.05); S2 was slightly higher in cell productivity (0.050 ± 0.002 vs. 0.048 ± 0.001 g/L/day), maximum specific growth rate (0.393 ± 0.012 vs. 0.381 ± 0.004 1/day), and maximum cell concentration at OD680nm (1.318 ± 0.059 vs. 1.287 ± 0.019).
- Aeration up to 0.5 L/min improved growth, while 1.0 L/min reduced growth relative to other aeration rates; the unaerated control reached maximum biomass of 0.919 ± 0.041 g/L on day 18. The abstract/conclusion report that cultivation with aeration of 0.5 L/min and pH 9.0 yielded the highest biomass of 1.500 ± 0.049 g/L.
- For pH, maximum dry cell weights were 1.212 ± 0.034 g/L at pH 8.5, 1.370 ± 0.044 g/L at pH 9.5, 1.104 ± 0.055 g/L at pH 10.0, and 1.500 ± 0.049 g/L at pH 9.0 (control); pH 9.0 gave significantly higher biomass than other pH values (p < 0.05).
- Under light intensity, maximum biomass values were 0.942 ± 0.026 g/L at 4000 Lux, 1.016 ± 0.055 g/L at 5000 Lux, and 1.142 ± 0.037 g/L at 6000 Lux, versus 0.822 ± 0.025 g/L at 3000 Lux (control). At 6000 Lux, maximum specific growth rate was 0.716 ± 0.018 1/day, and maximum biomass productivity was 0.111 ± 0.004 g/L/day, about 40% higher than the 0.079 ± 0.003 g/L/day at 3000 Lux. Compared with before optimisation, biomass and maximum specific growth rate after optimisation increased by 137% and 24%, respectively.
Methods
- Two morphological forms of *A. platensis* (S1: coiled trichomes; S2: straight trichome) were obtained from UTEX-LB2340 and cultured in Zarrouk’s medium (ZM). Initial growth-profile experiments used 500 mL Erlenmeyer flasks with 250 mL working medium, 10% (v/v) inoculum, 18 days incubation, and triplicates; S2 was selected for subsequent optimisation.
- Optimisation was performed in a 2-L photobioreactor (bubble column) with 1.5 L ZM, 10% (v/v) inoculum, room temperature, 3000 Lux (42 μmol photons m⁻² s⁻¹), 0 h dark/24 h light, and 18 days unless otherwise stated. Parameters tested sequentially were aeration rate (0.1, 0.5, 1.0 L/min; unaerated control), pH (8.5, 9.5, 10.0; pH 9.0 control), and light intensity (4000, 5000, 6000 Lux; 3000 Lux control).
- Growth was monitored daily by optical density at 680 nm; a standard linear regression between OD readings and microalgal dry cell weight was used to analyse growth curves. Maximum specific growth rate (μ_m) and cell productivity (P_x) were calculated from dry cell weight data, with triplicate means and standard deviations reported.
Limitations
- Stated limitations: Not stated in the paper.
- Evident from the text: the study is limited to a 2-L indoor photobioreactor, 18-day batch cultivations, and a single *A. platensis* strain (S2 after selection), so scale-up to outdoor or industrial systems is not demonstrated.
- Evident from the text: optimisation was sequential, using the optimum condition from each experiment for the next parameter, so potential interactions among aeration, pH, and light intensity were not fully tested; light intensity was tested only up to 6000 Lux, and pH treatments did not include values below 8.5 or above 10.0.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
4 Valid · 0 Not valid · 2 Not checked · 19 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“The changes in biomass production of A. platensis under variation of culture pH may be related to the influence of pH levels on the bioavailability of nutrients and activity of cell components [20].”
What the sources say
- Supportedcites [20] Juneja, 2013, Effects of environmental factors and nutrient availability on the biochemical composition of algae for biofuels production: A Review, Energies source
Section 2.3 (pH; page not provided) says pH determines the availability of CO₂ and essential nutrients, can significantly affect algal metabolism, and may limit algal growth through metabolic inhibition. That supports the citing sentence’s tentative explanation for changes in A. platensis biomass, although the review states the mechanism for algae generally rather than reporting an A. platensis experiment. (LLM, conf=0.86)
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Meanwhile, the further increase in aeration rate to 1.0 L/min resulted in comparatively reduced growth rate as compared to other aeration rates.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In the present study, a comparative study of growth performance between helical (S1) and straight form (S2) of A. platensis was conducted and the results revealed that morphological differences did not affect growth performances.”
- Also stated in: § 4. Conclusion · p. 8 · hedged
“The comparative study on the growth performance of coiled-form (S1) and straight-form (S2) Arthrospira platensis indicated that morphological differences between S1 and S2 did not significantly affect their growth performance due to the similarity in growth pattern, growth characteristics and growth kinetics.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § 4. Conclusion · p. 8 · hedged
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“On the other hand, pH 10.0 recorded the lowest maximum biomass value (1.104 ± 0.055 g/L).”
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“In general, the growth curves for different aeration rate of A. platensis cultures showed similar growth trend.”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
9 more claims
Create a free account to see all 25 claims and every source verdict.
- It may state two separate claims as one. 11
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ 3.3. Effect of pH of the media on microalgae growth · p. 7
“(b) Effect of cultivation pH on biomass productivity (g/L/day) and the maximum specific growth rate (1/day).”
§ 3.4. Effect of light intensity on microalgae growth · p. 7
“by increasing the light intensity from 3000 Lux to 6000 Lux based on Figure 5 (b)”
Citations
Cites
Handbook of Microalgal Culture: Applied Phycology and Biotechnology
(2013) · doi:10.1002/9781118567166 · Cited by 979
Juneja, A., Ceballos, R., & Murthy, G. (2013) · Energies · doi:10.3390/en6094607 · Cited by 835
Spirulina – From growth to nutritional product: A review
Soni, R. A., Sudhakar, K., & Rana, R. S. (2017) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2017.09.010 · Cited by 528 · cited 2×
“Lastly, aeration and mixing are important in ultrahigh density culture as they give a homogenous distribution of the microalgae filaments throughout the growth system which allows them to receive adequate exposure of light and nutrients [5].”
BackgroundAndrade, L. M. (2018) · MOJ Food Processing & Technology · doi:10.15406/mojfpt.2018.06.00144 · Cited by 272
Effects of shear stress on microalgae- A Review
Wang, C., & Lan, C. Q. (2018) · Biotechnology Advances · doi:10.1016/j.biotechadv.2018.03.001 · Cited by 269
Production and nutritive value of Spirulina platensis in reduced cost media
Madkour, F. F., Kamil, A. E.-W., & Nasr, H. S. (2012) · Egyptian Journal of Aquatic Research · doi:10.1016/j.ejar.2012.09.003 · Cited by 231
Role of pH on antioxidants production by spirulina (Arthrospira) platensis
Ismaiel, M. M. S., El-Ayouty, Y. M., & Piercey-Normore, M. (2016) · Brazilian Journal of Microbiology · doi:10.1016/j.bjm.2016.01.003 · Cited by 181
Optimizing microalgae cultivation and wastewater treatment in large-scale offshore photobioreactors
Novoveská, L., Zapata, A. K. M., Zabolotney, J. B., Atwood, M. C., & Sundstrom, E. R. (2016) · Algal Research · doi:10.1016/j.algal.2016.05.033 · Cited by 162 · cited 1×
“cultivation where the high values of light intensity promote biomass production whilst low value promotes phytopigment production [8].”
BackgroundComparative study on the growth performance of Spirulina platensis on modifying culture media
Soni, R. A., Sudhakar, K., & Rana, R. S. (2019) · Energy Reports · doi:10.1016/j.egyr.2019.02.009 · Cited by 150
Attached cultivation for improving the biomass productivity of spirulina platensis
Zhang, L., Chen, L., Wang, J., Chen, Y., Gao, X., Zhang, Z., & Liu, T. (2015) · Bioresource Technology · doi:10.1016/j.biortech.2015.01.025 · Cited by 115
Research works printed but not linked: 4
- Puspanadan, 2018, Optimization of freshwater microalgae, arthrospira Sp. (Spirulina) for high starch production, Int. Food Res. J., 25, 1266
- Matsunaga, 2018, Cryopreservation of spirulina (Arthrospira) platensis NIES-46 by snap-freezing considering trichome morphology, Cryobiol. Cryotechnology, 64, 75
- El-Monem, 2018, Effect of pH on phytochemical and antibacterial activities of spirulina platensis, Int. J. Appl. Env. Sci., 13, 339
- Janarthanan, 2020, Effect of pH on arthrospira platensis production, Alochana Chakra. J., 6, 2297
Cited by
Optimization of Microalgal Biomass Production in Vertical Tubular Photobioreactors
Hawrot-Paw, M., & Sąsiadek, M. (2023) · Energies · doi:10.3390/en16052429 · Cited by 36
Konwar, G., Banik, R., & Geed, S. R. (2025) · Chemical Engineering Journal · doi:10.1016/j.cej.2025.163456 · Cited by 19
Hashmi, Z., Idriss, I. M., Zaini, J., Bakar, M. S. A., & Bilad, M. R. (2025) · Algal Research · doi:10.1016/j.algal.2025.104282 · Cited by 17
Do, S., & Du, Z. (2024) · Energies · doi:10.3390/en17205218 · Cited by 17
Hussin, A. A., Ahmad, N. A. H., Asri, N. F. M., Malek, N. A. N. N., Amin, M. F. M., & Kamaroddin, M. F. (2023) · Bioresource Technology · doi:10.1016/j.biortech.2023.128743 · Cited by 5
Self-citation
Metadata
- Authors
- Hussin, A. A., To, S. W., Sani, M. H., Amin, M. F. M., & Kamaroddin, M. F.
- Affiliations
- University of Technology Malaysia (MY)
- Universiti Malaysia Kelantan (MY)
- Venue
- IOP Conference Series: Earth and Environmental Science
- Publisher
- IOP Publishing
- Published
- 2021-08-01
- Volume
- 842
- Issue
- 1
- Pages
- 012036
- ISSN
- 1755-1315 (ISSN-L)
- 1755-1307
- OpenAlex
- W3197029084
- Cited by
- 7
- References
- 21
- Citations by year
- 2026: 2 · 2025: 2 · 2024: 1 · 2023: 2
- FWCI
- 1.56
- Type
- conference paper
- Language
- en
- Open access
- diamond
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/3.0/ (vor)
- iopscience.iop.org/info/page/text-and-data-mining (tdm)
- Locations
- IOP Conference Series Earth and Environmental Science (publishedVersion, cc-by)
- Funders
- Universiti Malaysia Kelantan
- Universiti Teknologi Malaysia
- Kementerian Kewangan
- Topics
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Algal biology and biofuel production
- Physical Sciences › Earth and Planetary Sciences › Oceanography › Marine and coastal plant biology
- Physical Sciences › Environmental Science › Environmental Chemistry › Aquatic Ecosystems and Phytoplankton Dynamics
- Keywords
- Spirulina platensis, microalgae cultivation, photobioreactors, biomass production, growth kinetics, specific growth rate, air flow rate, light intensity, medium pH
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Optimisation and growth kinetic analysis of Microalgae, Arthrospira platensis in 2-L Photobioreactors. https://app.cochat.ai/papers/10.1088/1755-1315/842/1/012036
- The paper
- Hussin, A. A., To, S. W., Sani, M. H., Amin, M. F. M., & Kamaroddin, M. F. (2021). Optimisation and growth kinetic analysis of Microalgae, Arthrospira platensis in 2-L Photobioreactors. IOP Conference Series: Earth and Environmental Science. https://doi.org/10.1088/1755-1315/842/1/012036
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.