The DOI matches its Crossref record.
Mechanical Properties of Specimens 3D Printed with Virgin and Recycled Polylactic Acid
Open accessAbstract
Abstract With the 26% annual growth rate of additive manufacturing, especially in the area of 3D polymer printing, the amount of waste is increasing at a rapid rate. Limited research in the area of recycling has been produced, yet there are several recycling machines being developed for home use. Despite this work there is no published mechanical data on components produced with filament recycled from 3D printed parts. There is very limited data on mechanical properties of any 3D printed materials. This article compares the properties of parts 3D printed with virgin polylactic acid (PLA) to those printed with recycled PLA. Using commercially available PLA and an entry level 3D printer, tensile and shear specimens were produced and then tested for tensile yield strength, modulus of elasticity, shear yield strength, and hardness. The specimens were then ground up and re-extruded into filament, and a second set of specimens were produced and tested using this recycled PLA filament. Mechanical testing showed that 3D printing with recycled PLA is a viable option. With the recycled filament, tensile strength decreased 10.9%, shear strength increased 6.8%, and hardness decreased 2.4%. The tensile modulus of elasticity was statistically unchanged. Although the average mechanical properties before and after recycling were similar, there was more variability in the results of the recycled filament. Additionally, when printing with the recycled filament there was some nozzle clogging, while none occurred with the virgin filament. Overall, the mechanical properties of specimens 3D printed from recycled PLA filament were similar to virgin properties, encouraging further development in the area of recycling 3D printed filament.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cited by
Cruz Sanchez, F. A., Boudaoud, H., Camargo, M., & Pearce, J. M. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.121602 · Cited by 410
3D printing filament as a second life of waste plastics—a review
Mikula, K., Skrzypczak, D., Izydorczyk, G., Warchoł, J., Moustakas, K., Chojnacka, K., & Witek-Krowiak, A. (2021) · Environmental Science and Pollution Research · doi:10.1007/s11356-020-10657-8 · Cited by 382
Colorado, H. A., Velásquez, E. I. G., & Monteiro, S. N. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.04.062 · Cited by 320
3D printing of polylactic acid: recent advances and opportunities
Joseph, T. M., Kallingal, A., Suresh, A. M., Mahapatra, D. K., Hasanin, M. S., Haponiuk, J., & Thomas, S. (2023) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-022-10795-y · Cited by 313
Kassab, A., Al Nabhani, D., Mohanty, P., Pannier, C., & Ayoub, G. Y. (2023) · Polymers · doi:10.3390/polym15193881 · Cited by 141
Metadata
- Authors
- Anderson, I.
- Venue
- 3D Printing and Additive Manufacturing
- Publisher
- SAGE Publications
- Published
- 2017-06
- Volume
- 4
- Issue
- 2
- Pages
- 110-115
- ISSN
- 2329-7662 (ISSN-L)
- 2329-7670
- OpenAlex
- W2703372140
- Cited by
- 248
- References
- 0
- FWCI
- 8.80
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Mechanical Properties of Specimens 3D Printed with Virgin and Recycled Polylactic Acid. https://app.cochat.ai/papers/10.1089/3dp.2016.0054
- The paper
- Anderson, I. (2017). Mechanical Properties of Specimens 3D Printed with Virgin and Recycled Polylactic Acid. 3D Printing and Additive Manufacturing. https://doi.org/10.1089/3dp.2016.0054
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.